Buick Rainier - 2005 Fuse Box Diagram

Buick Rainier - 2005 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
Remember, the theft-deterrent system won’t activate if
you lock the doors with a key or use the manual
door lock. It activates only if you use a power door lock
switch with the door open, or with the remote keyless
entry transmitter. You should also remember that
you can start your vehicle with the correct ignition key if
the alarm has been set off.
Here’s how to avoid setting off the alarm by accident:
If you don’t want to activate the theft-deterrent
system, the vehicle should be locked with the door
key
after
the doors are closed.
Always unlock a door with a key, or use the remote
keyless entry transmitter. Unlocking a door any
other way will set off the alarm.
If you set off the alarm by accident, unlock any door with
the key. You can also turn off the alarm by pressing
unlock on the remote keyless entry transmitter. The alarm
won’t stop if you try to unlock a door any other way.
Testing the Alarm
The alarm can be tested by following these steps:
1. From inside the vehicle, lower the driver’s window
and open the driver’s door.
2. Activate the system by locking the doors with the
power door lock switch while the door is open, or
with the remote keyless entry transmitter.
3. Get out of the vehicle, close the door and wait for
the security light to go out.
4. Then reach in through the window, unlock the door
with the manual door lock and open the door. This
should set off the alarm.
When the alarm is set the power door unlock switch is
not operational.
If the alarm does not sound when it should but the
headlamps flash, check to see if the horn works. The
horn fuse may be blown. To replace the fuse, see
Fuses
and Circuit Breakers on page 5-93
.
If the alarm does not sound or the headlamps do not
flash, the vehicle should be serviced by your dealer.
2-17
Passlock
®
Your vehicle is equipped with the Passlock
®
theft-deterrent system.
Passlock
®
is a passive theft-deterrent system that
enables fuel if the ignition lock cylinder is turned with a
valid key. If a correct key is not used or the ignition lock
cylinder is tampered with, the fuel system is disabled and
the vehicle will not start.
During normal operation, the security light will turn off
approximately five seconds after the key is turned
to RUN.
If the engine stalls and the security light flashes, wait
about 10 minutes until the light stops flashing before
trying to restart the engine. Remember to release the key
from START as soon as the engine starts.
If the engine does not start after three tries, the vehicle
needs service.
If the engine is running and the security light comes on,
you will be able to restart the engine if you turn the engine
off. However, your Passlock
®
system is not working
properly and must be serviced by your dealer. Your
vehicle is not protected by Passlock
®
at this time. You
may also want to check the fuse. See
Fuses and Circuit
Breakers on page 5-93
. See your dealer for service.
In an emergency, call the GM Roadside Assistance
Center. See
Roadside Assistance Program on page 7-5
.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:
Your vehicle does not need an elaborate
break-in. But it will perform better in the long run if
you follow these guidelines:
Keep your speed at 55 mph (88 km/h) or less for
the first 500 miles (805 km).
Do not drive at any one speed — fast or
slow — for the first 500 miles (805 km). Do not
make full-throttle starts.
Avoid making hard stops for the first
200 miles (322 km) or so. During this time your
new brake linings are not yet broken in. Hard
stops with new linings can mean premature
wear and earlier replacement. Follow this
breaking-in guideline every time you get new
brake linings.
Do not tow a trailer during break-in. See
Towing
a Trailer on page 4-50
for more information.
2-18
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you signal
a turn, check the fuse. See
Fuses and Circuit Breakers
on page 5-93
and check for burned-out bulbs.
If you have a trailer towing option with added wiring for
the trailer lamps, a different turn signal flasher is
used. With this flasher installed, the signal indicator will
flash even if a turn signal bulb is burned out. Check
the front and rear turn signal lamps regularly to make
sure they are working.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the
turn signal. To turn off the chime, move the turn signal
lever to the off position.
Headlamp High/Low-Beam Changer
To change the headlamps from low to high beam,
push the lever toward the instrument panel. To return to
low-beam headlamps, pull the multifunction lever
toward you. Then release it.
When the high beams are
on, this indicator light on
the instrument panel
cluster will also be on.
Flash-to-Pass
This feature lets you use your high-beam headlamps to
signal a driver in front of you that you want to pass.
It works even if your headlamps are in the automatic
position.
To use it, pull the turn signal lever toward you, then
release it.
If your headlamps are in the automatic position or on
low beam, your high-beam headlamps will turn on.
They’ll stay on as long as you hold the lever toward you.
The high-beam indicator on the instrument panel
cluster will come on. Release the lever to return to
normal operation.
3-8
Battery Run-Down Protection
This feature shuts off the dome, courtesy and vanity
if they are left on for more than 20 minutes when
the ignition is off. This will keep your battery from
running down.
If the battery run-down protection shuts off the interior
lamps, it may be necessary to do one of the following to
return to normal operation:
Shut off all lamps and close all doors.
Turn the ignition key to RUN.
This feature will also turn off the parking lamps and
headlamps under most circumstances, if they are left on.
If you would like to turn them back on, turn the exterior
lamps knob.
Accessory Power Outlets
With the accessory power outlets, you can plug in
auxiliary electrical equipment such as a cellular
telephone or CB radio.
The first outlet is located to the right of the cigarette
lighter on the instrument panel. The second outlet
is located on the rear of the center console.
Remove the cover from the outlet to use the outlet. Be
sure to put the cover back on when not using the
accessory power outlet.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adaptor fuses. If you experience a
problem, see your dealer for additional information
on the accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the
equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-18
Ashtrays and Cigarette Lighter
Your vehicle may have this feature. The ashtray is
removable and fits into the front cupholder.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
To remove the ashtray, pull the covered bin out of the
cupholder.
To use the lighter, press it in all the way, and let go.
When it’s ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating. Do not
use anything other than the cigarette lighter in the
heating element.
Climate Controls
Dual Automatic Climate Control
System
With this system you can control the heating, cooling
and ventilation for your vehicle. When your vehicle
is first started and the climate control system is on, or if
the climate control system has been turned on, the
display will show the driver’s temperature setting for
five seconds. Then it will show the outside temperature.
3-19
A. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-20
.
B. Engine Coolant Recovery Tank. See
Cooling System
on page 5-29
.
C. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-36
.
D. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-35
.
E. Automatic Transmission Fluid Dipstick (Out of View).
See “Checking the Fluid Level” under
Automatic
Transmission Fluid on page 5-22
.
F. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-16
.
G. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-27
.
H. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
I. Remote Negative (
) Terminal (Marked GND). See
Jump Starting on page 5-41
.
J. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-37
.
K. Battery. See
Battery on page 5-40
.
L. Engine Compartment Fuse Block. See
Engine
Compartment Fuse Block on page 5-93
.
5-13
A. Engine Coolant Recovery Tank. See
Cooling System
on page 5-29
.
B. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-20
.
C. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-36
.
D. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-16
.
E. Automatic Transmission Fluid Dipstick. See
“Checking the Fluid Level” under
Automatic
Transmission Fluid on page 5-22
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
G. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-27
.
H. Remote Negative (
) Terminal (Marked GND). See
Jump Starting on page 5-41
.
I. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-35
.
J. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-37
.
K. Engine Compartment Fuse Block. See
Engine
Compartment Fuse Block on page 5-93
.
L. Battery. See
Battery on page 5-40
.
5-15
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and
the damage wouldn’t be covered by your warranty.
Some add-on electrical equipment can keep other
components from working as they should.
Your vehicle has an airbag system. Before attempting to
add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-60
.
Headlamps
The headlamp wiring is protected by four fuses. An
electrical overload will cause a lamp to go on and off. If
this happens, have your headlamp wiring checked
right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow or ice, the wiper will stop until the motor cools.
If the overload is caused by some electrical problem, be
sure to get it fixed.
Power Windows and Other Power
Options
Circuit breakers protect the power windows and other
power accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting the
circuit until the problem is fixed or goes away.
5-92
Fuses
Usage
1
Electrically-Controlled Air
Suspension
2
Passenger’s Side High-Beam
Headlamp
3
Passenger’s Side Low-Beam
Headlamp
4
Back-Up-Trailer Lamps
5
Driver’s Side High-Beam Headlamp
6
Driver’s Side Low-Beam Headlamp
7
Rear Window Washer
8
Automatic Transfer Case
9
Windshield Washer
10
Powertrain Control Module B
11
Fog Lamps
12
Stoplamp
13
Cigarette Lighter
14
Ignition Coils
15
Electric Adjustable Pedal
Fuses
Usage
16
Truck Body Controller, Ignition 1
17
Crank
18
Airbag
19
Trailer Electric Brake
20
Cooling Fan
21
Horn
22
Ignition E
23
Electronic Throttle Control
24
Instrument Panel Cluster, Driver
Information Center
25
Automatic Shift Lock Control System
26
Engine 1
27
Back-Up
28
Powertrain Control Module 1
29
Oxygen Sensor
30
Air Conditioning
31
Truck Body Controller
5-95
Fuses
Usage
32
Trailer
33
Anti-lock Brakes (ABS)
34
Ignition A
35
Blower Motor
36
Ignition B
50
Passenger’s Side Trailer Turn
51
Driver’s Side Trailer Turn
52
Hazard Flashers
53
Headlamp Driver Module
54
Air Injection Reactor (AIR) Solenoid
56
Air Injection Reactor (AIR) Pump
Relays
Usage
37
Blank or Headlamp Washer
38
Rear Window Washer
Fuses
Usage
39
Fog Lamps
40
Horn
41
Fuel Pump
42
Windshield Washer
43
High-Beam Headlamp
44
Air Conditioning
45
Cooling Fan
46
Headlamp Driver Module
47
Starter
49
Electric Adjustable Pedal
55
Air Injection Reactor (AIR) Solenoid
Miscellaneous
Usage
48
Instrument Panel Battery
5-96
Fuses
Usage
1
Electrically-Controlled Air
Suspension
2
Passenger’s Side High-Beam
Headlamp
3
Passenger’s Side Low-Beam
Headlamp
4
Back-Up-Trailer Lamps
5
Driver’s Side High-Beam Headlamp
6
Driver’s Side Low-Beam Headlamp
7
Rear Window Washer
8
Automatic Transfer Case
9
Windshield Washer
10
Powertrain Control Module B
11
Fog Lamps
12
Stoplamp
13
Cigarette Lighter
14
Ignition Coils
15
Canister Vent
16
Truck Body Controller, Ignition 1
17
Crank
18
Airbag
19
Trailer Electric Brake
20
Cooling Fan
21
Horn
Fuses
Usage
22
Ignition E
23
Electronic Throttle Control
24
Instrument Panel Cluster, Driver
Information Center
25
Automatic Shift Lock Control System
26
Engine 1
27
Back-Up
28
Powertrain Control Module 1
29
Powertrain
30
Air Conditioning
31
Injector Bank A
32
Trailer
33
Anti-lock Brakes (ABS)
34
Ignition A
35
Blower Motor
36
Ignition B
50
Passenger’s Side Trailer Turn
51
Driver’s Side Trailer Turn
52
Hazard Flashers
53
Transmission
54
Oxygen Sensor Bank B
55
Oxygen Sensor Bank A
56
Injector Bank B
57
Headlamp Driver Module
5-98
Fuses
Usage
58
Truck Body Controller 1
59
Electric Adjustable Pedal
Relays
Usage
37
Headlamp Washer
38
Rear Window Washer
39
Fog Lamps
40
Horn
41
Fuel Pump
42
Windshield Wipers/Washer
43
High-Beam Headlamp
44
Air Conditioning
45
Cooling Fan
46
Headlamp Driver Module
47
Starter
49
Electric Adjustable Pedal
60
Powertrain
Miscellaneous
Usage
48
Instrument Panel Battery
Rear Underseat Fuse Block
5-99
Fuses
Usage
01
Right Door Control Module
02
Left Door Control Module
03
Endgate Module 2
04
Truck Body Controller 3
05
Rear Fog Lamps
06
Blank
07
Truck Body Controller 2
08
Power Seats
09
Rear Wiper
10
Driver Door Module
11
Amplifier
12
Passenger Door Module
13
Rear Climate Controls
14
Left Rear Parking Lamps
15
Blank
16
Vehicle Center High-Mounted Stop
Lamp
17
Right Rear Parking Lamps
18
Locks
19
Liftgate Module/Driver Seat Module
20
Blank
21
Lock
23
Blank
24
Unlock
5-100
Fuses
Usage
25
Blank
26
Blank
27
OnStar
®
Overhead Battery, OnStar
®
System
28
Sunroof
29
Rainsense™ Wipers
30
Parking Lamps
31
Truck Body Controller Accessory
32
Truck Body Controller 5
33
Front Wipers
34
Vehicle Stop
35
Transmission Control Module
36
Heat Ventilation Air Conditioning B
37
Front Parking Lamps
38
Left Turn Signal
Fuses
Usage
39
Heat Ventilation Air Conditioning I
40
Truck Body Controller 4
41
Radio
42
Trailer Park
43
Right Turn Signal
44
Heat Ventilation Air Conditioning
45
Rear Fog Lamps
46
Auxiliary Power 1
47
Ignition 0
48
Four-Wheel Drive
49
Blank
50
Truck Body Controller Ignition
51
Brakes
52
Truck Body Controller Run
5-101