Cadillac Seville - 2002 Fuse Box Diagram

Cadillac Seville - 2002 Fuse Box Diagram

2-19
Testing the Alarm
1.
From inside the vehicle, roll down the window,
then get out of the vehicle, keeping the door open.
2.
From outside of the vehicle, with the door open,
lock the vehicle using the power door lock or the
remote keyless entry system and close the door.
Wait 30 seconds until the SECURITY lamp goes off.
3.
Reach in and unlock the door using the manual
lock and open the door. The horn will sound and
the hazard lights will flash.
You can turn off the alarm by unlocking the driver’s
door with your key, using the unlock button on the
remote keyless entry transmitter or by starting the
car with a valid key.
If the alarm does not sound when it should, check to
see if the horn works. The horn fuse may be blown.
To replace the fuse, see “Fuses and Circuit Breakers”
in the Index. If the fuse does not need to be replaced,
you may need to have your vehicle serviced.
To reduce the possibility of theft, always arm the
theft
-
deterrent system when leaving your vehicle.
Valet Lockout Switch
The valet lockout switch
is located inside the
glove box.
Press the switch to ON to disable the use of the trunk,
fuel door, garage door opener and cellular telephone
(option). The remote keyless entry transmitter cannot
open the trunk or the fuel door if the valet lockout
switch is in ON.
Press this switch to OFF to enable the use of the
trunk, fuel door, garage door opener and cellular
telephone (option).
Locking the glove box with your key will also help
to secure your vehicle.
2-21
If the engine does not start, and the key appears to be
undamaged, try another ignition key. At this time, you
may also want to check the fuse. See “Fuses and Circuit
Breakers” in the Index. If the engine still does not start
with the other key, your vehicle needs service. If your
vehicle does start, the first key may be faulty. See your
dealer who can service the PASS
-
Key III to have a
new key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS
-
Key III to have new
keys made. To program additional keys you will require
two current driver’s keys (black in color). You must add
a step to the following procedure. After Step 2, repeat
Steps 1 and 2 with the second current driver’s key.
Then continue with Step 3.
To program the new key do the following:
1.
Verify that the new key has PK3 stamped on it.
2.
Insert the current driver’s key in the ignition and
start the engine. If the engine will not start see your
dealer for service.
3.
After the engine has started, turn the key to OFF,
and remove the key.
4.
Insert the key to be programmed and turn it to ON
within ten seconds of removing the previous key.
5.
The SECURITY light will turn off once the key has
been programmed. It may not be apparent that the
SECURITY light went on due to how quickly the
key is programmed.
6.
Repeat the Steps 1 through 4 if additional keys are
to be programmed.
If you are ever driving and the SECURITY light comes
on and stays on, you will be able to restart your engine
if you turn it off. Your PASS
-
Key III system,
however, is not working properly and must be serviced
by your dealer. Your vehicle is not protected by the
PASS
-
Key III system at this time.
If you lose or damage a PASS
-
Key III key, see your
dealer to have a new key made.
In an emergency, contact Cadillac Roadside Assistance.
See “Roadside Assistance” in the Index.
2-39
Turn Signal/Multifunction Lever
The lever located on the left side of the steering column
includes the following:
D
Turn and Lane Change Signals
D
Headlamp High/Low
-
Beam Changer
D
Flash
-
To
-
Pass Feature
For information on the exterior lamps, see “Exterior
Lamps” later in this section.
Turn and Lane-Change Signals
To signal a turn, move the lever on the left side of the
steering wheel all the way up or down. The lever returns
automatically when the turn is complete.
An arrow located on the
instrument panel cluster
will flash in the direction
of the turn or lane change.
Raise or lower the lever until the arrow starts to flash to
signal a lane change. Hold it there until the lane change
is complete. The lever returns when it is released.
If the turn signal is left on, a warning chime will sound
and the Driver Information Center (DIC) will display
TURN SIGNAL ON after driving about a mile to
remind you to turn it off.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned
-
out signal bulb.
Other drivers won’t see the turn signal.
Replace burned
-
out bulbs to help avoid possible
accidents. Check the fuse (see “Fuses and Circuit
Breakers” in the Index) and for burned
-
out bulbs
if the arrow fails to work when signaling a turn.
2-60
Accessory Power Outlets
Your vehicle is equipped with accessory power outlets.
The outlets can be used to plug in electrical equipment
such as a cellular telephone, CB radio, etc.
The accessory power outlets are located at the rear of the
center console and on the lower inboard carpeted panel
on the passenger’s side of the vehicle.
Your vehicle may have a small cap that must be removed
to access the accessory power outlet. If it does, when
not using the outlet be sure to cover it with the
protective cap.
The accessory power outlet will only operate when the
ignition is in ACC or ON and for 10 minutes after
turning the ignition OFF. If you would like the accessory
power outlet to operate regardless of ignition position,
and for extended periods of time, see your dealer for
more information.
NOTICE:
When using accessory power outlets:
D
Maximum load of any electrical equipment
should not exceed the maximum amperage
for the outlet.
D
Be sure to turn off any electrical equipment
when not in use. Leaving electrical
equipment on for extended periods can
drain the battery.
Certain accessory power plugs may not be compatible
to the accessory power outlet and could result in blown
vehicle or adapter fuses. If you experience a problem see
your dealer for additional information on the accessory
power plugs.
2-61
NOTICE:
Adding some electrical equipment to your vehicle
can damage it or keep other things from working
as they should. This wouldn’t be covered by your
warranty. Check with your dealer before adding
electrical equipment, and never use anything that
exceeds the fuse rating.
Follow the proper installation instructions that are
included with any electrical equipment you install.
NOTICE:
Power outlets are designed for accessory plugs
only. Do not hang any type of accessory or
accessory bracket from the plug. Improper use
of the accessory power outlets can cause damage
not covered by your warranty.
Cellular Telephone (Option)
With this option, your vehicle has been prewired
for dealer installation of a portable cellular telephone
system. The system has steering wheel telephone
controls and information output through the Driver
Information Center (DIC). Voice activation with remote
record and hands
-
free operation are standard features.
For more information, contact your dealer. A user’s
guide is provided with the telephone.
5-5
The remote
positive (+) terminal is
located in the engine
compartment on the
passenger’s side of the
vehicle. A second
remote positive (+)
terminal is located on
the rear underseat fuse
block. Lift the red
plastic cap to access
the terminal.
The remote negative (
-
) terminal is located near the
power steering fluid reservoir. It is marked
“GND (
-
).” See “Engine Compartment Overview” in
the Index for more information on location.
You will not see the battery of your vehicle under the
hood. It is located under the rear passenger’s seat.
You will not need to access the battery for jump
starting. The remote positive (+) terminal is for
that purpose.
CAUTION:
An electric fan can start up even when the engine
is not running and can injure you. Keep hands,
clothing and tools away from any underhood
electric fan.
6-11
Engine Compartment Overview
When you open the hood, you’ll see:
A.
Windshield Washer Fluid Reservoir
B.
Underhood Fuse Block
C.
Power Steering Fluid Reservoir
D.
Engine Oil Fill Location
E.
Engine Oil Dipstick
F.
Brake Master Cylinder Reservoir
G.
Transaxle Fluid Cap and Dipstick
H.
Engine Air Cleaner/Filter
I.
Engine Coolant Surge Tank and
Pressure Cap
6-28
Power Steering Fluid
The power steering fluid
reservoir is located next
to the underhood fuse block
on the passenger’s side of
the vehicle.
When to Check Power Steering Fluid
It is not necessary to regularly check power steering
fluid unless you suspect there is a leak in the system or
you hear an unusual noise. A fluid loss in this system
could indicate a problem. Have the system inspected and
repaired. See “Engine Compartment Overview” in the
Index for reservoir location.
How to Check Power Steering Fluid
Turn the key off, let the engine compartment cool down,
wipe the cap and the top of the reservoir clean, then
unscrew the cap and wipe the dipstick with a clean rag.
Replace the cap and completely tighten it. Then remove
the cap again and look at the fluid level on the dipstick.
The level should be at the FULL COLD mark.
If necessary, add only enough fluid to bring the
level up to the mark.
What to Use
To determine what kind of fluid to use, see
“Recommended Fluids and Lubricants” in the Index.
Always use the proper fluid. Failure to use the proper
fluid can cause leaks and damage hoses and seals.
6-29
Windshield Washer Fluid
What to Use
When you need windshield washer fluid, be sure to read
the manufacturer’s instructions before use. If you will be
operating your vehicle in an area where the temperature
may fall below freezing, use a fluid that has sufficient
protection against freezing. See “Engine Compartment
Overview” in the Index for reservoir location.
Adding Washer Fluid
When your vehicle’s windshield washer fluid level
becomes low, a CHECK WASHER FLUID message will
appear on the Driver Information Center (DIC). You will
need to add fluid soon.
The windshield washer
fluid reservoir is located
next to the underhood fuse
block on the passenger’s
side of the vehicle.
Open the cap with the washer symbol on it.
Add washer fluid until the tank is full.
NOTICE:
D
When using concentrated washer fluid,
follow the manufacturer’s instructions for
adding water.
D
Don’t mix water with ready
-
to
-
use washer
fluid. Water can cause the solution to freeze
and damage your washer fluid tank and
other parts of the washer system. Also,
water doesn’t clean as well as washer fluid.
D
Fill your washer fluid tank only
three
-
quarters full when it’s very cold.
This allows for expansion if freezing
occurs, which could damage the tank if
it is completely full.
D
Don’t use engine coolant (antifreeze) in
your windshield washer. It can damage
your washer system and paint.
6-70
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring has an individual fuse. An
electrical overload will cause the lamps to go on and off,
or in some cases to remain off. If this happens, have the
headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker. If the wiper motor overheats due to
heavy snow, the wipers will stop until the motor cools
and will then restart.
A MiniFuse
R
powers the wiper motor. If the MiniFuse
blows, there is an electrical problem. Be sure to have
it fixed.
Power Windows and Other Power Options
Circuit breakers protect the power windows. When the
current load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed or
goes away.
6-71
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of fires caused
by electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating. If a MaxiFuse should blow, see your dealer
for service immediately.
If you ever have a problem on the road and don’t have a
spare fuse, you can “borrow” one that has the same
amperage. Pick some feature of your vehicle that you
can get along without
--
like the radio or cigarette
lighter
--
and use its fuse, if it is the correct amperage.
Replace it as soon as you can.
The MaxiFuses are located in two fuse blocks, one
located near the engine compartment on the passenger’s
side and the other under the rear seat on the driver’s
side. If a MaxiFuse should blow, have your vehicle
serviced by your dealer immediately.
Underhood Fuse Block
The underhood fuse block is located in the front of the
engine compartment between the windshield washer
fluid reservoir and the power steering fluid reservoir on
the passenger’s side of the vehicle. See “Engine
Compartment Overview” in the Index for more
information on location.
To access the fuses, push in the two tabs located at each
end of the fuse block cover. Then, lift the cover off.
6-72
Minifuses
Usage
1
ALDL
2
Accessory
3
Windshield Wipers
4
Not Used
5
Headlamp Low Beam Left
Minifuses
Usage
6
Headlamp Low Beam Right
7
Instrument Panel
8
Powertrain Control
Module Battery
9
Headlamp High Beam Right
10
Headlamp High Beam Left
11
Ignition 1
12
Fog Lamps
13
Transmission
14
Cruise Control
15
Coil MDL
16
Injector Bank #2
17
Not Used
18
Not Used
19
Powertrain Control
Module Ignition
20
Oxygen Sensor
6-73
Minifuses
Usage
21
Injector Bank #1
22
Auxiliary Power, (Cltr2)
23
Cigar Lighter
24
Daytime Running Lamps
25
Horn
26
Air Conditioner Clutch
Micro Relays
Usage
27
Headlamp High Beam
28
Headlamp Low Beam
29
Fog Lamps
30
Daytime Running Lamps
31
Horn
32
Air Conditioner Clutch
Mini Relays
Usage
33
Not Used
34
Accessory
Mini Relays
Usage
35
Not Used
36
Starter 1
37
Cooling Fan Secondary
38
Ignition 1
39
Cooling Fan Series/Parallel
40
Cooling Fan Primary
Maxibreaker
Usage
41
Starter
42
Export Use
MaxiFuses
Usage
43
Not Used
44
Antilock Brake System
45
Air Pump
46
Cooling Fan Secondary
47
Cooling Fan Primary
The spare fuses are located in numbers 48 through 52.
The fuse puller is located in number 53.
6-74
Removing the Rear Seat Cushion
NOTICE:
The battery and main fuse blocks are located
under the rear seat cushion. The battery’s ground
terminal and some relay wires are exposed.
To help avoid damage to the battery and wires,
be careful when removing or reinstalling the
seat cushion. Do not remove covers from covered
parts. Do not store anything under the seat, as
objects could touch exposed wires and cause
a short.
To remove the rear seat cushion, do the following;
1.
Pull up on the front of the cushion to release the
front hooks.
2.
Pull the cushion up and out toward the front of
the vehicle.
To reinstall the rear seat cushion, do the following:
6-75
CAUTION:
A safety belt that isn’t properly routed through
the seat cushion or is twisted won’t provide the
protection needed in a crash. If the safety belt
hasn’t been routed through the seat cushion at
all, it won’t be there to work for the next
passenger. The person sitting in that position
could be badly injured. After reinstalling the seat
cushion, always check to be sure that the safety
belts are properly routed and are not twisted.
1.
Buckle the center passenger position safety belt, then
route the safety belts through the proper slots in the
seat cushion. Don’t let the safety belts get twisted.
2.
Slide the rear of the cushion up and under the
seatback so the rear
-
locating guides hook into the
wire loops on the back frame.
3.
With the seat cushion lowered, push rearward and
then press down on the seat cushion until the spring
locks on both ends engage.
4.
Check to make sure the safety belts are properly
routed and that no portion of any safety belt is
trapped under the seat. Also make sure the seat
cushion is secured.
Rear Underseat Fuse Block
This fuse block is located under the rear seat on the
driver’s side of the vehicle. The rear seat cushion must
be removed to access the fuse block. See “Removing the
Rear Seat Cushion” listed previously in this section.
To access the fuses, push in the two tabs located at each
end of the fuse block cover. Then, lift the cover off.
6-76
Minifuses
Usage
1
Fuel Pump
2
Heater, Ventilation, Air
Conditioner Blower
3
Memory Seat, Tilt and
Telescoping Steering
4
SDAR (XM
t
Satellite
Radio
-
If Equipped)
5
Driver Door Module
6
Heated Seat Left Rear
7
Power Tilt and
Telescoping Steering
8
Supplemental Inflation Restraint
9
Not Used
10
Lamps Park Right
11
Fuel Tank Ventilation Solenoid
12
Ignition 1
13
Lamps, Parking Left
6-77
Minifuses
Usage
14
Interior Lamp Dimmer Module
15
Navigation
16
Heated Seat Left Front
17
Export Lighting
18
Rear Door Modules
19
Stoplamps
20
Neutral Safety Back
-
up
21
Audio
22
Retained Accessory Power
for Sunroof
23
Not Used
24
Not Used
25
Passenger Door Module
26
Fuel Door/Trunk Release (Body)
27
Interior Lamps
28
Rear HVAC Blower
Minifuses
Usage
29
Ignition Switch
30
Not Used
31
Heated Seat Right Front
32
Continuous Variable Road
Sensing Suspension
33
Heating, Ventilation,
Air Conditioning
34
Ignition 3 Rear
35
Antilock Braking System
36
Turn Signal/Hazard
37
Heated Seat Right Rear
38
Dash Integration Module
Micro Relays
Usage
39
Fuel Pump
40
Parking Lamps
41
Ignition 1
6-78
Micro Relays
Usage
42
Park Brake A
43
Park Brake B
44
Park Shift Interlock
45
Reverse Lamps
46
Retained Accessory Power
for Sunroof
47
Rear HVAC Blower
48
Suspension Dampers
49
Ignition 3
50
Fuel Tank Door Release
51
Interior Lamps
52
Trunk Release
53
Front Courtesy Lamps
54
Rear Courtesy Lamps
55
Electronic Level
Control Compressor
Mini Breakers
Usage
56
Power Seats
57
Power Windows
Mini Relays
Usage
58
Cigarette Lighter
59
Rear Defog
MaxiFuses
Usage
60
Park Brake
61
Rear Defog
62
Export Brake
63
Audio Amplifier
64
ELC Compressor/Exhaust
65
Cigar Lighter
66
Not Used
The spare fuses are located in numbers 69 through 74.
The fuse puller is located in number 75.