Buick Rendezvous - 2005 Fuse Box Diagram

Buick Rendezvous - 2005 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
PASS-Key
®
III Operation
Your vehicle is equipped
with the PASS-Key
®
III
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key
®
III is a passive
theft deterrent system.
This means you don’t have
to do anything different
to arm or disarm the
system. It works when you
insert or remove the key
from the ignition.
When the PASS-Key
®
III system senses that someone
is using the wrong key, it shuts down the vehicle’s
starter and fuel systems. The starter will not work and
fuel will stop being delivered to the engine. Anyone
using a trial-and-error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
If the SECURITY message is shown on the Message
Center when trying to start the vehicle, the key may
have a damaged transponder. See
PASS-Key
®
III Security Message on page 3-57
. Turn the ignition off
and try to start the vehicle again.
If the engine still does not start, and the key appears to be
undamaged, try another ignition key. At this time, you
may also want to check the fuse. See
Fuses and Circuit
Breakers on page 5-105
. If the engine still does not start
with the other key, your vehicle needs service. If your
vehicle does start, the first key may be faulty. See your
dealer who can service the PASS-Key
®
III to have a new
key made.
It is possible for the PASS-Key
®
III decoder to program
the transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for programming additional keys only. If
all the currently programmed keys are lost or do not
operate, you must see your dealer or a locksmith who can
service PASS-Key
®
III to have keys made and
programmed to the system.
See your dealer who can service PASS-Key
®
III to get a
new key blank that is a cut exactly as the ignition key
that operates the system.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS-Key
®
III to
have new keys made. To program additional keys you
will need two current driver’s keys (black in color).
You must add a step to the following procedure. After
Step 3 repeat Steps 1 through 3 with the second current
driver’s key. Then continue with Step 4.
2-18
The main components of the instrument panel are the following:
A. Exterior/Interior Lamps Control. See
Exterior Lamps
on page 3-14
and
Interior Lamps on page 3-16
.
B. Turn Signal/Multifunction Lever. See
Turn
Signal/Multifunction Lever on page 3-7
.
C. Hazard Warning Flasher Button. See
Hazard
Warning Flashers on page 3-6
.
D. Instrument Panel Cluster. See
Instrument Panel
Cluster on page 3-38
.
E. Shift Lever. See
Automatic Transaxle Operation
on page 2-23
.
F. Instrument Panel Outlets. See
Outlet Adjustment
on page 3-36
.
G. Audio System. See
Audio System(s) on page 3-75
.
H. Audio Steering Wheel Controls. See
Audio
Steering Wheel Controls on page 3-133
.
I. Head-Up Display Switch and Driver Information
Center (DIC) Controls (If Equipped). See
Head-Up
Display (HUD) on page 3-21
and
DIC Controls
and Displays on page 3-64
.
J. Hood Release. See
Hood Release on page 5-11
.
K. Ignition Switch. See
Ignition Positions on page 2-20
.
L. Climate Controls. See
Climate Control System on
page 3-28
,
Dual Climate Control System on
page 3-30
or
Dual Automatic Climate Control System
on page 3-33
.
M. Instrument Panel Switchbank. See
Instrument Panel
Switchbank on page 3-20
.
N. Front Armrest Storage. See
Front Armrest Storage
Area on page 2-40
.
O. Ashtray/Cigarette Lighter/Accessory Power
Outlet/Cell Phone Storage/Cupholders. See
Ashtrays
and Cigarette Lighter on page 3-27
,
Accessory
Power Outlets on page 3-26
,
Cell Phone Storage
Area on page 2-39
,
Floor Console Storage Area on
page 2-39
and
Cupholder(s) on page 2-39
.
P. Floor Console Fuse Block. See
Floor Console Fuse
Block on page 5-105
.
Q. Glove Box. See
Glove Box on page 2-38
.
3-5
To adjust the HUD so you can see it properly, do the
following:
1. Start your engine and turn the dimmer knob to the
desired HUD image brightness.
The brightness of the HUD image is determined by
the ambient light conditions in the direction your
vehicle is facing and where you have the HUD
dimmer knob set. If you are facing a dark object or a
heavily shaded area, your HUD may anticipate that
you are entering a dark area and may begin to dim.
2. Adjust the driver’s seat. If you change your seat
position, you may have to readjust your HUD.
3. Press the UP or DN buttons until the HUD image is
easy to see and then press the DN button until the
HUD image is as low as possible, but remains
in full view straight ahead near the front bumper.
The HUD image can only be adjusted up and down,
not side-to-side.
4. To turn the image off, turn the dimmer knob
counterclockwise until it stops.
If the sun comes out or it becomes cloudy, you may
need to adjust the HUD brightness again using
the dimmer knob. Polarized sunglasses could make the
HUD image harder to see.
When you first start the vehicle the display will show
BUICK and the Buick logo for a few seconds. If it is cold
outside, this display may stay on for up to a minute.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity
of the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry
it. Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you cannot see the HUD image,
check to see if one of the following conditions exist:
The HUD unit is covered
The HUD dimmer knob is adjusted incorrectly
The HUD image is not adjusted to the proper height
Ambient light in the direction your vehicle is
facing, is low
A fuse is blown. See
Fuses and Circuit Breakers on
page 5-105
.
If you ever have to have your windshield replaced, be
sure to get one that is designed for the HUD or your
HUD image may look blurred and out of focus.
3-23
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on the accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the
equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Ashtrays and Cigarette Lighter
The ashtray is located on the floor console closest to
the instrument panel. Lift the lid to expose the ashtray.
To remove the ashtray, lift it up.
The cigarette lighter is located on the floor console in
the cell phone storage compartment closest to the
driver’s seat. Lift the lid to expose the cigarette lighter.
To use the lighter, push it in all the way and let go.
When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating. Do not
use anything other than the cigarette lighter in the
heating element.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
3-27
A. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-107
.
B. Remote Positive (+) Terminal. See
Jump Starting on
page 5-42
.
C. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-36
.
D. Automatic Transaxle Fluid Dipstick. See “Checking
the Fluid Level” under
Automatic Transaxle Fluid
on page 5-22
.
E. Brake Master Cylinder. See “Brake Fluid” under
Brakes on page 5-38
.
F. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-37
.
G. Battery. See
Battery on page 5-41
.
H. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-28
.
I. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
J. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-16
.
K. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-21
.
L. Coolant Recovery Tank. See
Engine Coolant on
page 5-25
.
5-13
A. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-37
.
B. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-107
.
C. Battery. See
Battery on page 5-41
.
D. Remote Positive (+) Terminal. See
Jump Starting on
page 5-42
.
E. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-28
.
F. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-36
.
G. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
H. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-16
.
I. Brake Master Cylinder. See “Brake Fluid” under
Brakes on page 5-38
.
J. Automatic Transaxle Fluid Dipstick. See “Checking
the Fluid Level” under
Automatic Transaxle Fluid
on page 5-22
.
K. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-21
.
L. Coolant Recovery Tank. See
Engine Coolant on
page 5-25
.
5-15
Notice:
If you leave your radio or other accessories
on during the jump starting procedure, they could
be damaged. The repairs would not be covered
by your warranty. Always turn off your radio and
other accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or the accessory power outlet(s). Turn off
the radios and all lamps that are not needed. This
will avoid sparks and help save both batteries.
And it could save the radio!
4. Open the hood on the other vehicle and locate the
positive (+) and negative (
) terminal locations on
that vehicle.
You will not need to access your battery for jump
starting. Your vehicle has a remote positive (+) jump
starting terminal for that purpose. The terminal is
located under a tethered cap at the front of the
underhood fuse and relay center. See
Engine
Compartment Overview on page 5-12
for more
information on location.
Pull up on the cap to
access the remote
positive (+) terminal. You
should always use the
remote positive (+) terminal
instead of the positive (+)
terminal on the battery.
{
CAUTION:
An electric fan can start up even when the
engine is not running and can injure you. Keep
hands, clothing and tools away from any
underhood electric fan.
5-43
{
CAUTION:
Inflating something too much can make it
explode, and you or others could be injured.
Be sure to read the inflator instructions, and
inflate any object only to its recommended
pressure.
To use your accessory inflator system, do the following:
1. Turn the ignition to ACCESSORY or ON.
2. Attach the appropriate nozzle adapter, if required,
to the end of the hose that has the pressure gage.
3. Attach that end of the hose to the object you wish
to inflate.
4. Remove the protective cap covering the outlet.
5. Attach the other end of the hose to the outlet.
6. Press the accessory inflator switch. The light in the
switch will come on to show the system is working.
If the accessory inflator system does not turn on or the
light does not come on, the fuse may be blown or
installed incorrectly. See
Fuses and Circuit Breakers on
page 5-105
or see your dealer for service.
Your accessory inflator will automatically shut off after
about 10 minutes. The light in the switch will blink. After
about one minute you can use the system again. Press
the inflator switch and the indicator light will come on.
Notice:
If you run the accessory inflator longer than
30 minutes at a time, you could damage the
inflator. The repairs would not be covered by your
warranty. Run the inflator for short periods of
time only.
After running the accessory inflator for 30 minutes, wait at
least 10 minutes before restarting the accessory inflator.
To turn off the inflator, do the following:
1. Press the switch and detach the hose, first from the
inflated object, then from the outlet.
2. Put the protective cap back on.
3. Place the inflator kit tools in the pouch, and store in
the glove box.
To put the cover back on, line up the tabs at the back of
the cover and put it in place. Push down the tab to
secure the cover.
5-71
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your
vehicle unless you check with your dealer first.
Some electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add-on electrical equipment can
keep other components from working as they
should.
Your vehicle has an airbag system. Before attempting to
add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-82
.
Headlamp Wiring
The headlamp wiring is protected by internal fuses in
the fuse block. An electrical overload will cause the
lamps to go off and remain off. If this happens, have
your headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker and a fuse. If the motor overheats due to
heavy snow, etc., the wiper will stop until the motor
cools. If the overload is caused by some electrical
problem, be sure to get it fixed.
Power Windows and Other Power
Options
Circuit breakers in the floor console fuse block protect
the power windows and other power accessories.
When the current load is too heavy, the circuit breaker
opens and closes, protecting the circuit until the
problem is fixed.
5-104
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers,
and fusible thermal links.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
If you ever have a problem on the road and do not have
a spare fuse, you can borrow one that has the same
amperage. Just pick a feature of your vehicle that
you can get along without – like the radio or cigarette
lighter - and use its fuse, if it is the right amperage.
Replace it as soon as you can.
There are two fuse blocks in your vehicle: the floor
console fuse block and the underhood fuse and relay
center.
Floor Console Fuse Block
The floor console fuse block is located to the left of the
glove box near the floor. Pull the door open to access
the fuse block.
5-105
Fuse
Usage
1
Empty
2
Steering Wheel Radio Controls
3
Power Door Locks
4
Empty
5
Empty
6
Empty
7
Empty
8
Empty
9
Empty
10
Turn Signal and Hazard Lamp
Flashers
Fuse
Usage
11
Power Seats
12
Electronic Level Control (ELC)
Compressor
13
Liftgate and Endgate
14
Rear Auxiliary Power Outlet
15
Electronic Level Control (ELC)
Compressor Relay and Height
Sensor
16
Heated Mirrors
17
Power Mirrors
18
Ignition 1 Module
19
Turn Signal Switch
21
Rear Defogger
22
Air Bag Module
24
TCC Switch
25
HVAC Blower Motor
26
HVAC Mode and Temperature
Motors and Head-Up Display
28
Not Used
29
Windshield Wipers and Washer
30
Instrument Panel Cluster, Body
Control Module (BCM),
PASS-Key
®
III
31
Park Lock Ignition Key Solenoid
32
Rear Window Wiper/Washer
5-106
Fuse
Usage
34
Power Sunroof
35
Power Windows
36
Map Lamps, Courtesy Lamps and
Instrument Panel Lights
37
Radio
38
UQ3 Radio Amplifier
39
Head-Up Display
40
Hazard Flashers
41
Instrument Panel Cluster, Climate
Control, Security LED and Remote
Keyless Entry Mode
42
PASS-Key
®
III
44
Body Control Module (BCM)
46
Advanced Occupant System Module
Relay
Usage
20
Rear Defogger Relay
23
Ignition Relay
27
Accessory Relay
33
Retained Accessory Power Relay
43
Accessory Diode
45
Back-Up Lamps
Underhood Fuse Block
This fuse block is located in the engine compartment,
on the passenger’s side of the vehicle. See
Engine
Compartment Overview on page 5-12
for more
information on location.
The back-up lamp relay (A) is located behind and to the
left of the underhood fuse block.
To remove the cover, press the two tabs in and lift up
the cover.
5-107
Fuse
Usage
1
Fuel Pump
2
Air Conditioning Compressor Clutch
3
Horn
4
Engine Controls-Emissions and
Sensors
5
Power Control Module
(PCM)-Battery Power
6
Anti-Lock Brakes (ABS) Control
Module
7
Transaxle Solenoids
Fuse
Usage
9
Anti-lock Brake System (ABS)
Solenoid Valves
10
Oxygen Sensors-Emissions Control
11
Fuel Injectors
13
Engine Controls
14
Daytime Running Lamps (DRL)
15
Passenger’s Low-Beam Headlamp
17
Driver’s Low-Beam Headlamp
18
Driver’s High-Beam Headlamp
19
Ignition Switch Battery Power
20
Parking Lamps
23
Passenger’s High-Beam Headlamp
24
Vent Solenoids
25
DVD
26
Front Fog Lamps
27
Ignition Relay, Neutral Start Switch,
Powertrain Control Module (PCM)
28
Body Control Module-Battery Power
29
S Band, Remote Digital Radio
Receiver
30
All-Wheel Drive (AWD) Module
31
Cruise Control
32
Front Power Outlets/Lights, OnStar
®
3400 V6 Engine
5-108
Fuse
Usage
33
Automatic Transaxle Shift Lock
Control System
34
Starter Solenoid Battery Fuse
35
Anti-lock Brake System (ABS) Motor
38
Engine Cooling Fan 2
39
Engine Cooling Fan 1
40
Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
41
Main Battery Fuse for Heated Seats,
Air
44
Main Battery Fuse for Power
Outlets, Level Control, Power Seats
and Mirrors and Body Computer
46
Main Battery Fuse for Climate
Control Blower and Ignition 3 Relay
47
Main Battery Fuse for Ignition
Switch, Radio, Heads-Up Display,
Remote Keyless Entry (RKE),
Instrument Cluster, Air Conditioning
and Body Computer
70
§
Diode for Air Conditioning
Compressor Clutch
Relay
Usage
49
Horn
50
Fuel Pump
51
Air Conditioning Clutch
52
Daytime Running Lamps (DRL)
53
Low-Beam Headlamps
54
Parking Lamps
55
High-Beam Headlamps
56
Fog Lamps
57
Starter Relay
58
Cooling Fan
59
Ignition 1 Relay
60
Cooling Fan 2
61
Cooling Fan 1
5-109
Fuse
Usage
1
Fuel Pump
2
Air Conditioning Compressor Clutch
3
Horn
4
Anti-lock Brake System (ABS)
5
Engine Control Module (ECM)
6
Powertrain Relay
7
Powertrain Sensors
8
Transmission Control Module (TCM)
9
Anti-lock Brake System (ABS)
Solenoids Valves
Fuse
Usage
10
Oxygen Sensor/MAF Sensor
11
Fuel Injectors (Even)
13
Fuel Injectors (Odd)
14
Daytime Running Lamps (DRL)
15
Passenger’s Low-Beam Headlamp
16
Transmission
17
Driver’s Low-Beam Headlamp
18
Driver’s High-Beam Headlamp
19
Ignition Switch Battery Power
20
Parking Lamps
21
Engine Control Module (ECM)
23
Passenger’s High-Beam Headlamp
24
Vent Solenoids
25
DVD
26
Front Fog Lamps
27
Ignition Relay
28
Body Control Module (BCM)
29
S Band
30
All-Wheel Drive (AWD) Module
31
Cruise Control
32
Front Power Outlets/Lights, OnStar
®
33
Automatic Transaxle Shift Lock
Control System
34
Starter Solenoid Battery Fuse
3.6L V6 Engine
5-110
Fuse
Usage
35
Anti-lock Brake System (ABS) Motor
38
Engine Cooling Fan 2
39
Engine Cooling Fan 1
40
Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
41
Main Battery Fuse for Heated Seats,
Air Conditioning, Defogger
44
Main Battery Fuse for Power
Outlets, Level Control, Power Seats,
Mirrors, and Body Computer
46
Main Battery Fuse for Climate
Control Blower and Ignition 3 Relay
47
Main Battery Fuse for Ignition
Switch, Radio, Heads-Up Display
(HUD), Remote Keyless Entry
(RKE), Instrument Cluster, Air
Conditioning, and Body Computer
70
§
Diode for Air Conditioning
Compressor Clutch
§
71
Diode for Ignition
Relay
Usage
49
Horn
50
Fuel Pump
51
Air Conditioning Clutch
52
Daytime Running Lamps (DRL)
53
Low-Beam Headlamps
54
Parking Lamps
55
High-Beam Headlamps
56
Fog Lamps
57
Starter Relay
58
Cooling Fan S/P
59
Powertrain
60
Cooling Fan 2
61
Cooling Fan 1
62
Ignition
5-111