Cadillac SRX - 2006 Fuse Box Diagram

Cadillac SRX - 2006 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
Testing the Alarm
1. From inside the vehicle, roll down the window, then
get out of the vehicle, keeping the door open.
2. From outside of the vehicle, with the door open,
lock the vehicle using the power door lock switch
or the remote keyless entry transmitter and
close the door. Wait approximately 30 seconds
until the security light goes off.
3. Reach in and unlock the door using the manual
lock and open the door. The horn will sound and
the exterior lamps will flash.
You can turn off the alarm by unlocking the driver’s door
with your key, using the unlock button on the remote
keyless entry transmitter or by starting the car with
a valid key.
If the alarm does not sound when it should, check to
see if the horn works. The horn fuse may be blown.
To replace the fuse, see
Fuses and Circuit Breakers
on page 5-96
. If the fuse does not need to be replaced,
you may need to have your vehicle serviced.
To reduce the possibility of theft, always arm the
theft-deterrent system when leaving your vehicle.
Immobilizer
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
2-19
Immobilizer Operation
Your vehicle is equipped
with a passive
theft-deterrent system.
The system works when you turn the key to ON. The
key uses a transponder that matches an immobilizer
control unit in your vehicle. The correct key will start
the vehicle. If the key is ever damaged, you may not
be able to start your vehicle.
When trying to start the vehicle, if the engine does not
start and the security light comes on, the key may
have a damaged transponder. Turn the ignition off
and try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse. See
Fuses
and Circuit Breakers on page 5-96
. If the engine still
does not start with the other key, your vehicle needs
service. If your vehicle does start, the first key may
be faulty. See your dealer who can service the
theft-deterrent system to have a new key made.
It is possible for the theft-deterrent system decoder to
learn the transponder value of a new or replacement
key. Up to 10 additional keys may be programmed for
the vehicle. This procedure is for learning additional
keys only.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service the theft-deterrent system
to have new keys made. To program additional keys
you will require two current driver’s keys. You must add
a step to the following procedure. After Step 2, repeat
Steps 1 and 2 with the second current driver’s key.
Then continue with Step 3.
2-20
Engine Coolant Heater
Your vehicle may be equipped with an engine
coolant heater.
In very cold weather, 0°F (
18°C) or colder, the engine
coolant heater can help. You will get easier starting
and better fuel economy during engine warm-up.
Usually, the coolant heater should be plugged in a
minimum of four hours prior to starting your vehicle.
At temperatures above 32°F (0°C), use of the coolant
heater is not required. Your vehicle may also have
an internal thermostat in the plug end of the cord.
This will prevent operation of the engine coolant heater
when the temperature is at or above 0°F (
18°C) as
noted on the cord.
To Use the Engine Coolant Heater
1. Turn off the engine.
2. Open the hood and unwrap the electrical cord.
For the 3.6L V6 engines, the cord is located in
the engine compartment on the passenger’s side
of the vehicle in front of the fuse block. For the
4.6L V8 engine, remove the engine compartment
beauty cover and the cord is located on the driver’s
side of the vehicle above the strut.
You must remove the plastic cap to access the plug.
3. Plug it into a normal, grounded 110-volt AC outlet.
{
CAUTION:
Plugging the cord into an ungrounded outlet
could cause an electrical shock. Also, the
wrong kind of extension cord could overheat
and cause a fire. You could be seriously
injured. Plug the cord into a properly grounded
three-prong 110-volt AC outlet. If the cord
will not reach, use a heavy-duty three-prong
extension cord rated for at least 15 amps.
4. Before starting the engine, be sure to unplug and
store the cord as it was before to keep it away
from moving engine parts. If you do not, it could
be damaged.
How long should you keep the coolant heater plugged
in? The answer depends on the outside temperature, the
kind of oil you have, and some other things. Instead
of trying to list everything here, we ask that you contact
your dealer in the area where you will be parking
your vehicle. The dealer can give you the best advice
for that particular area.
2-25
Turn and Lane-Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is
complete.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
Raise or lower the lever until the arrow starts to flash
to signal a lane change. Hold it there until the lane
change is complete. The lever returns to its original
position when it’s released.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned-out signal bulb.
Other driver’s won’t see the signal.
Replace burned-out bulbs to help avoid possible
accidents. Check the fuse and for burned-out bulbs if
the arrow fails to work when signaling a turn. See
Fuses
and Circuit Breakers on page 5-96
for more information.
Turn Signal On Chime
If the turn signal is left on for about 1 mile (1.6 km),
a warning chime will sound and the Turn Signal
On message will appear on the Driver Information
Center (DIC) display. See “Turn Signal On” under
DIC
Warnings and Messages on page 3-57
for more
information.
Headlamp High/Low-Beam Changer
Push forward on the turn signal/multifunction lever
to change the headlamps from low to high beam.
Pull the lever back and then release it to change from
high to low beam.
If you turn the vehicle off with the high beams on, the
high beams will be on the next time you start your
vehicle.
This light on the
instrument panel cluster
will be on, indicating
high-beam usage.
3-8
Accessory Power Outlet(s)
Your vehicle is equipped with accessory power outlets.
The outlets can be used to plug in electrical equipment
such as a cellular telephone, CB radio, etc.
Your vehicle has one outlet in front of the center
console on the instrument panel, one in the rear of the
center console, one in the rear compartment, and
there may be an additional outlet in the rear of the
center console.
Your vehicle may have a small cap that must be
removed to access the accessory power outlet.
If it does, when not using the outlet be sure to cover
it with the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain accessory power plugs may not be compatible
to the accessory power outlet and could result in
blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information on
the accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Do not use equipment
exceeding maximum amperage rating. Check
with your dealer before adding electrical equipment.
Follow the proper installation instructions that are
included with any electrical equipment you install.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-23
Ashtray(s) and Cigarette Lighter
Your vehicle may have an ashtray and cigarette lighter.
Notice:
If you put papers, pins, or other flammable
items in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage your vehicle. Never put flammable items in
the ashtray.
Ashtray
The ashtray is located under the climate control panel
on the instrument panel. Press on the door to release
the ashtray.
To empty the ashtray, remove it from the instrument
panel by gripping the edges and pulling straight out.
To reinstall, push the tray back into place.
There may also be ashtrays in the rear doors.
Cigarette Lighter
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
The cigarette lighter is located next to the ashtray.
The vehicle does not have any cigarette lighters for the
rear seat passengers.
To activate the cigarette lighter, push it into the heating
element and let go. When the lighter is ready it will
pop back out by itself.
3-24
A. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-97
.
B. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-38
.
C. Battery. See
Battery on page 5-42
.
D. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-32
.
E. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-37
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
G. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under
Engine Oil on page 5-16
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-39
.
I. Engine Coolant Surge Tank and Pressure Cap. See
Coolant Surge Tank Pressure Cap on page 5-29
and
Cooling System on page 5-32
.
J. Engine Air Cleaner/Filter. See
Engine Air Cleaner/
Filter on page 5-24
.
5-13
A. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-97
.
B. Battery. See
Battery on page 5-42
.
C. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-32
.
D. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-38
.
E. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-37
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
G. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under
Engine Oil on page 5-16
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-39
.
I. Engine Coolant Surge Tank and Pressure Cap. See
Coolant Surge Tank Pressure Cap on page 5-29
and
Cooling System on page 5-32
.
J. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-24
.
5-15
Your vehicle has a remote negative (
) ground
location, as shown in the illustration. It is located
between the battery and the underhood fuse block.
You should always use this remote ground
location, instead of the terminal on the battery.
Notice:
If you connect a negative cable to the ECM,
ECM mounting bracket, or any cables that attach
to the ECM bracket, you may damage the ECM.
Always attach the negative cable to your vehicle’s
remote negative ground location, instead of the
ECM, ECM bracket, or any cables attached to the
ECM bracket.
{
CAUTION:
An electric fan can start up even when the
engine is not running and can injure you.
Keep hands, clothing and tools away from
any underhood electric fan.
5-44
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and
the damage wouldn’t be covered by your warranty.
Some add-on electrical equipment can keep other
components from working as they should.
Your vehicle has an airbag system. Before attempting
to add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-61
.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker. If the wiper motor overheats due to
heavy snow, the wipers will stop until the motor cools
and will then restart.
Power Windows and Other Power
Options
Circuit breakers protect the power windows and power
seats. When the current load is too heavy, the circuit
breaker opens and closes, protecting the circuit until
the problem is fixed or goes away.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of fires
caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure
you replace a bad fuse with a new one of the identical
size and rating. If a fuse blows, see your dealer for
service immediately.
If you ever have a problem on the road and don’t
have a spare fuse, you can “borrow” one that has the
same amperage. Pick some feature of your vehicle that
you can get along without – like the radio or cigarette
lighter – and use its fuse, if it is the correct amperage.
Replace it as soon as you can.
The fuses are located in three fuse blocks, one located
in the engine compartment on the passenger’s side
and the other two under the rear seat.
5-96
J Cases
Usage
LOW FAN
Low Cooling Fan Motor
BLOWER
PWM Fan Motor Assembly
STARTER
Starter Solenoid
EBCM
Electronic Brake Control Module
Fuses
Usage
RT PARK
Passenger’s Side Taillamp
Assembly, Front Sidemarker and
Front Parking Lamp Assembly
HORN
Dual Horn Assembly
LT HI BEAM
Driver’s Side High-Beam Headlamp
LT LOW BEAM
Driver’s Side Low-Beam Headlamp
RT LOW BEAM
Passenger’s Side Low-Beam
Headlamp
RT HI BEAM
Passenger’s Side High-Beam
Headlamp
HFV6 ECM
High Feature V6 ECM (Electronic
Control Module)
REAR WPR
Rear Wiper Motor
THEFT
ECM, TCM (Transmission Control
Module), PASS-Key
®
III+ Module
Fuses
Usage
LT PARK
Driver’s Side Taillamp Assembly,
Front Sidemarker and Front Parking
Lamp Assembly
LIC/DIMMING
Rear License Plate Assembly,
DIM (Dash Integration Module)
DIM/ALDL
DIM, ALDL (Assembly Line
Data Link)
FLASHER
Turn Signal/Hazard Flasher Module
V8 ECM
V8 ECM, Canister Purge
STRG CTLS
Steering Wheel Control Pad,
Headlamp Switch
STARTER RLY
Jumper to Starter Relay
WASH NOZ
Driver’s and Passenger’s Side
Heated Washer Nozzles
ODD COILS
Odd Ignition Coils, Fuel Injectors,
Odd Injection Coils
TCM/IPC
TCM, ECM and IPC (Instrument
Panel Cluster)
SPARE
Not Used
ABS
Anti-lock Brake System
VICS
Vehicle Information and
Communication System
5-99
Fuses
Usage
SPARE
Not Used
SPARE
Not Used
IGN SW
Ignition Switch (Power to IGN-3
and CRANK)
VOLT CHECK
DIM
ECM/TCM
ECM, TCM, IPC,
PASS-Key
®
III+ Module
WPR MOD
Windshield Wiper Module Assembly
POSTO2
Post O2 Sensors
COMP CLUTCH Compressor Clutch
WPR SW
Windshield Wiper/Washer Switch
FOG LAMP
Fog Lamps
OUTLET
Center Console Accessory
Power Outlet
Fuses
Usage
EVEN COILS
Even Injection Coils
I/P OUTLET
Instrument Panel Accessory
Power Outlet
CCP
Climate Control
PREO2/CAM
Driver’s and Passenger’s Side
Oxygen Sensors, CAM Phaser
SPARE
Not Used
SPARE
Not Used
SPARE
Not Used
Circuit
Breakers
Usage
HDLP WASH
C/B-OPT
Headlamp Washer Motor (Optional)
5-100
Rear Underseat Fuse Block
(Driver Side)
The driver’s side rear fuse block is located under the
rear seat on the driver’s side of the vehicle. The carpet
must be lifted up to access the rear fuse block.
To access the fuse block, push in the two tabs located
at each end of the fuse block cover. Then lift the
cover off.
Relays
Usage
BASS RELAY
MICRO
Brake Lamps
SPARE
Not Used
ELC RELAY
MINI
Electronic Level Control (ELC)
Compressor Motor
SPARE
Not Used
L POSITION
RELAY MICRO
Driver’s Side Position Lamp
R POSITION
RELAY MICRO
Passenger’s Side Position Lamp
IGN 3 RELAY
MICRO
Heated Seat Modules, Air Inlet
Motor, Shifter Assembly
STANDING
LAMP
RLY MICRO
Control for Position Lamp Relays
SPARE
Not Used
REV LAMP
RELAY MICRO
ISRVM (Inside Rearview Mirror),
License Plate Lamp Assembly
5-101
Fuses
Usage
L FRT HTD
SEAT MOD
Driver’s Heated Seat Module
MEM/ADAPT
SEAT
Driver’s Power Seat Switch,
Memory Seat Module
THEFT
Universal Garage Door Opener,
Intrusion Sensor, Diversity
Antenna Module
REVERSE
LAMP
ISRVM (Inside Rearview Mirror),
License Plate Lamp Assembly
SPARE
Not Used
POSITION
LAMP
Taillamp Assemblies,
Front Position Lamp Assemblies
SPARE
Not Used
ELC COMP
Electronic Level Control (ELC)
Compressor, Electronic Level
Control (ELC) Solenoid
AUDIO
Radio, OnStar
®
Module
FFS SW
Flip Fold Seat Switch
REAR DR MOD Rear Door Modules
FFSM
Flip Fold Seat Module
Fuses
Usage
DRIVER
DR MOD
Driver’s Door Module
BASS
Taillamps, Center High-Mounted
Stop Lamp, Flasher Module,
ABS Module, Trailer Lamps
HDLP
LEVELING
Headlamp Leveling System
Chassis Sensors (Export Only)
SPARE
Not Used
CCP
Climate Control Panel (CCP)
IGN 3
Heated Seat Modules, Air Inlet
Motor, Shifter Assembly
J Cases
Usage
AMP
Audio Amplifier
ELC
Electronic Level Control (ELC)
Compressor
Circuit
Breakers
Usage
SEAT C/B
Power Seat Switches,
Memory Seat Module
5-102
Rear Underseat Fuse Block
(Passenger Side)
The passenger’s side rear fuse block is located under
the rear seat on the passenger’s side of the vehicle.
The carpet must be lifted up to access the rear
fuse block.
To access the fuse block, push in the two tabs located
at each end of the fuse block cover. Then lift the
cover off.
Relays
Usage
PRIMARY
QUARTER A/C
RELAY MINI
Rear Air Conditioning
SPARE
Not Used
REAR DEFOG
RELAY MINI
Rear Window Defogger
SPARE
Not Used
AFTERBOIL
RELAY MICRO
Afterboil Pump
INT LAMP
RELAY MICRO
Hush Panel Lamps, Puddle Lamps,
Overhead Courtesy Lamp Assembly
IGN 1 RELAY
MICRO
Ignition Switch
SPARE
Not Used
RAP RELAY
(MICRO)
Sunroof
FUEL PUMP
MOTOR
RLY MICRO
Fuel Pump Motor
5-103
Fuses
Usage
INTERIOR
LAMP
Hush Panel Lamps, Puddle Lamps,
Overhead Courtesy Lamp Assembly
RT
FRT DR MOD
Passenger’s Door Module
RIM
Rear Integration Module (RIM),
Ignition Switch, Key Lock Cylinder
REAR FOG
LAMP
Rear Fog Lamps (Export Only)
SUSPNTN
Suspension Module
VICS/RAP
TV Tuner Assembly, Vehicle
Information Communication
System (VICS) Module, Sunroof
SPARE
Not Used
POWER
SOUNDER
Power Sounder, Inclination Sensor
AFTERBOIL
Afterboil Heater Pump
CANISTER
VENT
Canister Vent Solenoid
FUEL
PUMP MTR
Fuel Pump Motor
REAR HVAC
Rear Climate Control System
Fuses
Usage
R FRT HTD
SEAT MOD
Passenger’s Side Heated
Seat Module
REAR HATCH
Rear Hatch Latch
AIR BAG
Sensing Diagnostic Module (SDM)
REAR DEFOG
Rear Window Defogger Element
IGN 1
Shifter, Power Sounder, Rear
Parking Aid, Rearview Mirror, RIM
SPARE
Not Used
SPARE
Not Used
J Cases
Usage
SUNROOF MOD Power Sunroof Module
POWER
LIFTGATE
Power Liftgate
Circuit
Breakers
Usage
DR MOD
PWR C/B
Door Modules
5-104