Buick Rendezvous - 2004 Fuse Box Diagram

Buick Rendezvous - 2004 Fuse Box Diagram

These are some examples of vehicle symbols you may find on your vehicle:
v
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse. See
Fuses
and Circuit Breakers on page 5-109
. If the engine still
does not start with the other key, your vehicle needs
service. If your vehicle does start, the first key may be
faulty. See your dealer who can service the
PASS-Key
®
III to have a new key made.
It is possible for the PASS-Key
®
III decoder to program
the transponder value of a new or replacement key.
Up to 10 additional keys may be programmed for
the vehicle. This procedure is for programming additional
keys only. If all the currently programmed keys are
lost or do not operate, you must see your dealer or a
locksmith who can service PASS-Key
®
III to have
keys made and programmed to the system.
See your dealer who can service PASS-Key
®
III to get a
new key blank that is a cut exactly as the ignition key
that operates the system.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS-Key
®
III to
have new keys made. To program additional keys you
will need two current driver’s keys (black in color).
You must add a step to the following procedure. After
Step 3 repeat Steps 1 through 3 with the second current
driver’s key. Then continue with Step 4.
To program the new PK3
®
key do the following:
1. Verify the new key has PK3
®
stamped on it.
2. Insert the original key in the ignition and start the
engine. If the engine will not start, see your dealer
for service.
3. After the engine has started, turn the key to OFF,
and remove the key.
4. Insert the key to be programmed and turn it to ON
within 10 seconds of removing the previous key.
5. The SECURITY message will turn off once the key
has been programmed. It may not be apparent that
the SECURITY message went on due to how
quickly the key is programmed.
6. Repeat Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the SECURITY message
comes on and stays on, you will be able to restart your
engine if you turn it off. Your PASS-Key
®
III system,
however, is not working properly and must be serviced
by your dealer. Your vehicle is not protected by the
PASS-Key
®
III system at this time.
If you lose or damage a PASS-Key
®
III key, see your
dealer who can service PASS-Key
®
III to have a
new key made.
2-18
The main components of the instrument panel are the
following:
A. Exterior/Interior Lamps Control. See
Exterior Lamps
on page 3-14
and
Interior Lamps on page 3-16
.
B. Turn Signal/Multifunction Lever. See
Turn
Signal/Multifunction Lever on page 3-8
.
C. Hazard Warning Flasher Switch. See
Hazard
Warning Flashers on page 3-6
.
D. Instrument Panel Cluster. See
Instrument Panel
Cluster on page 3-40
.
E. Shift Lever. See
Automatic Transaxle Operation on
page 2-23
.
F. Instrument Panel Outlets. See
Outlet Adjustment on
page 3-38
.
G. Audio System. See
Audio System(s) on page 3-73
.
H. Audio Steering Wheel Controls. See
Audio
Steering Wheel Controls on page 3-129
.
I. Head-Up Display Switch and Driver Information
Center (DIC) Controls. See
Head-Up Display (HUD)
on page 3-21
and
DIC Controls and Displays on
page 3-62
.
J. Hood Release. See
Hood Release on page 5-11
.
K. Ignition Switch. See
Ignition Positions on page 2-20
.
L. Climate Controls. See
Climate Control System on
page 3-28
,
Dual Climate Control System on
page 3-32
or
Dual Automatic Climate Control System
on page 3-35
.
M. Instrument Panel Switchbank. See
Instrument Panel
Switchbank on page 3-21
.
N. Front Armrest Storage. See
Front Armrest Storage
Area on page 2-40
.
O. Ashtray/Cigarette Lighter/Accessory Power
Outlet/Cell Phone Storage/Purse
Storage/Cupholders. See
Ashtrays and Cigarette
Lighter on page 3-28
,
Accessory Power Outlets on
page 3-27
,
Cell Phone Storage Area on page 2-39
,
Floor Console Storage Area on page 2-40
and
Cupholder(s) on page 2-39
.
P. Floor Console Fuse Block. See
Fuses and Circuit
Breakers on page 5-109
.
Q. Glove Box. See
Glove Box on page 2-39
.
3-5
When you first start the vehicle the display will show
BUICK and the Buick logo for a few seconds. If it is cold
outside, this display may stay on for up to a minute.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity
of the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry
it. Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you cannot see the HUD image,
check to see if one of the following conditions exist:
The HUD unit is covered
The HUD dimmer knob is adjusted incorrectly
The HUD image is not adjusted to the proper height
Ambient light in the direction your vehicle is
facing, is low
A fuse is blown. See
Fuses and Circuit Breakers on
page 5-109
.
If you ever have to have your windshield replaced, be
sure to get one that is designed for the HUD or your
HUD image may look blurred and out of focus.
Ultrasonic Rear Parking Assist
(URPA)
The Ultrasonic Rear Parking Assist (URPA) system is
designed to help you park, while the vehicle is in
REVERSE (R). It operates only at very low speeds, less
than 3 mph (5 km/h). URPA can help make parking
easier and to help you avoid colliding with objects such as
parked vehicles. The URPA system can detect objects up
to 5 feet (1.5 m) behind the vehicle, and tell you how
close these objects are from your rear bumper.
Your vehicle’s URPA operates when the shift lever is
moved into REVERSE (R) and the vehicle speed is less
than 3 mph (5 km/h). Four ultrasonic sensors located at
the rear bumper are used to detect the distance to the
object. The URPA display is located inside the vehicle,
near the rear window. It has three color-coded lights used
to provide distance and system information to the driver.
3-24
Accessory Power Outlets
With accessory power outlets you can plug in electrical
equipment such as a cellular telephone or CB radio.
There is one front power outlet/cigarette lighter located
on the floor console in the cell phone storage
compartment.
There are also two rear power outlets. One is located in
the rear of the floor console below the vents. The
other is located in the rear of the vehicle on the driver’s
side behind the access door.
Pull the cover down to use an accessory power outlet.
When not in use, always cover the accessory power
outlets with the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on the accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the
equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-27
Ashtrays and Cigarette Lighter
The ashtray is located on the floor console closest to
the instrument panel. Lift the lid to expose the ashtray.
To remove the ashtray, lift it up.
The cigarette lighter is located on the floor console in
the cell phone storage compartment closest to the
driver’s seat. Lift the lid to expose the cigarette lighter.
To use the lighter, push it in all the way and let go.
When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
Climate Controls
Climate Control System
With this system you can control the heating, cooling,
and ventilation for your vehicle.
3-28
A. Underhood Fuse Block. See
Fuses and Circuit
Breakers on page 5-109
.
B. Remote Positive (+) Terminal. See
Jump Starting on
page 5-43
.
C. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-36
.
D. Automatic Transaxle Fluid Dipstick. See
Automatic
Transaxle Fluid on page 5-21
.
E. Brake Master Cylinder. See
Brakes on page 5-38
.
F. Windshield Washer Fluid Reservoir. See
Windshield
Washer Fluid on page 5-37
.
G. Battery. See
Battery on page 5-42
.
H. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-25
.
I. Engine Oil Fill Cap. See
Engine Oil on page 5-14
.
J. Engine Oil Dipstick. See
Engine Oil on page 5-14
.
K. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-19
.
L. Coolant Recovery Tank. See
Engine Coolant on
page 5-23
.
5-13
4. Open the hoods and locate the batteries. Find the
positive (+) and negative (
) terminals on each
vehicle.
You will not need to access your battery for jump
starting. Your vehicle has a remote positive (+) jump
starting terminal for that purpose. The terminal is
located under a tethered cap at the front of the
underhood fuse and relay center. See
Engine
Compartment Overview on page 5-12
for more
information on location.
Flip the cap up to access the remote positive (+)
terminal. You should always use the remote
positive (+) terminal instead of the positive (+)
terminal on the battery.
{
CAUTION:
An electric fan can start up even when the
engine is not running and can injure you. Keep
hands, clothing and tools away from any
underhood electric fan.
{
CAUTION:
Using a match near a battery can cause battery
gas to explode. People have been hurt doing
this, and some have been blinded. Use a
flashlight if you need more light.
Be sure the battery has enough water. You do
not need to add water to the ACDelco
®
battery
installed in your new vehicle. But if a battery
has filler caps, be sure the right amount of
fluid is there. If it is low, add water to take care
of that first. If you do not, explosive gas could
be present.
Battery fluid contains acid that can burn you.
Do not get it on you. If you accidentally get it
in your eyes or on your skin, flush the place
with water and get medical help immediately.
5-44
{
CAUTION:
Inflating something too much can make it
explode, and you or others could be injured.
Be sure to read the inflator instructions, and
inflate any object only to its recommended
pressure.
To use your accessory inflator system, do the following:
1. Turn the ignition to ACCESSORY or ON.
2. Attach the appropriate nozzle adapter, if required,
to the end of the hose that has the pressure gage.
3. Attach that end of the hose to the object you wish
to inflate.
4. Remove the protective cap covering the outlet.
5. Attach the other end of the hose to the outlet.
6. Press the accessory inflator switch. The light in the
switch will come on to show the system is working.
If the accessory inflator system does not turn on or the
light does not come on, the fuse may be blown or
installed incorrectly. See
Fuses and Circuit Breakers on
page 5-109
or see your dealer for service.
Your accessory inflator will automatically shut off after
about 10 minutes. The light in the switch will blink. After
about one minute you can use the system again. Press
the inflator switch and the indicator light will come on.
Notice:
If you run the accessory inflator longer than
30 minutes at a time, you could damage the
inflator. The repairs would not be covered by your
warranty. Run the inflator for short periods of
time only.
After running the accessory inflator for 30 minutes, wait
at least 10 minutes before restarting the accessory
inflator.
To turn off the inflator, do the following:
1. Press the switch and detach the hose, first from the
inflated object, then from the outlet.
2. Put the protective cap back on.
3. Place the inflator kit tools in the pouch, and store in
the glove box.
To put the cover back on, line up the tabs at the back of
the cover and put it in place. Push down the tab to
secure the cover.
5-75
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker and a fuse. If the motor overheats due to
heavy snow, etc., the wiper will stop until the motor
cools. If the overload is caused by some electrical
problem, be sure to get it fixed.
Power Windows and Other Power
Options
Circuit breakers in the floor console fuse block protect
the power windows and other power accessories. When
the current load is too heavy, the circuit breaker
opens and closes, protecting the circuit until the problem
is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
If you ever have a problem on the road and do not have
a spare fuse, you can borrow one that has the same
amperage. Just pick a feature of your vehicle that
you can get along without – like the radio or cigarette
lighter - and use its fuse, if it is the right amperage.
Replace it as soon as you can.
There are two fuse blocks in your vehicle: the floor
console fuse block and the underhood fuse and relay
center.
5-109
Floor Console Fuse Block
The floor console fuse block is located to the left of the
glove box near the floor.
Pull the door open to access the fuse block.
Fuse
Usage
1
Empty
2
Steering Wheel Radio Controls
3
Power Door Locks
4
Empty
5
Empty
6
Empty
7
Empty
8
Empty
9
Empty
10
Turn Signal and Hazard Lamp
Flashers
5-110
Fuse
Usage
11
Power Seats
12
Electronic Level Control (ELC)
Compressor
13
Liftgate and Endgate
14
Rear Auxiliary Power Outlet
15
Electronic Level Control (ELC)
Compressor Relay and Height
Sensor
16
Heated Mirrors
17
Power Mirrors
18
Ignition 1 Module
19
Turn Signal Switch
21
Rear Defogger
22
Air Bag Module
24
TCC Switch
25
HVAC Blower Motor
26
HVAC Mode and Temperature
Motors and Head-Up Display
28
Not Used
29
Windshield Wipers and Washer
30
Instrument Panel Cluster, Body
Control Module (BCM),
PASS-Key
®
III
31
Park Lock Ignition Key Solenoid
Fuse
Usage
32
Rear Window Wiper/Washer
34
Power Sunroof
35
Power Windows
36
Map Lamps, Courtesy Lamps and
Instrument Panel Lights
37
Radio
38
UQ3 Radio Amplifier
39
Head-Up Display
40
Hazard Flashers
41
Instrument Panel Cluster, Climate
Control, Security LED and Remote
Keyless Entry Mode
42
PASS-Key
®
III
44
Body Control Module (BCM)
Relay
Usage
20
Rear Defogger Relay
23
Ignition Relay
27
Accessory Relay
33
Retained Accessory Power Relay
43
Accessory Diode
5-111
Underhood Fuse Block
This fuse block is located in the engine compartment,
on the passenger’s side of the vehicle. See
Engine
Compartment Overview on page 5-12
for more
information on location.
The back-up lamp relay (A) is located to the left of the
underhood fuse block.
To remove the cover, press the two tabs in and lift up
the cover.
5-112
Fuse
Usage
1
Fuel Pump
2
Air Conditioning Compressor Clutch
3
Horn
4
Engine Controls-Emissions and
Sensors
5
Power Control Module
(PCM)-Battery Power
6
Anti-Lock Brakes (ABS) Control
Module
7
Transaxle Solenoids
9
Anti-lock Brake System (ABS)
Solenoid Valves
10
Oxygen Sensors-Emissions Control
11
Injectors
13
Engine Controls
14
Daytime Running Lamps (DRL)
15
Passenger’s Low-Beam Headlamp
17
Driver’s Low-Beam Headlamp
18
Driver’s High-Beam Headlamp
19
Ignition Switch Battery Power
Fuse
Usage
20
Parking Lamps-Front and Rear
23
Passenger’s High-Beam Headlamp
24
Vent Solenoids
25
DVD
26
Front Fog Lamps
27
Ignition Relay, Neutral Start Switch,
Powertrain Control Module (PCM)
28
Body Control Module-Battery Power
29
S Band, Remote Digital Radio
Receiver
30
All-Wheel Drive (AWD) Module
31
Cruise Control
32
Front Power Outlets/Lights, OnStar
®
33
Automatic Transaxle Shift Lock
Control System
35
Starter Solenoid Battery Fuse
36
Anti-lock Brake System (ABS) Motor
39
Engine Cooling Fan
40
Engine Cooling Fan
5-113
Fuse
Usage
41
Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
42
Main Battery Fuse for Heated Seats,
Air
45
Main Battery Fuse for Power
Outlets, Level Control, Power Seats
and Mirrors and Body Computer
47
Main Battery Fuse for Climate
Control Blower and Ignition 3 Relay
48
Main Battery Fuse for Ignition
Switch, Radio, Heads-Up Display,
Remote Keyless Entry (RKE),
Instrument Cluster, Air Conditioning
and Body Computer
70
§
Diode for Air Conditioning
Compressor Clutch
Relay
Usage
A
Back-Up Lamps
50
Horn
51
Fuel Pump
52
Air Conditioning Clutch
53
Daytime Running Lamps (DRL)
54
Low-Beam Headlamps
55
Parking Lamps
56
High-Beam Headlamps
57
Fog Lamps
58
Starter Relay
59
Cooling Fan
60
Ignition 1 Relay
61
Cooling Fan
62
Cooling Fan
63
Empty
5-114