Buick Park Avenue - 2004 Fuse Box Diagram

Buick Park Avenue - 2004 Fuse Box Diagram

These are some examples of vehicle symbols you may find on your vehicle:
v
PASS-Key
®
III Operation
Your vehicle is equipped
with the PASS-Key
®
III
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key
®
III is a passive
theft-deterrent system.
This means you don’t have
to do anything different
to arm or disarm the
system. It works when you
insert or remove the key
from the ignition.
When the PASS-Key
®
III system senses that someone
is using the wrong key, it shuts down the vehicle’s
starter and fuel systems. The starter will not work and
fuel will stop being delivered to the engine. Anyone
using a trial-and-error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
When trying to start the vehicle, if the engine does not
start and the SECURITY light comes on, the key may
have a damaged transponder. Turn the ignition off and
try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse. See
Fuses
and Circuit Breakers on page 5-99
. If the engine still
does not start with the other key, your vehicle needs
service. If your vehicle does start, the first key
may be faulty. See your dealer who can service the
PASS-Key
®
III to have a new key made.
It is possible for the PASS-Key
®
III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for programming additional keys only.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS-Key
®
III to
have new keys made. To program additional keys you
will need two current driver’s keys. You must add a
step to the following procedure. After Step 2, repeat
Steps 1 and 2 with the second current driver’s key.
Then continue with Step 3.
2-22
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
If your vehicle is equipped with the Head-Up Display
(HUD), an arrow will also appear in the display area
to indicate the direction of the turn or lane change.
See
Head-Up Display (HUD) on page 3-18
for more
information.
You may also have an arrow in the outside mirror that
flashes when the turn signal is used. See
Outside Power
Mirrors on page 2-39
for more information.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by itself
when you release it.
As you signal a turn or a lane change, if the arrows
flash at twice the normal rate, this may indicate that a
signal bulb may be burned out and other drivers will not
see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check the fuse and check for burned-out
bulbs. See
Fuses and Circuit Breakers on page 5-99
.
If you have a trailer towing option with added wiring for
the trailer lamps, the signal indicator will flash even if
a turn signal bulb is burned out. Check the front and
rear turn signal lamps regularly to make sure they
are working. You do not need to add a different flasher.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the
turn signal. To turn off the chime, move the turn signal
lever to the off position.
3-6
Care of the HUD
Clean the inside of the windshield as necessary to
remove any dirt or film that reduces the sharpness or
clarity of the HUD image.
To clean the HUD lens, spray household glass cleaner
on a soft, clean cloth. Gently wipe and dry the HUD
lens. Do not spray cleaner directly on the lens to avoid
cleaner leaking inside the unit.
If You Can’t See The HUD Image When
the Ignition is On
If the ignition is on and you can’t see the HUD image,
check to see if:
The headlamps are on.
Something is covering the HUD unit.
The HUD dimmer control is adjusted properly.
The HUD image is adjusted to the proper height.
A fuse is blown. See
Fuses and Circuit Breakers on
page 5-99
.
Keep in mind that your windshield is part of the HUD
system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD
or your HUD image may look blurred or out of focus.
Ultrasonic Rear Parking Assist
(URPA)
Your vehicle may be equipped with Ultrasonic Rear
Parking Assist (URPA). URPA is designed to help you
park while in REVERSE (R) and operates only at
speeds less than 3 mph (5 km/h). URPA can help you
avoid colliding with objects such as parked vehicles.
The system can detect objects 5 feet (1.5 m) behind
your vehicle and tell you how close those objects are to
your rear bumper.
The URPA display is located inside the vehicle, above
the rear window. It has three color-coded lights that can
be seen through the rearview mirror.
{
CAUTION:
Even with the Ultrasonic Rear Park Assist
system, the driver must check carefully before
backing up. The system does not operate above
typical backing speeds of 3 mph (5 km/h) while
CAUTION:
(Continued)
3-20
Certain electrical accessories may not be compatible to
the accessory power outlet and could result in blown
vehicle or adapter fuses. If you experience a problem
see your dealer for additional information on accessory
power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow
the proper installation instructions included with
the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Ashtrays and Cigarette Lighter
The front ashtray is located under the climate control
panel on the center console. Press on the door to
release the ashtray. To close, press on the door again.
To empty the ashtray, remove it from the center
console by gripping the edges and pulling straight out.
To reinstall, push the tray back into place.
The rear ashtrays are located on each rear door panel.
To remove a rear ashtray, open the lid and ease the
ashtray upward until the edge can be grasped to pull the
ashtray up and out.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
There is a cigarette lighter near the front ashtray.
To use it, push it in all the way and let go. When it’s
ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
3-23
A. Battery. See
Battery on page 5-43
.
B. Underhood Fuse Block. See “Underhood Fuse
Block” under
Fuses and Circuit Breakers on
page 5-99
.
C. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-27
.
D. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-14
.
E. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-14
.
F. Engine Coolant Air Bleed Valve. See “How to Add
Coolant to the Radiator” under
Cooling System
on page 5-30
.
G. Automatic Transaxle Fluid Dipstick. See “Checking
the Fluid Level” under
Automatic Transaxle Fluid
on page 5-23
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-40
.
I. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-39
.
J. Engine Coolant Recovery Tank. See
Cooling System
on page 5-30
.
K. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-20
.
5-13
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of damage
caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
There are four fuse blocks in your vehicle: the main and
auxiliary instrument panel fuse blocks, the underhood
fuse block and the rear fuse block.
Main and Auxiliary Instrument Panel
Fuse Blocks
The main and auxiliary instrument panel fuse blocks are
located under the instrument panel, on the passenger’s
side of the vehicle. Lamps, connectors and the
HVAC duct temperature sensors may need to be
disconnected and removed to allow access to these
fuse blocks.
Remove the hush panel on the passenger’s side to
reveal the fuses by performing the following steps:
1. Remove the two screws located along the front
edge of the panel.
2. Lower the hush panel.
3. Remove the fuse block cover.
4. Place the wide end of the fuse puller over the
plastic end of the fuse.
5. Squeeze the ends over the fuse and pull it out.
When finished, reinstall the fuse block cover and
the hush panel. Reinstall lamps, connectors and HVAC
duct temperature sensors if they were removed.
5-99
Main Instrument Panel Fuse Block
Fuses
Usage
SBM
Interior Lamps
PDM
PDM Module
A/C
HVAC Motor, HVAC Mix Motors
Fuses
Usage
IGN SEN
Auto Dimming Mirror, Driver HTS
Seat, Rear Defog Relay, MEM
Module, Cool LVL Sensor,
Pass Heated Seat
ELC
HVAC Flat Pk Mtrs, Electronic Level
Control Sensor, Electronic Level
Control Sensor (R Bec)
ABS
Anti-Lock Brake System Module
HVAC
HVAC Main Con Head, HVAC
Programmer, Instrument Panel
Cluster
CR CONT
Stepper Motor Cruise, Cruise Switch
HUD
Head-Up Display Switch, Head-Up
Display
CSTR/SBM
HVAC Programmer, Instrument
Panel Cluster, SBM (275 to LCM)
(1135 to BTSI SL)
LP PK L
Underhood Lamp, Left Park/
Sidemarker, Left Park/Turn Lamp,
SBM, Left Tail Signal Lamp, Left
Tail/Stoplamp, Left Rear Sidemarker
5-100
Fuses
Usage
LP PK R
Right Park/Sidemarker Lamp, Right
ParK/Turn Lamp, Right Tail/Sign
Lamp, Right Tail/Stoplamp, Right
Rear Sidemarker, Stop/Taillamp,
Tail/Signal Lamp, License Lamp, RFA
RUN
Run/Accessory
WSW
Wiper Motor
Blank
Not Used
WSW/RFA
Wiper Switch, RFA, Rain Sense
B/U LP
Auto Dimming Mirror,
Back-Up Lamps
Auxiliary Instrument Panel Fuse Block
Fuses
Usage
PERIM LP
Perimeter Lamps
ACCY
Accessory
IGN 3
Ignition 3
5-101
Fuses
Usage
10
Spare
11
Spare
12
Injectors #1-6
13
C-31
14
Right High Beam
15
Spare
16
Left High Beam
17
Spare
18
Right Low Beam
19
Left Low Beam
20
Stop
21
Fuel Pump Relay (Wire in BEC)
22
Run/Crank
23
Powertrain Control Module
24
Parking Lamps
25
Hazard Flashers
26
Spare
27
Spare
28
ABS #2
Relays
Usage
29
Ignition
30
Horn
31
Cooling Fan 1
32
Starter
33
Not Used
34
Cooling Fan SP
35
Cooling Fan 2
36
Air Conditioning Clutch
37
Fuel Pump
Fuses
Usage
38
Bat #1
39
Blower Motor
40
Cooling Fan 1
41
Headlamp
42
BAT #2
43
Ignition
44
Starter
45
ABS
46
Fuse Puller
5-103
Removing the Rear Seat Cushion
Notice:
If, when removing or reinstalling the rear
seat, you do not do it carefully, you could damage the
fuse center. Avoid contact between the rear seat and
the fuse center whenever you remove or reinstall the
rear seat.
To remove the rear seat cushion, do the following:
1. Pull up on the front of the cushion to release the
front hooks.
2. Pull the cushion up and out toward the front of
the vehicle.
To reinstall the rear seat cushion, do the following:
{
CAUTION:
A safety belt that isn’t properly routed through
the seat cushion or is twisted won’t provide the
protection needed in a crash. If the safety belt
hasn’t been routed through the seat cushion
at all, it won’t be there to work for the next
passenger. The person sitting in that position
could be badly injured. After reinstalling the
seat cushion, always check to be sure that the
safety belts are properly routed and are not
twisted.
5-104
Rear Compartment Fuse Block
Additional fuses are located in the fuse center under the
rear seat.
Relays
Usage
1
Heated Backlite
2
Retained Accessory Power (RAP)
3
Trunk Release
4
Electronic Level Control
Circuit
Breakers
Usage
5
Power Seat
6
Electronic Level Control Sensor,
Electronic Level Control Compressor
Solenoid
Fuses
Usage
7
Crank
8
Accessory Outlet
9
Powertrain Control Module for
Cruise
10
SBM Module
11
Radio/Phone
12
Sunroof
13
Spare
14
CD Changer, Phone
15
Driver Door Module
16
Spare
5-106
Fuses
Usage
17
Radio
18
Driver Heated Seat Module
19
Rear Door Module
20
Trunk Release
21
Spare
22
Instrument Panel Ashtray Cigarette
Lighter
Fuses
Usage
23
Spare
24
Spare
25
Passenger Heated Seat Module
26
Right Rear Cig Lighter
27
Left Rear Cig Lighter
28
RFA, Memory Seat Module,
Driver Seat Switch
5-107