Buick Rainier - 2007 Fuse Box Diagram

Buick Rainier - 2007 Fuse Box Diagram

If the engine is running and the security light comes
on, you will be able to restart the engine if you turn
the engine off. However, your Passlock
®
system is
not working properly and must be serviced by your
dealer. Your vehicle is not protected by
Passlock
®
at this time. You may also want to check
the fuse. See
Fuses and Circuit Breakers on
page 465
. See your dealer for service.
In an emergency, call the GM Roadside
Assistance Center. See
Roadside Assistance
Program on page 504
.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:
Your vehicle does not need an
elaborate break-in. But it will perform better in
the long run if you follow these guidelines:
Keep your speed at 55 mph (88 km/h)
or less for the first 500 miles (805 km).
Do not drive at any one constant speed, fast
or slow, for the first 500 miles (805 km).
Do not make full-throttle starts. Avoid
downshifting to brake, or slow, the vehicle.
Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings are not yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every time
you get new brake linings.
Do not tow a trailer during break-in. See
Towing a Trailer on page 339
for the trailer
towing capabilities of your vehicle and more
information.
Following break-in, engine speed and load can
be gradually increased.
108
Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
let you signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever
returns automatically.
An arrow on the
instrument panel
cluster flashes in the
direction of the turn or
lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever returns
by itself when released. The bottom of the outside
rearview mirrors might also have lane change
indicators.
As you signal a turn or a lane change, if the
arrows flash more quickly than normal, a signal
bulb could be burned out and other drivers will not
see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when
you signal a turn, check the fuse. See
Fuses and
Circuit Breakers on page 465
and check for
burned-out bulbs.
If you have a trailer towing option with added
wiring for the trailer lamps, a turn signal flasher is
used. With this flasher installed, the signal
indicator flashes even if a turn signal bulb is
burned out. Check the front and rear turn signal
lamps regularly to make sure they are working.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a
mile (1.2 km), a chime sounds at each flash of
the turn signal. To turn off the chime, move
the turn signal lever to the off position.
156
Remove the cover from the outlet to use the
outlet. Be sure to put the cover back on when not
using the accessory power outlet.
Certain electrical accessories may not be
compatible with the accessory power outlet and
could result in blown vehicle or adaptor fuses.
If you experience a problem, see your dealer
for additional information on the accessory
power outlets.
Notice:
Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should. The
repairs would not be covered by your warranty.
Do not use equipment exceeding maximum
amperage rating of 20 amperes. Check with
your dealer before adding electrical equipment.
When adding electrical equipment, be sure to
follow the proper installation instructions included
with the equipment.
Notice:
Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
Ashtray(s) and Cigarette Lighter
Your vehicle may have this feature. The ashtray is
removable and fits into the front cupholder.
Notice:
If you put papers, pins, or other
flammable items in the ashtray, hot cigarettes
or other smoking materials could ignite
them and possibly damage your vehicle.
Never put flammable items in the ashtray.
To remove the ashtray, pull the covered bin out of
the cupholder.
To use the lighter, press it in all the way, and let
go. When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away
from the heating element when it is hot. Damage
from overheating may occur to the lighter or
heating element, or a fuse could be blown.
Do not hold a cigarette lighter in while it is
heating. Do not use equipment exceeding
maximum amperage rating of 20 amperes.
169
A. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 374
.
B. Engine Coolant Recovery Tank. See
Cooling
System on page 384
.
C. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 391
.
D. Power Steering Fluid Reservoir. See
Power
Steering Fluid on page 390
.
E. Automatic Transmission Fluid Dipstick (Out of
View). See “Checking the Fluid Level” under
Automatic Transmission Fluid on page 375
.
F. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 369
.
G. Radiator Pressure Cap. See
Radiator Pressure
Cap on page 382
.
H. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 369
.
I. Remote Negative (
) Terminal (Marked GND).
See
Jump Starting on page 397
.
J. Brake Master Cylinder Reservoir. See “Brake
Fluid” under
Brakes on page 392
.
K. Battery. See
Battery on page 396
.
L. Engine Compartment Fuse Block. See
Engine
Compartment Fuse Block on page 465
.
367
A. Engine Coolant Recovery Tank. See
Cooling
System on page 384
.
B. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 374
.
C. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 391
.
D. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 369
.
E. Automatic Transmission Fluid Dipstick. See
“Checking the Fluid Level” under
Automatic
Transmission Fluid on page 375
.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 369
.
G. Radiator Pressure Cap. See
Radiator Pressure
Cap on page 382
.
H. Remote Negative (
) Terminal (Marked GND).
See
Jump Starting on page 397
.
I. Power Steering Fluid Reservoir. See
Power
Steering Fluid on page 390
.
J. Brake Master Cylinder Reservoir. See “Brake
Fluid” under
Brakes on page 392
.
K. Engine Compartment Fuse Block. See
Engine
Compartment Fuse Block on page 465
.
L. Battery. See
Battery on page 396
.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
See
Engine Compartment Overview on page 366
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you
do not do this, the oil dipstick might not
show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
369
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to your
vehicle unless you check with your dealer
first. Some electrical equipment can damage
your vehicle and the damage would not
be covered by your warranty. Some add-on
electrical equipment can keep other
components from working as they should.
Add-on equipment can drain your vehicle’s battery,
even if your vehicle is not operating.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 84
.
Headlamps
The headlamp wiring is protected by four fuses.
An electrical overload will cause a lamp to go
on and off. If this happens, have your headlamp
wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by a
circuit breaker and a fuse. If the motor overheats
due to heavy snow or ice, the wiper will stop
until the motor cools. If the overload is caused by
some electrical problem, be sure to get it fixed.
Power Windows and Other
Power Options
Circuit breakers protect the power windows and
other power accessories. When the current load is
too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed
or goes away.
464
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses
and circuit breakers. This greatly reduces
the chance of fires caused by electrical problems.
Look at the silver-colored band inside the fuse.
If the band is broken or melted, replace the fuse.
Be sure you replace a bad fuse with a new
one of the identical size and rating.
If you ever have a problem on the road and
don’t have a spare fuse, you can borrow one
that has the same amperage. Just pick some
feature of your vehicle that you can get
along without — like the radio or cigarette
lighter — and use its fuse, if it is the correct
amperage. Replace it as soon as you can.
Engine Compartment Fuse Block
The fuse block is located under the hood in the
engine compartment on the driver’s side of
the vehicle. See
Engine Compartment Overview
on page 366
for more information on location.
Remove the primary cover by pressing the
two locking tabs. Remove the secondary cover
by snapping off while lifting. To reinstall the
fuse panel cover, reverse the sequence.
465
Fuses
Usage
1
Electrically-Controlled Air
Suspension
2
Passenger’s Side High-Beam
Headlamp
Fuses
Usage
3
Passenger’s Side Low-Beam
Headlamp
4
Back-Up Trailer Lamps
L6 Engine
466
Fuses
Usage
5
Driver’s Side High-Beam
Headlamp
6
Driver’s Side Low-Beam
Headlamp
7
Windshield Wiper
8
Automatic Transfer Case
9
Windshield Washer
10
Powertrain Control Module B
11
Fog Lamps
12
Stoplamp
13
Cigarette Lighter
14
Not Used
15
Electric Adjustable Pedal
16
Truck Body Controller, Ignition 1
17
Crank
18
Airbag
19
Trailer Electric Brake
20
Cooling Fan
21
Horn
22
Ignition E
23
Electronic Throttle Control
24
Instrument Panel Cluster, Driver
Information Center
Fuses
Usage
25
Automatic Shift Lock Control
System
26
Transmission Control Module
(TCM) Canister
27
Backup
28
Powertrain Control Module 1
29
Oxygen Sensor
30
Air Conditioning
31
Truck Body Controller 1
32
Trailer
33
Anti-lock Brakes (ABS)
34
Ignition A
35
Blower Motor
36
Ignition B
50
Passenger’s Side Trailer Turn
51
Driver’s Side Trailer Turn
52
Hazard Flashers
53
Headlamp Driver Module
54
Air Injection Reactor (AIR)
Solenoid
56
Air Injection Reactor (AIR) Pump
58
Vehicle Stability Enhancement
System (StabiliTrak
®
)
59
Regulated Voltage Control
467
Fuses
Usage
1
Electrically-Controlled Air
Suspension
2
Passenger’s Side High-Beam
Headlamp
Fuses
Usage
3
Passenger’s Side Low-Beam
Headlamp
4
Back-Up-Trailer Lamps
V8 Engine
469
Fuses
Usage
5
Driver’s Side High-Beam
Headlamp
6
Driver’s Side Low-Beam
Headlamp
7
Windshield Wiper
8
Automatic Transfer Case
9
Windshield Washer
10
Powertrain Control Module B
11
Fog Lamps
12
Stoplamp
13
Cigarette Lighter
14
Ignition Coils
15
Transmission Control Module
Canister Vent
16
Truck Body Controller, Ignition 1
17
Crank
18
Airbag
19
Trailer Electric Brake
20
Cooling Fan
21
Horn
22
Ignition E
23
Electronic Throttle Control
24
Instrument Panel Cluster, Driver
Information Center
Fuses
Usage
25
Automatic Shift Lock Control
System
26
Engine 1
27
Backup
28
Powertrain Control Module 1
29
Powertrain Control Module
30
Air Conditioning
31
Injector Bank A
32
Trailer
33
Anti-lock Brakes (ABS)
34
Ignition A
35
Blower Motor
36
Ignition B
50
Passenger’s Side Trailer Turn
51
Driver’s Side Trailer Turn
52
Hazard Flashers
53
Transmission
54
Oxygen Sensor Bank B
55
Oxygen Sensor Bank A
56
Injector Bank B
57
Headlamp Driver Module
58
Body Controller 1
59
Electric Adjustable Pedal
470
Fuses
Usage
61
Vehicle Stability Enhancement
System (StabiliTrak
®
)
62
Regulated Voltage Control
Relays
Usage
37
Headlamp Washer
38
Rear Window Wiper
39
Fog Lamps
40
Horn
41
Fuel Pump
42
Windshield Washer
43
High-Beam Headlamp
44
Air Conditioning
45
Cooling Fan
46
Headlamp Driver Module
47
Starter
49
Electric Adjustable Pedal
60
Powertrain
Miscellaneous
Usage
48
Instrument Panel Battery
Rear Underseat Fuse Block
471
Fuses
Usage
01
Passenger Door Control Module
02
Driver Door Control Module
03
Liftgate Module 2
04
Truck Body Controller 3
Fuses
Usage
05
Rear Fog Lamps
06
Blank
07
Truck Body Controller 2
08
Power Seats
472
Fuses
Usage
09
Rear Wiper
10
Driver Door Module
11
Amplifier
12
Passenger Door Module
13
Rear Climate Controls
14
Driver Side Rear Parking Lamps
15
Blank
16
Vehicle Center High-Mounted
Stoplamp (CHMSL)
17
Passenger Side Rear Parking
Lamps
18
Locks
19
Liftgate Module/Driver Seat Module
20
Blank
21
Lock
23
Blank
24
Unlock
25
Blank
26
Blank
27
OnStar
®
Overhead Battery,
OnStar
®
System
28
Sunroof
29
Rainsense™ Wipers
30
Parking Lamps
Fuses
Usage
31
Truck Body Controller Accessory
32
Truck Body Controller 5
33
Front Wipers
34
Vehicle Stop
35
Transmission Control Module
36
Heat Ventilation Air Conditioning B
37
Front Parking Lamps
38
Driver Side Turn Signal
39
Heat Ventilation Air Conditioning I
40
Truck Body Controller 4
41
Radio
42
Trailer Park
43
Passenger Side Turn Signal
44
Heat Ventilation Air Conditioning
45
Rear Fog Lamps
46
Auxiliary Power 1
47
Ignition 0
48
Four-Wheel Drive
49
Blank
50
Truck Body Controller Ignition
51
Brakes
52
Truck Body Controller Run
473