Buick Park Avenue - 2005 Fuse Box Diagram

Buick Park Avenue - 2005 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
If a door is opened without the key or the remote
keyless entry transmitter, the alarm will go off. Your
vehicle’s lamps will flash and the horn will sound
for 30 seconds. The lamps and horn will then turn off to
save battery power.
Remember, the theft-deterrent system won’t activate if
you lock the doors with a key or use the manual
door lock. It activates only if you use a power door lock
switch with the door open, or with the remote keyless
entry transmitter. You should also remember that
you can start your vehicle with the correct key if the
alarm has been set off.
Here’s how to avoid setting off the alarm by accident:
If you do not want to activate the theft-deterrent
system, the vehicle should be locked with the
door key
after
the doors are closed.
Always unlock a door with a key, or use the remote
keyless entry transmitter. Unlocking a door any
other way will set off the alarm.
If you set off the alarm by accident, unlock any door
with your key. You can also turn off the alarm by
pressing the unlock button on the remote keyless entry
transmitter. The alarm won’t stop if you try to unlock
a door any other way.
Testing the Alarm
The alarm can be tested by following these steps:
1. From inside the vehicle, roll down the driver’s
window and open the driver’s door.
2. Activate the system by locking the doors using the
power door lock switch while the door is open, or
using the remote keyless entry transmitter.
3. Get out of the car, close the door and wait for the
SECURITY light to go out.
4. Then reach in through the window, unlock the door
with the manual door lock and open the door. This
should set off the alarm.
If the alarm does not sound when it should, but the
vehicle’s lamps flash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse,
see
Fuses and Circuit Breakers on page 5-92
.
If the alarm does not sound or the vehicle’s lamps do
not flash, the vehicle should be serviced by a GM dealer.
2-19
If the engine still does not start, and the key appears to
be undamaged, try another key. At this time, you
may also want to check the fuse. See
Fuses and Circuit
Breakers on page 5-92
. If the engine still does not
start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty. See
your dealer who can service the PASS-Key
®
III to
have a new key made.
It is possible for the PASS-Key
®
III decoder to learn the
transponder value of a new or replacement key. Up
to 10 additional keys may be programmed for the
vehicle. This procedure is for programming additional
keys only.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS-Key
®
III to
have new keys made. To program additional keys you
will need two current driver’s keys. You must add a step
to the following procedure. After Step 2, repeat
Steps 1 and 2 with the second current driver’s key. Then
continue with Step 3.
To program the new key, do the following:
1. Verify that the new key has PK3 stamped on it.
2. Insert the current driver’s key in the ignition
and start the engine. If the engine will not start, see
your GM dealer for service.
3. After the engine has started, turn the ignition to
OFF, and remove the key.
4. Insert the key to be programmed and turn it to RUN
within 10 seconds of removing the previous key.
5. The SECURITY light will turn off once the key has
been programmed. It may not be apparent that the
SECURITY light went on due to how quickly the
key is programmed.
6. Repeat Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the SECURITY light comes
on and stays on, you will be able to restart your
engine if you turn it off. Your PASS-Key
®
III system,
however, is not working properly and must be serviced
by your GM dealer. Your vehicle is not protected by
the PASS-Key
®
III system at this time.
If you lose or damage a PASS-Key
®
III, see your
GM dealer to have a new key made.
2-21
If your vehicle is equipped with the Head-Up Display
(HUD), an arrow will also appear in the display area to
indicate the direction of the turn or lane change.
See
Head-Up Display (HUD) on page 3-19
for
more information.
You may also have an arrow in the outside mirror that
flashes when the turn signal is used. See
Outside Power
Mirrors on page 2-37
for more information.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by itself
when you release it.
As you signal a turn or a lane change, if the arrows
flash at twice the normal rate, this may indicate that a
signal bulb may be burned out and other drivers will not
see your turn signal. If a bulb is burned out, replace
it to help avoid an accident.
If the arrows do not go on at all when you signal a turn,
check the fuse and check for burned-out bulbs. See
Fuses and Circuit Breakers on page 5-92
.
If you have a trailer towing option with added wiring for
the trailer lamps, the signal indicator will flash even
if a turn signal bulb is burned out. Check the front and
rear turn signal lamps regularly to make sure they
are working. You do not need to add a different flasher.
Turn Signal On Chime
If your turn signal is left on for more than three-quarters
of a mile (1.2 km), a chime will sound at each flash
of the turn signal. To turn off the chime, move the turn
signal lever to the off position.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high
beam or high beam to low beam, pull the turn signal
lever toward you and release it.
While the high beams are
on, this light located on the
instrument panel cluster
will also be on.
If your vehicle is equipped with the Head-Up
Display (HUD), this symbol will also appear in the
display area to indicate the high beams are on.
See
Head-Up Display (HUD) on page 3-19
for
more information.
3-8
2. Adjust the seat to a comfortable driving position.
Keep pressing the top arrow on the image height
adjuster to raise the image as far as possible.
3. Keep pressing the bottom arrow on the image
height adjuster to move the image as low as
possible, while still keeping it in full view.
4. Slide the dimmer switch downward until the HUD
image is no brighter than necessary.
To turn the HUD display off, slide the dimmer switch all
the way down.
If the sun comes out, the sky becomes cloudy, or if
you turn your headlamps on, you may need to
adjust the HUD brightness using the dimmer switch.
Polarized sunglasses could make the HUD
image harder to see.
To change the display from English to metric units,
push the ENG/MET button located to the left of
the steering column.
Care of the HUD
Clean the inside of the windshield as necessary to
remove any dirt or film that reduces the sharpness or
clarity of the HUD image.
To clean the HUD lens, spray GM Glass Cleaner or a
liquid household glass cleaner on a soft, clean cloth.
Gently wipe and dry the HUD lens. Do not spray
cleaner directly on the lens to avoid cleaner leaking
inside the unit.
If You Can’t See The HUD Image When
the Ignition is On
If the ignition is on and you can’t see the HUD image,
check to see if:
The headlamps are on.
Something is covering the HUD unit.
The HUD dimmer control is adjusted properly.
The HUD image is adjusted to the proper height.
A fuse is blown. See
Fuses and Circuit Breakers on
page 5-92
.
Keep in mind that your windshield is part of the HUD
system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD
or your HUD image may look blurred or out of focus.
3-21
Accessory Power Outlets
The accessory power outlets can be used to plug in
electrical equipment such as a cellular telephone or
CB radio.
Your vehicle has two power outlets located in the rear
storage area of the front center console. See
Center
Console Storage Area on page 2-46
for more
information on location.
Your vehicle may have a small cap that must be pulled
down to access the accessory power outlet. If it
does, when not using the outlet be sure to cover it with
the protective cap.
The accessory power outlets will only operate while the
ignition key is in RUN and for 10 minutes after turning
the ignition off. If you would like to operate an accessory
for an extended period of time, contact your dealer for
more information.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible to
the accessory power outlet and could result in blown
vehicle or adapter fuses. If you experience a problem
see your dealer for additional information on accessory
power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to
follow the proper installation instructions included with
the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-24
Ashtrays and Cigarette Lighter
The front ashtray is located under the climate control
panel on the center console. Press on the door to
release the ashtray. To close, press on the door again.
To empty the ashtray, remove it from the center
console by gripping the edges and pulling straight out.
To reinstall, push the tray back into place.
The rear ashtrays are located on each rear door panel.
To remove a rear ashtray, open the lid and ease the
ashtray upward until the edge can be grasped to pull the
ashtray up and out.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in
the ashtray.
There is a cigarette lighter near the front ashtray. To
use it, push it in all the way and let go. When it’s ready,
it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
Climate Controls
Dual Automatic Climate
Control System
With this system you can control the heating, cooling
and ventilation for your vehicle.
3-25
A. Battery. See
Battery on page 5-40
.
B. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-95
.
C. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-26
.
D. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-13
.
E. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-13
.
F. Engine Coolant Air Bleed Valve. See “How to Add
Coolant to the Radiator” under
Cooling System
on page 5-28
.
G. Automatic Transaxle Fluid Dipstick. See “Checking
the Fluid Level” under
Automatic Transaxle Fluid
on page 5-22
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-37
.
I. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-35
.
J. Engine Coolant Recovery Tank. See
Cooling System
on page 5-28
.
K. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-19
.
Engine Oil
If the DIC message, ENGINE OIL LOW — CHECK
LEVEL appears on the instrument cluster, it means you
need to check your engine oil level right away. For
more information, see
Driver Information Center (DIC)
on page 3-46
.
You should check your engine oil level regularly; this is
an added reminder.
Checking Engine Oil
It is a good idea to check your engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop. See
Engine Compartment Overview on page 5-12
for
the location of the engine oil dipstick.
5-13
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of fires
caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
If you ever have a problem on the road and don’t have
a spare fuse, you can borrow one that has the same
amperage. Just pick some feature of your vehicle
that you can get along without — like the radio or
cigarette lighter— and use its fuse, if it is the correct
amperage. Replace it as soon as you can.
Main Instrument Panel Fuse Block
The main instrument panel fuse block is located
under the instrument panel, on the passenger’s side of
the vehicle. Lamps, connectors and the HVAC duct
temperature sensors may need to be disconnected and
removed to allow access to this fuse block.
Remove the hush panel on the passenger’s side to
reveal the fuses by performing the following steps:
1. Remove the two screws located along the front
edge of the panel.
2. Lower the hush panel.
3. Remove the fuse block cover.
4. Place the wide end of the fuse puller over the
plastic end of the fuse.
5. Squeeze the ends over the fuse and pull it out.
When finished, reinstall the fuse block cover and
the hush panel. Reinstall lamps, connectors and HVAC
duct temperature sensors if they were removed.
5-92
Fuses
Usage
SBM
Interior Lamps
PDM
PDM Module
A/C
HVAC Motor, HVAC Mix Motors
IGN SEN
Auto Dimming Mirror, Driver HTS
Seat, Rear Defog Relay, MEM
Module, Cool LVL Sensor,
Passenger Heated Seat
ELC
HVAC Flat Pk Mtrs, Electronic Level
Control Sensor, Electronic Level
Control Sensor (Rear Fuse Block)
Fuses
Usage
ABS
Anti-Lock Brake System Module
HVAC
HVAC Main Con Head,
HVAC Programmer, Instrument
Panel Cluster
CR CONT
Stepper Motor Cruise, Cruise Switch
HUD
Head-Up Display Switch,
Head-Up Display
CSTR/SBM
HVAC Programmer, Instrument
Panel Cluster, SBM (275 to LCM)
(1135 to BTSI SL)
LP PK L
Underhood Lamp, Left
Park/Sidemarker, Left Park/Turn
Lamp, SBM, Left Tail Signal
Lamp, Left Tail/Stoplamp, Left
Rear Sidemarker
LP PK R
Right Park/Sidemarker Lamp, Right
Park/Turn Lamp, Right Tail/Sign
Lamp, Right Tail/Stoplamp, Right
Rear Sidemarker, Stop/Taillamp,
Tail/Signal Lamp, License
Lamp, RFA
RUN
Run/Accessory
WSW
Wiper Motor
Blank
Not Used
WSW/RFA
Wiper Switch, RFA, Rain Sense
B/U LP
Auto Dimming Mirror,
Back-Up Lamps
5-93
Auxiliary Instrument Panel
Fuse Block
The auxiliary instrument panel fuse block is located
under the instrument panel, on the passenger’s side of
the vehicle. Lamps, connectors and the HVAC duct
temperature sensors may need to be disconnected and
removed to allow access to this fuse block.
Remove the hush panel on the passenger’s side to
reveal the fuses by performing the following steps:
1. Remove the two screws located along the front
edge of the panel.
2. Lower the hush panel.
3. Remove the fuse block cover.
4. Place the wide end of the fuse puller over the
plastic end of the fuse.
5. Squeeze the ends over the fuse and pull it out.
When finished, reinstall the fuse block cover and
the hush panel. Reinstall lamps, connectors and HVAC
duct temperature sensors if they were removed.
Fuses
Usage
PERIM LP
Perimeter Lamps
ACCY
Accessory
IGN 3
Ignition 3
5-94
Fuses
Usage
11
Spare
12
Injectors #1-6
13
C-31
14
Right High Beam
15
Spare
16
Left High Beam
17
Spare
18
Right Low Beam
19
Left Low Beam
20
Stop
21
Fuel Pump Relay (Wire in BEC)
22
Run/Crank
23
Powertrain Control Module
24
Parking Lamps
25
Hazard Flashers
26
Spare
27
Spare
28
ABS #2
Relays
Usage
29
Ignition
30
Horn
31
Cooling Fan 1
Relays
Usage
32
Starter
33
Not Used
34
Cooling Fan SP
35
Cooling Fan 2
36
Air Conditioning Clutch
37
Fuel Pump
Fuses
Usage
38
Bat #1
39
Blower Motor
40
Cooling Fan 1
41
Headlamp
42
BAT #2
43
Ignition
44
Starter
45
ABS
46
Fuse Puller
5-96
Rear Compartment Fuse Block
Additional fuses are located in the fuse center under the
rear seat. The rear seat cushion must be removed to
access the fuses. See “Removing the Rear Seat
Cushion” following for more information.
Relays
Usage
1
Heated Backlite
2
Retained Accessory Power (RAP)
3
Trunk Release
4
Electronic Level Control
Circuit
Breakers
Usage
5
Power Seat
6
Electronic Level Control Sensor,
Electronic Level Control
Compressor Solenoid
Fuses
Usage
7
Crank
8
Accessory Outlet
9
Powertrain Control Module for Cruise
10
SBM Module
11
Radio/Phone
12
Sunroof
13
Spare
14
CD Changer, Phone
15
Driver Door Module
16
Spare
17
Radio
18
Driver Heated Seat Module
19
Rear Door Module
20
Trunk Release
21
Spare
22
Instrument Panel Ashtray
Cigarette Lighter
5-97
Fuses
Usage
23
Spare
24
Spare
25
Passenger Heated Seat Module
26
Right Rear Cig Lighter
27
Left Rear Cig Lighter
28
RFA, Memory Seat Module, Driver
Seat Switch
Removing the Rear Seat Cushion
Notice:
If, when removing or reinstalling the rear
seat, you do not do it carefully, you could damage
the fuse center. Avoid contact between the rear seat
and the fuse center whenever you remove or
reinstall the rear seat.
To remove the rear seat cushion, do the following:
1. Pull up on the front of the cushion to release the
front hooks.
2. Pull the cushion up and out toward the front of
the vehicle.
To reinstall the rear seat cushion, do the following:
{
CAUTION:
A safety belt that is not properly routed
through the seat cushion or is twisted will not
provide the protection needed in a crash. If the
safety belt has not been routed through the
seat cushion at all, it will not be there to work
for the next passenger. The person sitting in
that position could be badly injured. After
reinstalling the seat cushion, always check to
be sure that the safety belts are properly
routed and are not twisted.
5-98