Cadillac Seville - 2003 Fuse Box Diagram

Cadillac Seville - 2003 Fuse Box Diagram

Testing
the
A!arm
1.
2.
3.
From inside the
uehieie, roii down the window, then
get
out
of
the
vehicle, keeping the
door open.
From
outside of the vehicle, with the door
open,
lock
the vehicle using the power
door lock or the
remote
keyless
entry transmitter and close the door.
Wait
30
seconds until the SECURITY
lamp
goes
off.
Reach in and
unlock the door using the
manual
lock
and
open
the
door.
The horn will sound
and
the hazard lights will flash.
You
can turn
off
the
alarm by unlocking the driver's door
with
your
key, using the unlock button on
the
remote
keyless
entry
transmitter
or
by starting the car with
a
valid
key.
If
the alarm does
not
sound
when it should,
check
to
see
if
the horn works.
The horn fuse may
be blown.
To
replace
the
fuse,
see
Fuses and Circuit Breakers on
p y e
5-93.
ii
iire
iuse
does
noi
need
io
be repiacea, you
may
need
to
have
your vehicle serviced.
To
reduce
the possibility
of
theft, always
arm the
theft-deterrent
system
when leaving your vehicle.
The valet lockout switch is
located inside the
glove box.
Press the switch to
ON
to disable the
use
of
the trunk,
fuel door, garage
door
opener and cellular telephone
(option). The
remote keyless entry transmitter cannot
open the trunk
if
the valet lockout switch is
in
ON.
Press this switch to
OFF
to enable the use of the trunk,
fuel door, garage
door
opener
and optional cellular
telephone.
Locking the glove
box with your key will also help to
secure your vehicle.
2-1
9
If
the
engine
does
not
sta.rt,
a.nd
the
key
appears
to
be
undamaged,
try
another ignition key. At this time,
you
may ais0 want to check
the fuse. See
Fuses
and
Circuit
Breakers
on
page
5-93.
If
the engine still
does
not start with the other key, your vehicle needs
service.
If
your vehicle does
start, the first key may
be
faulty.
See
your
dealer
who
can service the
to have a new
key
made.
It is possible
for
the [email protected] decoder to learn the
transponder value of a
new
or
replacement key. Up to
10
additional keys may
be
programmed
for
the vehicle. This
procedure is for learning additional keys only.
Canadian
Owners:
If
you
lose or
damage your keys,
only
a
GM
dealer can service [email protected]
to have
new
keys
made.
To
program additional keys you will
require
two current driver's keys (black in color). You
must
add a step to the following procedure. After
Step
2,
repeat
Steps
1
and 2 with
the
second current driver's
key.
Then continue with
Step
3.
To
program
the
new
key
do the following:
1.
Verify that the new
key
has
PK3
stamped
on it.
3.
Affer
the
engine
has
sfaded,
turn
the key to
OFF,
and
remove the key.
4.
Insert the key to be
programmed and turn
it
to
ON
within
10
seconds of removing the previous key.
5.
The
SECURITY light will turn
off
once the key has
been
programmed.
it
may
not
be apparent
that
the
SECURITY light went
on
due to how quickly the
key is programmed.
6. Repeat the Steps
1
through
4
if
additional keys are
to be
programmed.
If
you are ever driving and the SECURITY light comes
on
and stays on, you will be able to restart your
engine
if
you turn it
off.
Your
PASS- [email protected] system,
however, is not working properly and
must
be serviced
by your dealer. Your vehicle is not protected by the
system
at
this time.
If
you lose or
damage
a
Ill
key, your dealer
to have
a
new
key
made.
In an
emergency, contact Cadillac Roadside Assistance.
Can
Rnqr(r;dn
Cnnfinn
nn
n-nn
7
E
vvv
'
l"UU"'UU
V
V
I
"#VU
",,
puyv
,
e.
2. Insert the current driver's key in the ignition
and
start
the engine. If the engine will not start see
your
dealer
for
service.
2-2
1
Push the control forward and the steering wheel
moves
toward the front of the vehicle. Push the control
rearward and
the steering wheel
moves toward the rear
of the vehicle.
To set the memory position,
see
DIC
Vehicle
Personalization on
page 3-60 and
Memory
Seat,
Mirrors and Steering Wheel on page 2-49.
Turn SignaVMultifunction
Lever
Turn and
Lane-Change
Signals
To signal a turn, move the lever on the left
side of the
steering wheel all the way
up
or
down.
The
lever
returns
automatically when
the turn is complete.
h
l
i
The lever located on the left side of the steering column
includes the following:
Turn and Lane Change
Signals
Headlamp High/Low-Beam Changer
Flash-To-Pass
For information on the exterior lamps,
see
Exterior
Lamps on page
3-15.
t
An arrow located on the
instrument panel
cluster
will flash in the
direction
of
the turn or lane
change.
Raise or lower the lever until the arrow starts to flash
to
signal a lane change. Hold it there until the
lane
change is complete. The
lever returns when
it
is
released.
If
the turn signal is left on, a warning chime
will
sound
and the Driver Information Center (DIC)
will
display
TURN SIGNAL
ON
after driving about
a
mile to remind
you to turn it
off.
Arrows that flash rapidly
when signaling for a turn or
lane change
may
be
caused by a burned-out signal
bulb.
Other drivers won’t
see
the turn signal.
Replace burned-out bulbs to help avoid possible
accidents. Check
the
fuse
and
for
burned-out
bulbs
if
the arrow fails to work
when signaling
a
turn.
See
Fuses
and Circuit
Breakers
on page 5-93.
3-8
If
the
URPA
system
is
not
f~Inctioning
prsper!y,
the
display
will
flash
red,
indicating
that there is a
problem.
The
iight
will
also
flash
red
while driving
if
a trailer is
attached
to
your
vehicle,
or
a bicycle or object is on the
back
of,
or
hanging
out of your trunk. The light will
continue to flash until the
trailer
or the object is removed
and
your
vehicle is driven
forward
at least
15
mph
(25
km/h).
It may also
flash red
if
the
ultrasonic
sensors are not
kept
clean.
So
be sure
to
keep
your
rear bumper free of
mud,
dirt,
snow,
ice
and slush or
materials such as
paint
or
the
system
may
not
work
properly.
If
after
cleaning the rear
bumper and driving forward at least
15
mph
(25
km/h), the display continues to flash red, see
your
dealer.
For
cleaning
instructions,
see
Cleaning
the
Outside
of
Your
Vehicle
on
page
5-86.
It
may
also
flash red
if
your vehicle is moving
in
REVERSE
(R)
at
a
speed
greater
than
3
mph
(5
km/h).
Other
conditions
that
may
affect
system performance
include
things like the vibrations
from
a jackhammer or
the
compression of air
brakes on a
very large truck.
As always,
drivers
should
use care when backing up
a
vehicle.
Always
look
behind
you, being sure to check
for
other
vehicles,
obstructions and blind spots.
nbwzaaum
y
r
u v v c l
wuJet§
A
nnneenm.
C)nmn.nu
AI
m+
Your
vehicle is equipped with accessory
power
outlets.
The outlets can be used to plug in electrical equipment
such as
a cellular telephone,
CB
radio,
etc.
The accessory power outlets are located at the rear
of
the center console and on the lower inboard carpeted
panel on the passenger’s side of the
vehicle.
Your vehicle may have a small cap
that
must be
removed
to
access the accessory power outlet. If it
does,
when
not using the outlet be sure to cover it with
the protective cap.
The accessory power outlet will
only operate when the
ignition is in ACC
or
ON
and for
10
minutes after
turning the ignition
OFF.
If
you would like the accessory
power outlet to operate regardless of ignition position,
and for extended periods of time,
see
your dealer
for more information.
Notice:
When using an accessory power outlet,
maximum electrical
load
must
not exceed amperage
rating.
Always turn
off
any electrical equipment
when
not
in
use. Leaving electrical equipment on for
extended periods will drain
your
battery.
Certain accessory power plugs may not be compatible
to the accessory power outlet and could result
in
problem see
your dealer for additional information on
the
accessory
power plugs.
b1Wa.n
v v I
I
\
~ehicle
OF
adaptzr
fuses.
If
YOU
expe;ien~e
2
3-23
A. Windshield Washer
Fluid Reservoir
B.
Underhood Fuse Block
C. Power
Steering Fluid Reservoir
D.
Engine
Oil
Fill Location
E. Engine Oil Dipstick
F.
Brake
Master
Cylinder Reservoir
G.
Transaxle Fluid Cap and Dipstick
H. Engine Air Cleaner/Filter
I.
Engine
Coolant
Surge
Tank and Pressure Cap
If
the CHECK OIL LEVEL
message
appears
on
the
instrument cluster, it means
you
need to check
your engine oil level right away.
For
more information,
see
“CHECK
OIL
LEVEL”
under
DIC
Warnings
and
Messages on page
3-52.
YOU should check your engine oil level regularly; this
is
an
added reminder.
5-1
5
Power
Steering
Fluid
I
I
The power steering fluid reservoir is located next to the
underhood
fuse block on the passenger’s side of the
vehicle.
See
Engine
Compartment
Overview
on
page
5-14
for
more information on location.
When to Check
Power Steering Fluid
It is not necessary to regularly check
power steering fluid
unless you
suspect there is a leak in the system
or
you hear
an unusual noise.
A fluid
loss
in
this system
could indicate a problem. Have the system inspected
and repaired.
How
to
Check Power
Steering
Fluid
Turn the key
off,
let the
engine
compartment cool down,
wipe the cap
and the top of the reservoir
clean, then
unscrew the cap
and
wipe
the
dipstick
with a clean rag.
Replace the cap and completely tighten it.
Then
remove the cap again and look at
the
fluid level on
the
dipstick.
The level should be at
the
FULL
COLD
mark.
If
necessary, add only enough fluid to bring the level up
to
the mark.
What
to
Use
To determine what kind of fluid to
use,
see
Part
D:
Recommended Fluids and
Lubricants
on
page
6-
15.
Always
use
the proper fluid. Failure to use
the
proper
fluid can
cause leaks and
damage
hoses
and
seals.
Windshield
Washer
Fluid
What
to
Use
When
you
need windshield washer
fluid,
be sure to read
the manufacturer’s instructions before use.
If
you
will
be operating your vehicle in an area where
the
temperature may fall below
freezing,
use a fluid that
has
sufficient protection
against
freezing.
See
Engine
Compartment
Overview
on
page
5-14
for
reservoir
location.
5-38
Adding
Washer
Fhij
When your
vekic!e’s windshield
washer
fluid
level
becomes
low,
a
CHECK
WASHER
FLUID
message will
appear
on
the
Driver Information Center (DIC).
You
will
need to add fluid soon.
The windshield washer
fluid reservoir
is
located
next to the
underhood fuse
block on
the passenger’s
side of the vehicle.
Open
the
cap
with
the
washer
symbol
on it. Add
washer
fluid
until
the
tank
is full.
*
hen
usin
her
fluid, follow
the
~
a
n
~
~
~
~
~
in
aims for adding
water.
Don’t
mix
wat
-ts-use
washer
fluid.
Waier
can
ca
n
to
freeze and
k
and other
parts
clean as
~
5-39
The
remote positive
(+)
terminal is located in the
engine compartment
on
the
passenger’s side of the
vehicle.-A
secondrem
positive
(+)
terminal
is
located
on
the rear
underseat fuse block.
the red plastic cap to
access
the
terminal.
lote
Lift
The
remote negative
(-)
terminal is located near the
power steering fluid reservoir. It is marked
“GND
(-).”
See
Engine
Compartment
Overview
on
page
5-14
for
more
information on location.
You will not
see the battery
of
your vehicle under the
hood. It
is
located under the rear passenger’s seat. You
will not need to access
the battery for
jump starting.
The
remote positive
(+)
terminal is for that purpose.
I
I
An
electric
fan
can
start up even
when the
engine
is
not
running
and
can
injure
you. Keep
hands,
clothing
and
tools away from any
underhood
electric fan.
I
Using a match
near a bat1
-
an cause battery
gas
to
explode.
People
have
been
hurt
doing
this,
and
some have
been blinded. Use a
flashlight
if
you need more
light.
Be
sure
the
battery
has
enough water. You
don’t
need
to
add water to
battery
installed
in
your new
vehicle.
But
if
a
battery
has
filler caps,
be sure
the
right
amount
of
fluid
is
there.
If
it
is
low,
add
water
to take
care
of
that
first.
If
you
don’t,
explosive
gas
could
be
present.
CAUTION: (Continued)
5-46
Electrical
System
Add-on
Electrical
Equipment
Nofice:
Don’t add anything electrical to your
vehicle unless you check with
your
dealer first.
Some electrical equipment
can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some
add-on electrical equipment can
keep other components from working as they
should.
Your vehicle has
an air bag
system. Before attempting
to add anything electrical to your vehicle, see
Servicing Your
Air Bag-Equipped Vehicle
on
page
1-5
5 .
Headlamp
Wiring
The headlamp wiring has
an individual fuse.
An
electrical overload will cause the lamps to go
on and
off,
or in some
cases to remain
off.
If this happens,
have
the headlamp wiring checked right away.
Windshield
Wiper
Fuses
The windshield wiper motor
is protected by
an
internal
circuit breaker.
If
the wiper
motor
overheats
due
to
heavy
snow, the wipers will stop until the motor
cools
and will then restart.
A
fuse
powers the wiper
motor.
If
the fuse
blows,
there
is an electrical problem. Be
sure to have it fixed.
Power
Windows
and
Other
Power
Options
Circuit breakers protect the power
windows
and
power
seats.
When the current load is too heavy,
the
circuit
breaker opens and closes, protecting the
circuit
until
the
problem is fixed or
goes
away.
5-92
The
wiring
circuits in your vehicie are protected from
short circuits by
a combination of fuses and circuit
breakers. This greatly
reduces the chance of fires
caused by electrical problems.
Look
at
the silver-colored band inside the fuse.
If
the
band is broken or melted, replace the fuse.
Be sure you
replace
a
bad
fuse
with
a
new
one of the identical
size
and
rating.
If
a
fuse should blow,
see your dealer
for service immediately.
If
you
ever
have
a
problem
on the road and
don’t
have
a
spare
fuse,
you
can “borrow” one that has the
same
amperage.
Pick
some feature of your vehicle that
you
can
get along without
-
like the radio or cigarette
lighter
-
and
use its fuse,
if
it is the correct amperage.
Replace it as soon
as
you
can.
The fuses are located in two fuse blocks, one located
near
the engine compartment
on
the passenger’s
side
and
the
other
under
the rear seat on the driver’s
side.
If
a
fuse should blow,
have
vour vehicle serviced
by your dealer immediately.
The underhood fuse block is located in the front of the
engine compartment
between
the windshield washer
fluid reservoir and the power steering fluid reservoir on
the passenger’s side
of
the vehicle. See
Engine
Compartment Overview
on
page
5-14
for more
information on location.
To access the fuses, push in the two tabs located at
each
end of the fuse block cover. Then, lift the cover
off.
5-93
Fuses
ALDL
1
Usage
2
Windshield
Wipers
3
Accessory
4
Headlamp Low
Beam
Left
5
Not Used
6
Instrument Panel
7
Headlamp Low
Beam
Right
8
Headlamls Hiah Beam
Left
10
Headlamp High Beam
Right
9
Powertrain Control Module Battery
I
I
5-94
3.
With the seat cushion lowered, push rearward and
then press down
on the seat cushion until the
4.
Check to make
sure the safety belts are properly
routed and
that
no portion of any safety belt is
trapped under
the
seat.
Also
make sure the seat
cushion is secured.
spring
!ocks
CT:
bGth
ends
engage.
Rear
Underseat
Fuse
Block
To access the fuses, push
in the two tabs located at
each
end of the fuse block cover. Then, lift the cover
off.
1
Fuel Pump
2
3
Heater, Ventilation, Air Conditioner
Memory Seat, Tilt
and Telescoping
Steering
t)l-..,-.-
U l U V V G l
This
fuse block
is
located under the rear seat
on the
driver’s
side of the vehicle. The rear seat cushion must
he
remwed
tc!
access
the
fuse
b!ock.
See
,9e,rmvh
Y
the
Rear Seat
Cushion
listed previously in this section.
5-97
Relays
Usage
51
Interior Lamps
The
spare fuses and fuse puller
are located in the
underhood fuse
block.
See
Underhood Fuse
Block
listed
previously
for more information.
5-99