Cadillac STS-V - 2009 Fuse Box Diagram

Cadillac STS-V - 2009 Fuse Box Diagram

Testing the Alarm
1. From inside the vehicle, roll down the window, then
get out of the vehicle, keeping the door open.
2. From outside of the vehicle, with the door open,
lock the vehicle using the power door lock switch
or the keyless access transmitter and close the
door. Wait about 30 seconds until the security light
goes off.
3. Reach in and open the door using the inside door
handle. The horn will sound and the exterior lamps
will flash.
You can turn off the alarm by pressing the unlock button
on the keyless access transmitter or by starting the car.
If the alarm does not sound when it should, check to
see if the horn works. The horn fuse may be blown.
To replace the fuse, see
Fuses and Circuit Breakers on
page 5-123
. If the fuse does not need to be replaced,
you may need to have your vehicle serviced.
To reduce the possibility of theft, always arm the
Theft-Deterrent system when leaving your vehicle.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
Valet Lockout Switch
The valet lockout switch
is located inside the
glove box.
9
(Off):
Press to turn the lockout feature off and allow
the trunk to be opened with either the keyless access
transmitter or the trunk release button located on
the driver’s door.
R
(On):
Press to turn the lockout feature on. The trunk
cannot be unlocked or opened. When the valet lockout
feature is on, the remote start feature and the Universal
Home Remote transmitter will be disabled
Lock the glove box with the key to further secure the
vehicle.
See
Keyless Access System Operation on page 2-5
and
Trunk on page 2-15
for additional information.
2-23
If the engine does not start and the security light comes
on, there may be a problem with the immobilizer
system. Press the START button again.
If the vehicle does not start and the keyless access
transmitter appears to be undamaged, try another
keyless access transmitter. Or, place the transmitter in
the transmitter pocket. See “NO FOBS DETECTED”
under
DIC Warnings and Messages on page 3-79
for
additional information. Check the fuse. See
Fuses and
Circuit Breakers on page 5-123
. If the engine still does
not start with the other transmitter, the vehicle needs
service. If the engine does start, the first transmitter may
be faulty. See your dealer/retailer or have a new keyless
access transmitter programmed to the vehicle.
The immobilizer system can learn new or replacement
keyless access transmitters. Up to four keyless access
transmitters can be programmed for the vehicle.
To program additional transmitters, see “Matching
transmitter(s) to Your Vehicle” under
Keyless Access
System Operation on page 2-5
.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:
The vehicle does not need an elaborate
break-in. But it will perform better in the long run if
you follow these guidelines:
Do not drive at any one constant speed, fast or
slow, for the first 500 miles (805 km). Do not
make full-throttle starts. Avoid downshifting
to brake or slow the vehicle.
Avoid making hard stops for the first 200 miles
(322 km) or so. During this time the new brake
linings are not yet broken in. Hard stops with
new linings can mean premature wear and earlier
replacement. Follow this breaking-in guideline
every time you get new brake linings.
Do not tow a trailer during break-in. See
Towing a
Trailer (Vehicles Without Heavy Duty Cooling) on
page 4-31
or
Towing a Trailer (Vehicles With
Heavy Duty Cooling) on page 4-32
for the trailer
towing capabilities of your vehicle and more
information.
Following break-in, engine speed and load can be
gradually increased.
2-25
Turn and Lane-Change Signals
An arrow on the instrument
panel cluster flashes in the
direction of the turn or
lane change.
Move the lever all the way up or down to signal a turn.
Raise or lower the lever until the arrow starts to flash
to signal a lane change. Hold it briefly until the lane
change is complete. The arrow will automatically
flash three times.
The lever returns to its starting position when it is
released.
If after signaling a turn or lane change the arrow flashes
rapidly or does not come on, a signal bulb may be
burned out.
Have the bulbs replaced. If the bulb is not burned out,
check the fuse. See
Fuses and Circuit Breakers on
page 5-123
.
Turn Signal On Chime
If the turn signal is left on for about 1 mile (1.6 km), a
warning chime will sound and the TURN SIGNAL ON
message will appear on the Driver Information Center
(DIC) display. See “Turn Signal On” under
DIC Warnings
and Messages on page 3-79
for more information.
3-8
The Ignition is On and the HUD Image
Cannot Be Seen
Check to see if:
The HUD unit is covered.
The brightness is adjusted properly.
The HUD display is adjusted to the proper height.
Ambient light in the direction the vehicle is facing
is low.
A fuse is blown. See
Fuses and Circuit Breakers on
page 5-123
.
The windshield is part of the HUD system.
See
Windshield Replacement on page 5-52
.
The following messages may appear in the HUD:
SPEED ALERT
When the Speed Advisor feature is turned on,
HUD displays either the posted or advisory speed as
determined by the information on the map disc in
the navigation system. To turn the Speed Advisor on or
off, see
DIC Operation and Displays on page 3-72
.
The Speed Advisor can be set to show a speed alert
when the vehicle speed exceeds the speed alert limit
as set in the DIC menu. Depending on the level of
the HUD on the vehicle, your HUD may work like either
of the following:
The HUD speedometer will turn red when the
vehicle speed exceeds the speed alert limit.
When the vehicle speed is at or below the alert limit
and above the posted speed or advisory speed,
the speedometer turns yellow. If the Speed
Alert setting in the DIC is set to AT LIMIT, the
speedometer will not turn yellow. When the vehicle
speed is at or below the posted speed or advisory
speed, the speedometer remains green.
The HUD speedometer will turn yellow when the
vehicle speed exceeds the speed alert limit.
When the vehicle speed is at or below the alert
limit, the speedometer remains green.
Posted Speed
Advisory Speed
3-45
PEDAL APPLIED ACC OVERRIDE
When the PEDAL APPLIED ACC OVERRIDE message
displays, the accelerator pedal is being pressed and
the Adaptive Cruise Control is overridden and cannot
automatically apply the brakes. Once the accelerator
pedal is released, the Adaptive Cruise Control will return
to normal operation and be able to apply the brakes,
if needed.
An Adaptive Cruise Control active symbol, alert symbol
or vehicle ahead symbol may also appear. See
Adaptive
Cruise Control on page 3-20
for more information.
Care of the HUD
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity
of the HUD display.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry.
Notice:
When cleaning, be careful not to scratch
the HUD or camera lenses. Do not spray glass
cleaner directly on the HUD lens because the cleaner
could leak inside the unit and cause damage.
Accessory Power Outlet(s)
Accessory power outlets can be used to plug in electrical
equipment, such as a cellular telephone.
The vehicle has one outlet in front of the center console,
one in the center console lid and there may be an
additional outlet in the rear of the center console.
The vehicle may have a small cap that must be
removed to access the accessory power outlet.
Be sure to cover the outlet with the protective cap
when it is not in use.
Notice:
Leaving electrical equipment plugged in for
an extended period of time while the vehicle is off
will drain the battery. Power is always supplied
to the outlets. Always unplug electrical equipment
when not in use and do not plug in equipment
that exceeds the maximum 20 ampere rating.
Certain accessory power plugs may not be compatible
to the accessory power outlet and could result in
blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on the accessory power outlets.
Notice:
Adding any electrical equipment to the
vehicle can damage it or keep other components
from working as they should. The repairs would
not be covered by the vehicle warranty. Do not
3-46
use equipment exceeding maximum amperage
rating of 20 amperes. Check with your dealer/retailer
before adding electrical equipment.
Follow the proper installation instructions that are
included with any electrical equipment you install.
Notice:
Improper use of the power outlet can cause
damage not covered by the warranty. Do not hang
any type of accessory or accessory bracket from
the plug because the power outlets are designed
for accessory power plugs only.
Ashtray(s) and Cigarette Lighter
The vehicle may have an ashtray and cigarette lighter.
Notice:
If papers, pins, or other flammable items
are put in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage the vehicle. Never put flammable items
in the ashtray.
Ashtray
For vehicles with an ashtray, it is located under the
climate control panel on the center console. Press on the
door to release the ashtray. The ashtray automatically
slides open for use.
To empty the ashtray with the ashtray in full open
position, locate the release button to the right of the ash
receiver and slide it to the right (in the direction of the
arrow). The ash receiver will unlock and lift slightly and
can then be easily removed from the housing. To replace
the ash receiver, place it into position in the ashtray
housing and push down firmly until it locks into place.
Cigarette Lighter
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating. Do not use
equipment exceeding maximum amperage rating
of 15 amperes.
The cigarette lighter is located next to the ashtray.
The vehicle does not have any cigarette lighters for
the rear seat passengers.
To activate the cigarette lighter, push it into the heating
element and let go. When the lighter is ready it will
pop back out by itself.
3-47
Oil Pressure Light
For vehicles with an oil
pressure light, if there
is a problem with the oil,
the light may stay on
after the engine is started,
or comes on while
driving.
This light indicates that oil is not going through the
engine quickly enough to keep it lubricated. The engine
could be low on oil or could have some other oil problem.
Have it fixed right away.
The oil light could also come on in the following
situations:
The light comes on briefly when the ignition is
turned on to show that it is working properly.
If it does not come on with the ignition on, there
may be a problem with the fuse or bulb. Have
it fixed right away.
Sometimes when the engine is idling at a stop, a
chime sounds and the light may blink on and off.
This is normal.
{
CAUTION:
Do not keep driving if the oil pressure is low.
The engine can become so hot that it catches fire.
Someone could be burned. Check the oil as soon
as possible and have the vehicle serviced.
Notice:
Lack of proper engine oil maintenance
can damage the engine. The repairs would not be
covered by the vehicle warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
Security Light
For information regarding
this light and the vehicle’s
security system, see
Theft-Deterrent System
on page 2-21
.
3-69
After you have removed the sight shields (if equipped) on the 3.6L V6 engine, here is what you will see:
A. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-124
.
B. Remote Negative (-) Terminal. See
Jump Starting on
page 5-42
.
C. Remote Positive (+) Terminal. See
Jump Starting on
page 5-42
.
D. Battery. See
Battery on page 5-42
.
E. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-54
.
F. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-37
.
G. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-18
.
H. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under
Engine Oil on page 5-18
.
I. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-39
.
J. Engine Coolant Surge Tank and Pressure Cap.
See
Coolant Surge Tank Pressure Cap on page 5-34
and
Cooling System on page 5-26
.
K. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-23
.
L. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-38
.
5-13
After you have removed the sight shields (if equipped) on the 4.6L V8 engine, here is what you will see:
A. Remote Negative (-) Terminal. See
Jump Starting on
page 5-42
.
B. Remote Positive (+) Terminal. See
Jump Starting on
page 5-42
.
C. Battery. See
Battery on page 5-42
.
D. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-54
.
E. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-37
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-18
.
G. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under
Engine Oil on page 5-18
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-39
.
I. Engine Coolant Surge Tank and Pressure Cap.
See
Coolant Surge Tank Pressure Cap on page 5-34
and
Cooling System on page 5-26
.
J. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-23
.
K. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-124
.
L. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-38
.
5-15
After you have removed the sight shields (if equipped) on the 4.4L V8 STS-V engine, here is what you will see:
A. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-124
.
B. Remote Positive (+) Terminal. See
Jump Starting on
page 5-42
.
C. Remote Negative (-) Terminal. See
Jump Starting on
page 5-42
.
D. Battery. See
Battery on page 5-42
.
E. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-54
.
F. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-38
.
G. Intercooler System Pressure Cap. See
Engine
Coolant on page 5-27
.
H. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-37
.
I. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-18
.
J. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under
Engine Oil on page 5-18
.
K. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-39
.
L. Engine Coolant Surge Tank and Pressure Cap.
See
Coolant Surge Tank Pressure Cap on page 5-34
and
Cooling System on page 5-26
.
M. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-23
.
If your vehicle is equipped with front compartment
underhood sight shields, before closing the hood be
sure to reinstall the sight shields. To reinstall the shields,
locate the tabs on the left and right sides and insert them
into the openings in the tower to tower brace. Then insert
the fasteners into the top of the shield and push the
fasteners back into place.
5-17
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to the
vehicle unless you check with your dealer/retailer
first. Some electrical equipment can damage
the vehicle and the damage would not be covered
by the vehicle’s warranty. Some add-on electrical
equipment can keep other components from
working as they should.
Add-on equipment can drain the vehicle battery, even if
the vehicle is not operating.
The vehicle has an airbag system. Before attempting to
add anything electrical to the vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-64
.
Headlamp Wiring
The headlamp wiring is protected by fuses in the fuse
block. An electrical overload will cause the lamps to turn
off. If this happens, have the headlamp wiring checked
right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker. If the wiper motor overheats due to
heavy snow, the wipers will stop until the motor cools
and will then restart.
Power Windows and Other Power
Options
Circuit breakers in the fuse block protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed or
goes away.
Fuses and Circuit Breakers
The wiring circuits in the vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links. This greatly reduces the
chance of fires caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
Fuses of the same amperage can be temporarily
borrowed from another fuse location, if a fuse goes out.
Replace the fuse as soon as you can.
5-123
Underhood Fuse Block
5-124
The underhood fuse block is located in the front of
the engine compartment on the passenger side of
the vehicle. See
Engine Compartment Overview on
page 5-12
for more information on location and removal
procedure for the front compartment underhood sights
shields.
To access the fuses, push in the tabs located on each
side of the fuse block cover, then lift the cover off.
Notice:
Spilling liquid on any electrical components
on the vehicle may damage it. Always keep the
covers on any electrical component.
Fuses JCase
Usage
ABS MTR
ABS Module - ABS Module -
Stabilitrak
AFS
Active Front Steering
BLWR
Blower Motor
FAN 1
Cooling Fan-Low Speed
FAN 2
Cooling Fan-High Speed
LPDB 1
Driver Side Rear Fuse Block
LPDB 2
Driver Side Rear Fuse Block
RPDB 1
Passenger Side Rear Fuse Block
RPDB 2
Passenger Side Rear Fuse Block
Fuses JCase
Usage
SPARE
Spare
SPARE
Spare
STRTR
Starter
Fuses Mini
Usage
A/C CLTCH
Air Conditioning Compressor Clutch
ABS
ABS Module-Stabilitrak
ABS IGN
Antilock Brake Controller
AUX OUTLET
Rear Accessory Power Outlet
BRK VAC
PUMP
Brake Vacuum Pump
CCP
Climate Control Panel
CCP/RLY
COILS
Climate Control Panel, Headlamp
Level Control, Active Cruise Control,
Relay Coils, Starter, Front Blower
ECM 1
Engine Control Module (ECM)
ECM/TCM
BATT
ECM, Transmission Control
Module (TCM)
ECM/TCM IGN
ECM, TCM, Instrument Panel
Cluster
5-125
Fuses Mini
Usage
EKM/I/P MDL
Easy Key Module (EKM), Instrument
Panel Module (I/P MDL)
EVEN COILS
Even Ignition Coils, Even Fuel
Injectors
FOG LAMP
Front Fog Lamps
FRT PWR
OUTLET
Front Accessory Power Outlet
FUEL COOL
Fuel Cooling
HORN
Horn
HTD
WASH/AQS
Heated Headlamp Washer,
Air Quality Sensor
HUD
Heads-Up Display, Steering Column
Switch
I/BEAM
IntelliBeam Relay
I/P MDL/ALDL
Instrument Panel Module, Assembly
Line Data Link Connector
LIC DIM
License Plate, Instrument Panel
Dimming
LT HI BEAM
Driver Side High Beam Headlamp
LT LO BEAM
Driver Side Low Beam Headlamp
LT PRK
Driver Side Park Lamp/Driver Side
Taillamp
Fuses Mini
Usage
ODD COILS
Odd Ignition Coils, Odd Fuel
Injectors
POST O2
SNSR
Post Oxygen Sensor
PRE O2 SNSR
Pre Oxygen Sensor, CAM Sensors
RAIN
SNSR/TPM
Rain Sensor, Relay Coil:
Headlamp Wash
RT HI BEAM
Passenger Side High Beam
Headlamp
RT LO BEAM
Passenger Side Low Beam
Headlamp
RT PRK
Passenger Side Park Lamp,
Passenger Side Taillamp
SPARE
Spare
SPARE
Spare
SPARE
Spare
SPARE
Spare
SPARE
Spare
SPARE
Spare
SPARE
Spare
5-126
Fuses Mini
Usage
V/CHK
Instrument Panel Module-Voltage
Check
WPR
Wipe/Wash Module Assembly
WPR SW/VICS
Rain Sensor, Wiper Switch
Relays
Usage
A/C CMPRSR
CLTCH
Air Conditioning Compressor Clutch
ACCY
Accessory, Rain Sensor, Headlamp
Washer Relay Coil, Windshield
Wiper/Washer Module
BRK VAC
PUMP
Brake Vacuum Pump
FAN S/P
Cooling Fan Series/Parallel
FOG LAMP
Fog Lamps
FRT BLWR
Front Blower Motor
FUEL COOL
Fuel Cooling Pump
HI BEAM
High Beam Headlamp
HI FAN SPD
Cooling Fan High Speed
HORN
Horn
Relays
Usage
LO FAN SPD
Cooling Fan Low Speed
LOW BEAM
W/O HID/HID
Low Beam Headlamp, High Intensity
Discharge (HID)
PRK LAMP
Parking Lamps, Instrument Panel
Dimming, Rear License Plate Lamps
PWR/TRN
Engine Controls
RUN CRNK
Heated Washer Nozzle, Air Quality,
Antilock Brake System, Climate
Control Panel, TCM, ECM,
Instrument Panel Cluster
SPARE
Spare
SPARE
Spare
SPARE
Spare
STRTR
Starter
WPR HI
Windshield Wiper High Speed
Circuit
Breakers
Usage
HDLP WASH
Headlamp Washer Motor
(Circuit Breaker)
5-127
Rear Underseat Fuse Block
Removing the Rear Seat Cushion
Notice:
If you touch the exposed wires with the
metal on the seat cushion, you could cause a
short that could damage the battery and or wires.
Avoid contact between the rear seat and the
fuse center whenever you remove or reinstall
the rear seat. Do not remove covers from any
of the covered parts, and do not store anything
under the seats.
To remove the rear seat cushion, do the following:
1. Pull up on the front of the cushion to release the
front hooks.
2. Pull the cushion up and out toward the front of the
vehicle.
To reinstall the rear seat cushion, do the following:
5-128
{
CAUTION:
A safety belt that is not properly routed through
the seat cushion or is twisted will not provide the
protection needed in a crash. If the safety belt has
not been routed through the seat cushion at all, it
will not be there to work for the next passenger.
The person sitting in that position could be badly
injured. After reinstalling the seat cushion, always
check to be sure that the safety belts are properly
routed and are not twisted.
1. Buckle the center passenger position safety belt,
then route the safety belts through the proper slots
in the seat cushion. Do not let the safety belts
get twisted.
2. Slide the rear of the cushion up and under the
seatback so the rear-locating guides hook into
the wire loops on the back frame.
3. With the seat cushion lowered, push rearward and
then press down on the seat cushion until the
spring locks on both ends engage.
4. Check to make sure the safety belts are properly
routed and that no portion of any safety belt is
trapped under the seat. Also make sure the
seat cushion is secured.
Rear Underseat Fuse Block
There is a fuse block located under the rear seat on the
driver side and passenger side of the vehicle. The rear
seat cushion must be removed to access the fuse blocks.
See “Removing the Rear Seat Cushion” listed previously
in this section.
To access the fuses, push in the two tabs, then lift the
cover off.
5-129
The vehicle may not have all the fuses listed below.
Driver’s Side
Fuses
Usage
AMP
Amplifier
INCLR PUMP
Inner Cooler Pump (Option)
THEFT/SHFT
Theft Sensors, Auto Shifter,
Power Sounder
Fuses
Usage
MRTD MDL
Magnetic Ride Control Module
(Option)
REAR DR MDL
Rear Door Modules
5-130
Fuses
Usage
ELC EXH
Electronic Level Control,
Exhaust Solenoid (Option)
DDM
Driver Door Module, Front Door
SubWoofers (Option)
TV/VICS/SCM
Infotainment (Export Only),
Supervisory Control Module (Option)
REAR
HTD/SEATS
Rear Heated Seats
SPARE
Spare
SPARE
Spare
IGN3
Front Passenger Heated Seat,
Auto Shifter, Occupant Protection,
Electronic Tension Reducer for
Seatbelt
REAR SHLF
SPKR
Rear Shelf Speaker (Option)
MSM
Memory Seat Module Lumbar
TRUNK
RELSE SW
Trunk Release, Valet Lockout
Switch
BCK/UP LAMP
Reverse Lamps, Rear Parking Aid,
Inside Rearview Mirrors
AIR BAG/BATT
Airbag
POS LAMPS
Rear Taillamps
ELC CMPRSR
Automatic Level Control (Option)
Relays
Usage
INCLR PUMP
Inner Cooler Pump (Option)
ELC CMPRSR
Electronic Level Control,
Compressor (Option)
LT POS
Left Rear Taillamp, Position
Lamps (Option)
RT POS
Right Rear Taillamp, Position
Lamps (Option)
RUN
Ignition 3
STDBY LAMP
Rear Taillamps, Position
Lamps (Option)
TRUNK RELSE
Trunk Release Motor
BCK/UP LAMP
Reverse Lamps, Rear Parking Aid,
Inside Rearview Mirror
Circuit
Breakers
Usage
PWR SEATS
Power Seats
Diodes
Usage
SPARE
Spare
Joint
Connector
Usage
J/C
Splice Pack (Green)
5-131
Passenger’s Side
Fuses
Usage
AIRBAG/IGN
Sensing and Diagnostic Monitor,
Automatic Occupant Sensor,
Passenger Supplemental Inflatable
Restraint
CNSTR/VENT
Canister Vent Solenoid
DIFF PUMP
Rear Differential Pump
Fuses
Usage
FRT PDM
Front Passenger Door Module,
Right Power Subwoofer
FUEL PUMP
Fuel Pump
HTD STR
Heated Steering Wheel
RF
HTD/SEAT/XM
Front Passenger Heated Seat,
S-Band™ Antenna
5-132
Fuses
Usage
RDO/ONSTAR
Radio, OnStar
®
INT LAMP
Interior Lamps
LT TRN/LDW
Left Turn Signal, Lane Departure
Warning (Option)
REAR DEFOG
Rear Defogger
REAR/FOG
Rear Fog Lamps (Option)
RIM
Rear Integration Module
RIM /RPA
/ISRVM /CLM
Rear Integration Module, Rear
Parking Aid, Inside Rearview Mirror,
Column Lock Module, Power
Sounder, Active Front Steering
(AFS), Supervisory Control Module
RUN/CRNK
UHBEC Run, CRNK Relay Coil,
Rear Fog Lamp Relay Coil
S/ROOF
Sun Roof Module (Option)
SPARE
Spare
STOP LAMPS
Stop Lamps
RT TRN/SZBA
Right Turn Signal, Side Blind Zone
Alert (Option)
Relays
Usage
DIFF PUMP
Rear Differential Pump (Option)
FUEL PUMP
Fuel Pump
INT LAMP
Interior Lamps
REAR DEFOG
Rear Defogger
REAR/FOG
Rear Fog Lamps (Option)
RUN/CRNK
Ignition 1
SPARE
Spare
STOP LAMP
Stop Lamp
Circuit
Breakers
Usage
WINDOW
MTRS
Power Window Motors Circuit
Breaker
Diodes
Usage
TRUNK DIODE
Trunk Release
Joint
Connector
Usage
J/C
Splice Pack (Blue)
5-133