Buick Rainier - 2004 Fuse Box Diagram

Buick Rainier - 2004 Fuse Box Diagram

These are some examples of symbols you may find on your vehicle:
v
Remember, the theft-deterrent system won’t activate
if you lock the doors with a key or use the manual door
lock. It activates only if you use a power door lock
switch with the door open, or with the remote keyless
entry transmitter. You should also remember that
you can start your vehicle with the correct ignition key
if the alarm has been set off.
Here’s how to avoid setting off the alarm by accident:
If you don’t want to activate the theft-deterrent
system, the vehicle should be locked with the
door key
after
the doors are closed.
Always unlock a door with a key, or use the remote
keyless entry transmitter. Unlocking a door any
other way will set off the alarm.
If you set off the alarm by accident, unlock any door
with the key. You can also turn off the alarm by pressing
unlock on the remote keyless entry transmitter.
The alarm won’t stop if you try to unlock a door any
other way.
Testing the Alarm
The alarm can be tested by following these steps:
1. From inside the vehicle, lower the driver’s window
and open the driver’s door.
2. Activate the system by locking the doors with the
power door lock switch while the door is open,
or with the remote keyless entry transmitter.
3. Get out of the vehicle, close the door and wait
for the security light to go out.
4. Then reach in through the window, unlock the
door with the manual door lock and open the
door. This should set off the alarm.
When the alarm is set the power door unlock switch
is not operational.
If the alarm does not sound when it should but the
headlamps flash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse,
see
Fuses and Circuit Breakers on page 5-103
.
If the alarm does not sound or the headlamps do not
flash, the vehicle should be serviced by your dealer.
2-18
Passlock
®
Your vehicle is equipped with the Passlock
®
theft-deterrent system.
Passlock
®
is a passive theft-deterrent system that
enables fuel if the ignition lock cylinder is turned with
a valid key. If a correct key is not used or the ignition
lock cylinder is tampered with, the fuel system is
disabled and the vehicle will not start.
During normal operation, the security light will turn off
approximately five seconds after the key is turned
to RUN.
If the engine stalls and the security light flashes, wait
about 10 minutes until the light stops flashing before
trying to restart the engine. Remember to release
the key from START as soon as the engine starts.
If the engine does not start after three tries, the vehicle
needs service.
If the engine is running and the security light comes on,
you will be able to restart the engine if you turn the engine
off. However, your Passlock
®
system is not working
properly and must be serviced by your dealer. Your
vehicle is not protected by Passlock
®
at this time. You
may also want to check the fuse. See
Fuses and Circuit
Breakers on page 5-103
. See your dealer for service.
In an emergency, call the GM Roadside Assistance
Center. See
Roadside Assistance Program on page 7-6
.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:
Your vehicle does not need an elaborate
“break-in.” But it will perform better in the long
run if you follow these guidelines:
Keep your speed at 55 mph (88 km/h) or less
for the first 500 miles (805 km).
Do not drive at any one speed — fast or
slow — for the first 500 miles (805 km).
Do not make full-throttle starts.
Avoid making hard stops for the first 200 miles
(322 km) or so. During this time your new brake
linings are not yet broken in. Hard stops with new
linings can mean premature wear and earlier
replacement. Follow this breaking-in guideline
every time you get new brake linings.
Do not tow a trailer during break-in. See
Towing
a Trailer on page 4-53
for more information.
2-19
Turn and Lane Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, just raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
your lane change. The lever will return by itself when you
release it. The bottom of the outside rearview mirrors may
also be equipped with lane change indicators.
As you signal a turn or a lane change, if the arrows flash
more quickly than normal, a signal bulb may be burned
out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you signal
a turn, check the fuse. See
Fuses and Circuit Breakers
on page 5-103
and check for burned-out bulbs.
If you have a trailer towing option with added wiring
for the trailer lamps, a different turn signal flasher
is used. With this flasher installed, the signal indicator
will flash even if a turn signal bulb is burned out. Check
the front and rear turn signal lamps regularly to make
sure they are working.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the
turn signal. To turn off the chime, move the turn signal
lever to the off position.
3-8
Accessory Power Outlets
With the accessory power outlets, you can plug in
auxiliary electrical equipment such as a cellular
telephone or CB radio.
The first outlet is located to the right of the cigarette
lighter on the instrument panel. The second outlet
is located on the rear of the center console.
Remove the cover from the outlet to use the outlet.
Be sure to put the cover back on when not using the
accessory power outlet.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adaptor fuses. If you experience a
problem, see your dealer for additional information
on the accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow
the proper installation instructions included with
the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not hang
any type of accessory or accessory bracket from the
plug because the power outlets are designed for
accessory power plugs only.
Ashtrays and Cigarette Lighter
Your vehicle may have this feature. The ashtray is
removable and fits into the front cupholder.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
To remove the ashtray, pull the covered bin out of
the cupholder.
To use the lighter, press it in all the way, and let go.
When it’s ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold
a cigarette lighter in while it is heating.
3-19
A. Coolant Recovery Tank.
See
Engine Coolant on page 5-27
.
B. Engine Air Cleaner/Filter.
See
Engine Air Cleaner/Filter
on page 5-23
.
C. Windshield Washer Fluid Reservoir.
See
Windshield Washer Fluid
on page 5-40
.
D. Power Steering Fluid Reservoir.
See
Power Steering Fluid
on page 5-39
.
E. Automatic Transmission Dipstick.
See
Automatic Transmission Fluid
on page 5-24
.
F. Engine Oil Dipstick.
See
Engine Oil on page 5-18
.
G. Radiator Pressure Cap.
See
Radiator Pressure Cap
on page 5-29
.
H. Engine Oil Fill Cap.
See
Engine Oil on page 5-18
.
I. Remote Negative (–) TerminalMarked GND.
See
Jump Starting on page 5-45
.
J. Brake Master Cylinder.
See
Brakes on page 5-41
.
K. Battery.
See
Battery on page 5-44
.
L. Engine Compartment Fuse Block.
See “Engine Compartment Fuse Block” under
Fuses and Circuit Breakers on page 5-103
.
5-15
A. Coolant Recovery Tank.
See
Engine Coolant on page 5-27
.
B. Engine Air Cleaner/Filter.
See
Engine Air Cleaner/Filter
on page 5-23
.
C. Windshield Washer Fluid Reservoir.
See
Windshield Washer Fluid
on page 5-40
.
D. Engine Oil Dipstick.
See
Engine Oil on page 5-18
.
E. Automatic Transmission Dipstick.
See
Automatic Transmission Fluid
on page 5-24
.
F. Engine Oil Fill Cap.
See
Engine Oil on page 5-18
.
G. Radiator Pressure Cap.
See
Radiator Pressure Cap
on page 5-29
.
H. Remote Negative (-) Terminal Marked GND.
See
Jump Starting on page 5-45
.
I. Power Steering Fluid Reservoir.
See
Power Steering Fluid on page 5-39
.
J. Brake Master Cylinder.
See
Brakes on page 5-41
.
K. Engine Compartment Fuse Block.
See “Engine Compartment Fuse block” under
Fuses and Circuit Breakers on page 5-103
.
L. Battery.
See
Battery on page 5-44
.
5-17
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and
the damage wouldn’t be covered by your warranty.
Some add-on electrical equipment can keep other
components from working as they should.
Your vehicle has an air bag system. Before attempting
to add anything electrical to your vehicle, see
Servicing
Your Air Bag-Equipped Vehicle on page 1-55
.
Headlamps
The headlamp wiring is protected by four fuses.
An electrical overload will cause a lamp to go on and off.
If this happens, have your headlamp wiring checked
right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow or ice, the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
be sure to get it fixed.
Power Windows and Other Power
Options
Circuit breakers protect the power windows and other
power accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting the
circuit until the problem is fixed or goes away.
5-102
Fuses
Usage
1
Electrically-Controlled Air
Suspension
2
Passenger’s Side High-Beam
Headlamp
3
Passenger’s Side Low-Beam
Headlamp
4
Back-Up-Trailer Lamps
5
Driver’s Side High-Beam Headlamp
6
Driver’s Side Low-Beam Headlamp
7
Wash
8
Automatic Transfer Case
9
Windshield Wipers
10
Powertrain Control Module B
11
Fog Lamps
12
Stop Lamp
13
Cigarette Lighter
14
Ignition Coils
15
Blank
16
TBD-Ignition 1
17
Crank
Fuses
Usage
18
Air Bag
19
Electric Brake
20
Cooling Fan
21
Horn
22
Ignition E
23
Electronic Throttle Control
24
Instrument Panel Cluster,
Driver Information Center
25
Automatic Shift Lock Control System
26
Engine 1
27
Back-Up
28
Powertrain Control Module 1
29
Oxygen Sensor
30
Air Conditioning
31
Truck Body Controller
32
Trailer
33
Anti-Lock Brakes (ABS)
34
Ignition A
35
Blower Motor
5-105
Fuses
Usage
36
Ignition B
50
Passenger’s Side Trailer Turn
51
Driver’s Side Trailer Turn
52
Hazard Flashers
53
Electric Adjustable Pedal
54
A.I.R. Solenoid
56
A.I.R. Pump
Relays
Usage
37
Blank or Headlamp Wash
38
Rear Window Washer
39
Fog Lamps
40
Horn
Fuses
Usage
41
Fuel Pump
42
Windshield Wipers/Washer
43
High-Beam Headlamp
44
Air Conditioning
45
Cooling Fan
46
Headlamp Driver Module
47
Starter
49
Electric Adjustable Pedal
55
A.I.R. Solenoid
Miscellaneous
Usage
48
Instrument Panel Battery
49
Blank
5-106
Fuses
Usage
1
Electrically-Controlled Air
Suspension
2
Passenger’s Side High-Beam
Headlamp
3
Passenger’s Side Low-Beam
Headlamp
4
Back-Up-Trailer Lamps
5
Driver’s Side High-Beam Headlamp
6
Driver’s Side Low-Beam Headlamp
7
Wash
8
Automatic Transfer Case
9
Windshield Wipers
10
Powertrain Control Module B
11
Fog Lamps
12
Stop Lamp
13
Cigarette Lighter
14
Ignition Coils
15
Cannister Vent
16
TBD-Ignition 1
17
Crank
Fuses
Usage
18
Air Bag
19
Electric Brake
20
Cooling Fan
21
Horn
22
Ignition E
23
Electronic Throttle Control
24
Instrument Panel Cluster,
Driver Information Center
25
Automatic Shift Lock Control System
26
Engine 1
27
Back-Up
28
Powertrain Control Module 1
30
Air Conditioning
31
Truck Body Controller 1
32
Trailer
33
Anti-Lock Brakes (ABS)
34
Ignition A
35
Blower Motor
36
Ignition B
5-108
Fuses
Usage
50
Passenger’s Side Trailer Turn
51
Driver’s Side Trailer Turn
52
Hazard Flashers
53
Oxygen Sensor Bank A
54
Oxygen Sensor Bank B
55
Injector Bank A
56
Injector Bank B
57
Electric Adjustable Pedal
Relays
Usage
37
Headlamp Washer
38
Rear Window Washer
39
Fog Lamps
Fuses
Usage
40
Horn
41
Fuel Pump
42
Windshield Wipers/Washer
43
High-Beam Headlamp
44
Air Conditioning
45
Cooling Fan
46
Headlamp Driver Module
47
Starter
49
Electric Adjustable Pedal
58
Ignition 1
Miscellaneous
Usage
48
Instrument Panel Battery
5-109
Rear Underseat Fuse Block
5-110
Fuses
Usage
01
Right Door Control Module
02
Left Door Control Module
03
Endgate Module 2
04
Truck Body Controller 3
05
Rear Fog Lamps
06
Blank
07
Truck Body Controller 2
08
Power Seats
09
Rear Wiper
10
Driver Door Module
11
Amplifier
12
Passenger Door Module
13
Rear Climate Controls
14
Left Rear Parking Lamps
15
Blank
16
Vehicle Center High-Mounted
Stop Lamp
Fuses
Usage
17
Right Rear Parking Lamps
18
Locks
19
Liftgate Module/Driver Seat
Module
20
Sunroof
21
Lock
23
Blank
24
Unlock
25
Blank
26
Blank
27
OH Battery/OnStar
®
System
29
Rainsense™ Wipers
30
Parking Lamps
31
Truck Body Controller Accessory
32
Truck Body Controller 5
33
Front Wipers
34
Vehicle Stop
5-111
Fuses
Usage
35
Blank
36
Heat Ventilation Air Conditioning B
37
Front Parking Lamps
38
Left Turn Signal
39
Heat Ventilation Air Conditioning I
40
Truck Body Controller 4
41
Radio
42
Trailer Park
43
Right Turn Signal
Fuses
Usage
44
Heat Ventilation Air Conditioning
45
Rear Fog Lamps
46
Auxiliary Power 1
47
Ignition 0
48
Four-Wheel Drive
49
Blank
50
Truck Body Controller Ignition
51
Brakes
52
Truck Body Controller Run
5-112