Cadillac XLR - 2006 Fuse Box Diagram

Cadillac XLR - 2006 Fuse Box Diagram

Arming the System
Use one of the three following items listed here to
arm the system:
Press the lock button on the keyless access
transmitter.
Open the door. Lock the door with the power door
lock switch. The security light should flash. Remove
the keyless access transmitter from the interior of the
vehicle and close the door. The security light will stop
flashing and stay on. After 30 seconds, the light
should turn off.
The vehicle can be programmed to automatically
lock the doors and arm the system when you exit the
vehicle. See
DIC Vehicle Personalization on
page 3-78
.
Now, if a door or the trunk lid is opened without the
keyless access transmitter, the alarm will go off.
Your horn will sound for two minutes, then it will go off
to save battery power. And, your vehicle will not start
without a keyless transmitter present.
The theft-deterrent system will not arm if you lock the
driver’s door with the power door lock switch after
the doors are closed.
If your passenger stays in the vehicle when you leave
with the keyless access transmitter, have the passenger
lock the vehicle after the doors are closed. This way the
alarm will not arm, and your passenger will not set it off.
Testing the Alarm
Do the following to test the system:
1. Make sure the trunk lid is latched.
2. Lower the window on the driver’s door.
3. Manually arm the system.
4. Close the doors and wait 30 seconds.
5. Reach through the open window and manually pull
the release lever on the floor.
6. Turn off the alarm by pressing the unlock button on
the transmitter.
If the alarm is inoperative, check to see if the horn
works. If not, check the horn fuse. See
Fuses and Circuit
Breakers on page 6-80
. If the horn works, but the alarm
doesn’t go off, see your dealer.
Disarming the System
Always use your keyless access transmitter to unlock a
door either by pressing the unlock button on the
transmitter or by squeezing the door handle sensor
while you have the transmitter with you. Unlocking a
door any other way will set off the alarm. If your alarm
sounds, press the unlock button on the keyless
access transmitter to disarm it.
2-19
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
G
Turn and Lane-Change Signals. See
Turn and
Lane-Change Signals on page 3-7
.
3
Headlamp High/Low-Beam Changer. See
Headlamp High/Low-Beam Changer on page 3-8
.
-
Fog Lamps. See
Fog Lamps on page 3-31
.
Flash-to-Pass Feature. See
Flash-to-Pass on
page 3-8
.
I
Cruise Control. See
Cruise Control on page 3-12
.
P
Exterior Lamps Control. See
Exterior Lamps on
page 3-28
.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the multifunction lever all the
way up or down. When the turn is finished, the lever will
return automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by itself
when you release it.
If you signal a turn or a lane change and the arrows
flash faster than normal, a signal bulb may be burned
out. Other drivers will not see the turn signal.
Replace burned-out bulbs to help avoid possible
accidents. If the arrows do not go on at all when you
signal a turn, check the fuses and check for burned-out
bulbs. See
Fuses and Circuit Breakers on page 6-80
.
3-7
If the ignition is on and you cannot see the HUD image,
check to see if:
Something is covering the HUD unit.
The brightness is adjusted properly.
The HUD image is adjusted to the proper height.
Ambient light in the direction your vehicle is facing
is low.
A fuse is blown. See
Fuses and Circuit Breakers
on page 6-80
.
Keep in mind that your windshield is part of the HUD
system. See
Windshield Replacement on page 6-46
.
The following Adaptive Cruise Control (ACC) messages
may appear in the HUD:
CRUISE SPEED LIMITED:
This message indicates that
your vehicle speed has been reduced below your set
speed due to ACC limitations. Your set speed is too high
and ACC cannot detect other vehicles at far enough
distances for the system to operate properly.
TIGHT CURVE:
This message indicates that ACC has
reduced your vehicle speed due to a tight curve in
the road. Once the road straightens, ACC will return to
your selected set speed or follow distance setting.
See “Adaptive Cruise Control (ACC)” under
Turn
Signal/Multifunction Lever on page 3-7
for more
information.
You may also see an ACC active symbol, alert symbol
or vehicle ahead symbol. See “Adaptive Cruise
Control (ACC)” under
Turn Signal/Multifunction Lever
on page 3-7
for more information.
3-37
Accessory Power Outlet(s)
The accessory power outlet can be used to connect
electrical equipment such as a cellular phone or
CB radio.
The accessory power outlet is located inside the center
console storage compartment, on the forward left side.
To use the outlet, remove the tethered cap. When not
using it, always cover the outlet with the protective cap.
Notice:
When using an accessory power outlet,
maximum electrical load must not exceed 20 amps.
Always turn off any electrical equipment when
not in use. Leaving electrical equipment on for
extended periods will drain your vehicle’s battery.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Do not use equipment
exceeding maximum amperage rating. Check with
your dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
We recommend that you see a qualified technician or
your dealer for the proper installation of your equipment.
Notice:
Improper use of the power outlet can
cause damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-40
Ashtray(s) and Cigarette Lighter
The ashtray and cigarette lighter are located under a
lid in the front console to the right of the shift lever.
Press the left side of the lid and it will open
automatically.
Notice:
If you put papers, pins, or other flammable
items in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage your vehicle. Never put flammable items in
the ashtray.
Loose objects, such as paper clips, can lodge behind
and beneath the ashtray lid and prevent movement
of the lid. You should avoid putting small, loose objects
near the ashtray.
To use the cigarette lighter, push it in all the way and let
go. When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
Climate Controls
Dual Climate Control System
With this system you can control the heating, cooling
and ventilation for your vehicle.
When your vehicle is first started, the system will
recall the last temperature fan and mode settings for
that driver.
3-41
A. Battery. See
Battery on page 6-36
.
B. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-47
.
C. Underhood Fuse Block. See
Underhood Fuse Block
on page 6-83
.
D. Power Steering Fluid. See
Power Steering Fluid on
page 6-31
.
E. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 6-18
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 6-13
.
G. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 6-13
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 6-33
.
I. Engine Coolant Surge Tank and Pressure Cap.
See
Coolant Surge Tank Pressure Cap on
page 6-23
.
J. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 6-32
.
Engine Oil
If the LOW OIL LEVEL or LOW OIL PRESSURE
message on the Driver Information Center appears
(DIC), it means you need to check your engine oil level
right away. For more information, see LOW OIL LEVEL
and LOW OIL PRESSURE under
DIC Warnings and
Messages on page 3-67
.
You should check your engine oil level regularly; this is
an added reminder.
Checking Engine Oil
It is a good idea to check your engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop.
See
Engine Compartment Overview on page 6-12
for
the location of the engine oil dipstick.
1. Turn off the engine and give the oil several minutes
to drain back into the oil pan. If you do not do this,
the oil dipstick might not show the actual level.
2. Pull out the dipstick and clean it with a paper towel
or cloth, then push it back in all the way. Remove it
again, keeping the tip down, and check the level.
6-13
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and
the damage wouldn’t be covered by your warranty.
Some add-on electrical equipment can keep other
components from working as they should.
Your vehicle has an airbag system. Before attempting to
add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-44
.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker. If the wiper motor overheats due to
heavy snow, the wipers will stop until the motor cools
and will then restart.
A fuse powers the wiper motor. If the fuse blows,
there is an electrical problem. Be sure to have it fixed.
Power Windows and Other
Power Options
Circuit breakers protect the power windows and power
seats. When the current load is too heavy, the circuit
breaker opens and closes, protecting the circuit until the
problem is fixed or goes away.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of fires
caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating. If a fuse should blow, see your dealer
for service immediately.
If you ever have a problem on the road and do not have
a spare fuse, you can “borrow” one that has the same
amperage. Pick some feature of your vehicle that
you can get along without – like the radio or cigarette
lighter – and use its fuse, if it is the correct amperage.
Replace it as soon as you can.
6-80
Instrument Panel Fuse Block
The panel fuse block is located on the passenger’s side
of the vehicle, under the instrument panel and under
the toe-board.
Remove the carpet and toe-board covering to access
the fuse block by pulling at the top of each corner of
the panel. Then turn the fuse block door knob
counterclockwise and pull the door to access the fuses.
Fuses
Usage
1
Spare Fuse
2
Spare Fuse
3
Spare Fuse
4
Spare Fuse
5
Fuse Pull
6
Reverse Lamp
7
Starter/Crank
8
Parking Brake Solenoid A
9
Reverse Lamps
10
BTSI Solenoid, Column Lock
11
Not Used
12
Not Used
13
GMLAN Devices
14
Rear Park Aid, Heated/Cooled Seats,
Windshield Wiper Relays
15
Door Locks
16
Engine Control Module
17
Interior Lights
18
Airbags
19
Not Used
6-81
Fuses
Usage
20
OnStar
®
21
Adaptive Cruise Control (ACC),
Driver Door Switch
22
Power Tilt Wheel, Telescopic Steering
Column, Memory Seat, Driver Seat
Switch, Retractable Hardtop Switch
23
Ignition Switch, Intrusion Sensor
24
Stop Lamp
25
Inside Rearview Mirror, Climate
Control System, Column Lock,
Power Sounder
26
Instrument Panel Cluster,
Head-Up Display (HUD)
27
Radio, S-Band, CD Changer
28
Tap-Up/Tap-Down Switch
29
Climate Control System, Power
Sounder
30
Rear Fog Lamps, Diagnostic Link
Connector
31
Power Folding Mirror
32
Trunk Close Button, Parking Brake
Solenoid B
33
Power Seats
Fuses
Usage
34
Door Controls
35
Run, Accessory Power
36
Not Used
37
Not Used
38
Rainsense™
39
Steering Wheel Control Button Lights
40
Power Lumbar
41
Passenger’s Side Heated Seat
42
Driver’s Side Heated Seat
43
Not Used
44
Retractable Hardtop, Trunk Latch
45
Auxiliary Power
46
Cigar Lighter
47
Park Brake Hold
48
Park Brake Release
49
Not Used
50
Not Used
51
Not Used
52
Fuel Door
6-82
Underhood Fuse Block
The underhood fuse block
is located next to the
engine on the passenger’s
side of the vehicle.
For more information on
location, see
Engine
Compartment Overview
on page 6-12
.
To access the fuses, push in the tab located at the end
of the fuse block cover. Then lift the cover open.
Fuses
Usage
1
Anti-lock Brake System, Electronic
Suspension Control
2
Horn
3
Adaptive Cruise Control (ACC),
Transmission Controls
4
Windshield Wipers
5
Stop/Back-Up Lamps
6
Oxygen Sensor
7
Battery 5
6-83
Fuses
Usage
8
Parking Lamps
9
Electronic Throttle Control
10
Fuel Pump
11
Engine Control Module, Transmission
Control Module
12
Odd Injectors
13
Electronic Suspension Control
14
Emission Controls
15
Air Conditioning Compressor
16
Even Injectors
17
Windshield Washer, Intercooler Pump
18
Headlamp Washer
19
Right Low Beam Headlamp
20
Not Used
21
Left Low Beam Headlamp
22
Fog Lamp
23
Right High Beam Headlamp
24
Left High Beam Headlamp
Fuses
Usage
25
Cooling Fan
26
Battery 3
27
Anti-lock Brakes
28
Climate Controls
29
Battery 2
30
Starter
31
Audio Amplifier
32
Not Used
33
Battery 1
48
Spare
49
Spare
50
Spare
51
Spare
52
Spare
53
Not Used
54
Fuse Puller
6-84