Buick Rendezvous - 2007 Fuse Box Diagram

Buick Rendezvous - 2007 Fuse Box Diagram

The main components of the instrument panel are the following:
A. Exterior/Interior Lamps Control. See
Exterior
Lamps on page 185
and
Interior Lamps
on page 188
.
B. Turn Signal/Multifunction Lever. See
Turn
Signal/Multifunction Lever on page 177
.
C. Hazard Warning Flasher Button. See
Hazard
Warning Flashers on page 176
.
D. Instrument Panel Cluster. See
Instrument
Panel Cluster on page 212
.
E. Shift Lever. See
Automatic Transaxle Operation
on page 132
.
F. Instrument Panel Outlets. See
Outlet
Adjustment on page 210
.
G. Audio System. See
Audio System(s) on
page 250
.
H. Audio Steering Wheel Controls. See
Audio
Steering Wheel Controls on page 296
.
I. Head-Up Display Switch and Driver Information
Center (DIC) Controls (If Equipped). See
Head-Up Display (HUD) on page 193
and
DIC
Controls and Displays on page 236
.
J. Hood Release. See
Hood Release on
page 363
.
K. Ignition Switch. See
Ignition Positions on
page 128
.
L. Climate Controls. See
Climate Control System
on page 200
,
Dual Climate Control System
on page 203
or
Dual Automatic Climate Control
System on page 206
.
M. Instrument Panel Switchbank. See
Instrument
Panel Switchbank on page 192
.
N. Front Armrest Storage. See
Front Armrest
Storage Area on page 160
.
O. Ashtray/Cigarette Lighter/Accessory Power
Outlet/Cell Phone Storage/Cupholders.
See
Ashtray(s) and Cigarette Lighter on
page 200
,
Accessory Power Outlet(s) on
page 199
,
Cell Phone Storage Area on
page 159
,
Floor Console Storage Area on
page 160
and
Cupholder(s) on page 158
.
P. Floor Console Fuse Block. See
Floor Console
Fuse Block on page 463
.
Q. Glove Box. See
Glove Box on page 158
.
175
L
PUSH Windshield Washer. See
Windshield Washer on page 180
.
CRUISE
I
Cruise Control. See
Cruise
Control on page 181
.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will
return automatically.
An arrow on the
instrument panel cluster
and the HUD display
will flash in the direction
of the turn or lane
change.
To signal a lane change, just raise or lower the
lever until the arrow starts to flash. Hold it
there until you complete your lane change. The
lever will return by itself when you release it.
As you signal a turn or a lane change, if the arrow
flashes faster than normal, a signal bulb may
be burned out and other drivers will not see your
turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when
you signal a turn, check for burned-out bulbs and
check the fuse. See
Fuses and Circuit Breakers
on page 463
.
If you have a trailer towing option with added
wiring for the trailer lamps, the signal indicator will
flash at a normal rate even if a turn signal bulb
is burned out. Check the front and rear turn signal
lamps regularly to make sure they are working.
Turn Signal On Chime
If either turn signal is left on for more than 3/4 mile
(1.2 km), a chime will sound to let the driver
know to turn it off.
If you need to leave the signal on for more than
3/4 mile (1.2 km), turn off the signal and then turn it
back on.
178
To clean the HUD, spray household glass cleaner
on a soft, clean cloth. Wipe the HUD lens gently,
then dry it. Do not spray cleaner directly on the lens
because the cleaner could leak into the unit.
If the ignition is on and you cannot see the HUD
image, check to see if one of the following
conditions exist:
The HUD unit is covered
The HUD dimmer knob is adjusted incorrectly
The HUD image is not adjusted to the
proper height
Ambient light in the direction your vehicle is
facing, is low
A fuse is blown. See
Fuses and Circuit
Breakers on page 463
.
Keep in mind that the windshield is part of the
HUD. See
Windshield Replacement on page 404
.
Ultrasonic Rear Parking
Assist (URPA)
The Ultrasonic Rear Parking Assist (URPA)
system is designed to help you park, while the
vehicle is in REVERSE (R). It operates only at very
low speeds, less than 3 mph (5 km/h). URPA
can help make parking easier and to help
you avoid colliding with objects such as parked
vehicles. The URPA system can detect objects up
to 5 feet (1.5 m) behind the vehicle, and tell
you how close these objects are from your rear
bumper.
Your vehicle’s URPA operates when the shift lever
is moved into REVERSE (R) and the vehicle
speed is less than 3 mph (5 km/h). Four ultrasonic
sensors located at the rear bumper are used to
detect the distance to the object. The URPA
display is located inside the vehicle, near the rear
window. It has three color-coded lights used to
provide distance and system information to
the driver.
196
Accessory Power Outlet(s)
With accessory power outlets you can plug in
electrical equipment such as a cellular telephone
or CB radio.
There is one front power outlet/cigarette lighter
located on the floor console in the cell phone
storage compartment.
There are also two rear power outlets. One is
located in the rear of the floor console below the
vents. The other is located in the rear of the vehicle
on the driver’s side behind the access door.
Pull the cover down to use an accessory power
outlet. When not in use, always cover the
accessory power outlets with the protective cap.
Notice:
Leaving electrical equipment on
for extended periods will drain the battery.
Always turn off electrical equipment when not
in use and do not plug in equipment that
exceeds the maximum amperage rating of
20 amperes.
Certain electrical accessories may not be
compatible with the accessory power outlet and
could result in blown vehicle or adapter fuses.
If you experience a problem, see your dealer for
additional information on the accessory power
outlets.
Notice:
Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should.
The repairs would not be covered by your
warranty. Do not use equipment exceeding
maximum amperage rating of 20 amperes.
Check with your dealer before adding electrical
equipment.
When adding electrical equipment, be sure to
follow the proper installation instructions included
with the equipment.
Notice:
Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
199
Ashtray(s) and Cigarette Lighter
The ashtray is located on the floor console closest
to the instrument panel. Lift the lid to expose
the ashtray. To remove the ashtray, lift it up.
The cigarette lighter is located on the floor console
in the cell phone storage compartment closest
to the driver’s seat. Lift the lid to expose the
cigarette lighter.
To use the lighter, push it in all the way and let
go. When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while
it is heating will not allow the lighter to
back away from the heating element when it is
hot. Damage from overheating may occur to
the lighter or heating element, or a fuse could
be blown. Do not hold a cigarette lighter in
while it is heating.
Notice:
If you put papers, pins, or other
flammable items in the ashtray, hot cigarettes
or other smoking materials could ignite
them and possibly damage your vehicle. Never
put flammable items in the ashtray.
Climate Controls
Climate Control System
With this system you can control the heating,
cooling, and ventilation for your vehicle.
Operation
Turn the right knob clockwise or counterclockwise
to direct the airflow inside your vehicle.
200
This can happen if you have recently replaced your
battery or if your battery has run down. The
diagnostic system is designed to evaluate critical
emission control systems during normal driving.
This may take several days of routine driving. If you
have done this and your vehicle still does not pass
the inspection for lack of OBD system readiness,
your dealer can prepare the vehicle for inspection.
Fuel Gage
When the indicator nears empty, you still have a
little fuel left, but you should get more soon.
If your fuel is low, the warning message in the
message center will come on. See
Low Fuel
Warning Message on page 232
.
Your fuel gage tells you about how much fuel you
have left when the ignition is on.
Here are four things that some owners ask about.
All these things are normal and do not indicate
that anything is wrong with the fuel gage.
At the gas station, the gas pump shuts off
before the gage reads full.
It takes a little more (or less) fuel to fill up
than the gage reads. For example, the
gage reads half full, but it took more (or less)
than half of the tank’s capacity to fill it.
The gage pointer may move while cornering,
braking or speeding up.
The gage may not indicate empty when the
ignition is turned off.
Message Center
The message center is located at the top of the
instrument panel cluster in between the tachometer
and speedometer. It gives you important safety
and maintenance facts.
United States
Canada
225
A. Underhood Fuse Block. See
Underhood Fuse
Block on page 466
.
B. Remote Positive (+) Terminal. See
Jump
Starting on page 394
.
C. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 388
.
D. Radiator Pressure Cap. See
Radiator Pressure
Cap on page 378
.
E. Power Steering Fluid Reservoir. See
Power
Steering Fluid on page 387
.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 365
.
G. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 365
.
H. Automatic Transaxle Fluid Dipstick. See
“Checking the Fluid Level” under
Automatic
Transaxle Fluid on page 372
.
I. Brake Master Cylinder Reservoir. See “Brake
Fluid” under
Brakes on page 389
.
J. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 370
.
K. Engine Coolant Recovery Tank. See
Cooling
System on page 381
.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
See
Engine Compartment Overview on page 364
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you
do not do this, the oil dipstick might not
show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
365
Notice:
If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty. Always
turn off your radio and other accessories when
jump starting your vehicle.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the
cigarette lighter or the accessory power
outlet(s). Turn off the radios and all lamps that
are not needed. This will avoid sparks and help
save both batteries. And it could save the radio!
4. Open the hood on the other vehicle and locate
the positive (+) and negative (
) terminal
locations on that vehicle.
You will not need to access your battery for
jump starting. Your vehicle has a remote
positive (+) jump starting terminal for that
purpose. The terminal is located under a
tethered cap at the front of the underhood fuse
block. See
Engine Compartment Overview on
page 364
for more information on location.
Squeeze the tabs and
swing the cap out of the
way to access the
remote positive (+)
terminal.
You should always use the remote positive (+)
terminal instead of the positive (+) terminal
on the battery.
{
CAUTION:
An electric fan can start up even when the
engine is not running and can injure you.
Keep hands, clothing and tools away from
any underhood electric fan.
3.5L V6 Engine
395
4. Remove the protective cap covering the outlet.
5. Attach the other end of the hose to the
outlet.
6. Press the accessory inflator switch. The light
in the switch will come on to show the system
is working.
If the accessory inflator system does not turn on or
the light does not come on, the fuse may be blown
or installed incorrectly. See
Fuses and Circuit
Breakers on page 463
or see your dealer for
service.
Your accessory inflator will automatically shut off
after about 10 minutes. The light in the switch will
blink. After about one minute you can use the
system again. Press the inflator switch and the
indicator light will come on.
Notice:
If you run the accessory inflator
longer than 30 minutes at a time, you could
damage the inflator. The repairs would not be
covered by your warranty. Run the inflator
for short periods of time only.
After running the accessory inflator for 30 minutes,
wait at least 10 minutes before restarting the
accessory inflator.
To turn off the inflator, do the following:
1. Press the switch and detach the hose, first
from the inflated object, then from the outlet.
2. Put the protective cap back on.
3. Place the inflator kit tools in the pouch, and
store in the glove box.
To put the cover back on, line up the tabs at the
back of the cover and put it in place. Push down the
tab to secure the cover.
426
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to your
vehicle unless you check with your dealer first.
Some electrical equipment can damage your
vehicle and the damage would not be covered
by your warranty. Some add-on electrical
equipment can keep other components from
working as they should.
Add-on equipment can drain your vehicle’s
battery, even if your vehicle is not operating.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 102
.
Headlamp Wiring
The headlamp wiring is protected by internal fuses
in the fuse block. An electrical overload will cause
the lamps to go off and remain off. If this happens,
have your headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an
internal circuit breaker and a fuse. If the motor
overheats due to heavy snow, etc., the wiper will
stop until the motor cools. If the overload is caused
by some electrical problem, be sure to get it fixed.
Power Windows and Other Power
Options
Circuit breakers in the floor console fuse block
protect the power windows and other power
accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting
the circuit until the problem is fixed.
462
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses,
circuit breakers, and fusible thermal links.
Look at the silver-colored band inside the fuse. If
the band is broken or melted, replace the fuse. Be
sure you replace a bad fuse with a new one of the
identical size and rating.
If you ever have a problem on the road and do not
have a spare fuse, you can borrow one that has the
same amperage. Just pick a feature of your vehicle
that you can get along without – like the radio or
cigarette lighter - and use its fuse, if it is the right
amperage. Replace it as soon as you can.
There are two fuse blocks in your vehicle: the floor
console fuse block and the underhood fuse and
relay center.
Floor Console Fuse Block
The floor console fuse block is located to the left
of the glove box near the floor. Pull the door
open to access the fuse block.
463
Fuse
Usage
1
Empty
2
Steering Wheel Radio Controls
3
Power Door Locks
4
Empty
5
Empty
6
Empty
7
Empty
8
Empty
Fuse
Usage
9
Empty
10
Turn Signal and Hazard Lamp
Flashers
11
Power Seats
12
Electronic Level Control (ELC)
Compressor
13
Liftgate and Endgate
14
Rear Auxiliary Power Outlet
15
Electronic Level Control (ELC)
Compressor Relay and Height
Sensor
16
Heated Mirrors
17
Power Mirrors
18
Ignition 1 Module
19
Turn Signal Switch
21
Rear Defogger
22
Airbag Module
24
TCC Switch
25
HVAC Blower Motor
464
Fuse
Usage
26
HVAC Mode and Temperature
Motors and Head-Up Display
28
Accessory Power
29
Windshield Wipers and Washer
30
Instrument Panel Cluster,
Body Control Module (BCM),
PASS-Key
®
III
31
Park Lock Ignition Key Solenoid
32
Rear Window Wiper/Washer
34
Power Sunroof
35
Power Windows
36
Map Lamps, Courtesy Lamps and
Instrument Panel Lights
37
Radio
38
UQ3 Radio Amplifier
39
Head-Up Display
40
Hazard Flashers
Fuse
Usage
41
Instrument Panel Cluster, Climate
Control, Security LED and Remote
Keyless Entry Mode
42
PASS-Key
®
III
44
Body Control Module (BCM)
46
Automatic Occupant Sensing
Module
Relay
Usage
20
Rear Defogger Relay
23
Ignition Relay
27
Accessory Relay
33
Retained Accessory Power Relay
43
Accessory Diode
45
Back-Up Lamps
465
Underhood Fuse Block
This fuse block is located in the engine
compartment, on the passenger’s side of the
vehicle. See
Engine Compartment Overview on
page 364
for more information on location.
The back-up lamp relay (A) is located behind and
to the left of the underhood fuse block.
To remove the cover, press the two tabs in and lift
up the cover.
Fuse
Usage
1
Fuel Pump
2
Air Conditioning Compressor Clutch
3
Horn
4
Anti-lock Brake System (ABS)
5
Engine Control Module (ECM)
466
Fuse
Usage
6
Powertrain Relay
7
Powertrain Sensors
8
Transmission Control Module (TCM)
9
Anti-lock Brake System (ABS)
Solenoids Valves
10
Oxygen Sensor/MAF Sensor
11
Fuel Injectors (Even)
13
Fuel Injectors (Odd)
14
Daytime Running Lamps (DRL)
15
Passenger’s Low-Beam Headlamp
16
Transmission
17
Driver’s Low-Beam Headlamp
18
Driver’s High-Beam Headlamp
19
Ignition Switch Battery Power
20
Parking Lamps
Fuse
Usage
21
Engine Control Module (ECM)
23
Passenger’s High-Beam Headlamp
24
Vent Solenoids
25
DVD
26
Front Fog Lamps
27
Ignition Relay
28
Body Control Module (BCM)
29
S-Band
30
Not Used
31
Cruise Control
32
Front Power Outlets/Lights, OnStar
®
33
Automatic Transaxle Shift Lock
Control System
34
Starter Solenoid Battery Fuse
35
Anti-lock Brake System (ABS) Motor
38
Engine Cooling Fan 2
467
Fuse
Usage
39
Engine Cooling Fan 1
40
Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
41
Main Battery Fuse for Heated Seats,
Air Conditioning, Defogger
44
Main Battery Fuse for Power
Outlets, Level Control, Power Seats,
Mirrors, and Body Computer
46
Main Battery Fuse for Climate
Control Blower and Ignition 3 Relay
47
Main Battery Fuse for Ignition
Switch, Radio, Heads-Up Display
(HUD), Remote Keyless Entry
(RKE), Instrument Cluster, Air
Conditioning, and Body Computer
70
§
Diode for Air Conditioning
Compressor Clutch
§
71
Diode for Ignition
Relay
Usage
49
Horn
50
Fuel Pump
51
Air Conditioning Clutch
52
Daytime Running Lamps (DRL)
53
Low-Beam Headlamps
54
Parking Lamps
55
High-Beam Headlamps
56
Fog Lamps
57
Starter Relay
58
Cooling Fan Series/Parallel
59
Powertrain
60
Cooling Fan 2
61
Cooling Fan 1
62
Ignition
468