Buick Rendezvous - 2002 Fuse Box Diagram

Buick Rendezvous - 2002 Fuse Box Diagram

2-26
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS
-
210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation
of the device.
Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
PASS
-
Key III uses a radio frequency transponder in the
key that matches a decoder in your vehicle.
When the PASS
-
Key III system senses that someone is
using the wrong key, it shuts down the vehicle’s starter
and fuel systems. The starter will not work and fuel will
stop being delivered to the engine. Anyone using a
trial
-
and
-
error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
When trying to start the vehicle if the engine does not
start and the SECURITY message comes on, the key
may have a damaged transponder. Turn the ignition off
and try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty.
See your dealer who can service the PASS
-
Key III to
have a new key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
If all the currently programmed keys are lost or do not
operate, you must see your dealer or a locksmith who
can service PASS
-
Key III to have keys made and
programmed to the system.
See your dealer who can service PASS
-
Key III to get a
new key blank that is a cut exactly as the ignition key
that operates the system.
2-44
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up
or down. When the turn is finished, the lever will
return automatically.
An arrow on the instrument
panel cluster and the
optional HUD display will
flash in the direction of the
turn or lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or a lane change, if the arrow
flashes faster than normal, a signal bulb may be burned
out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check for burned
-
out bulbs and check the
fuse (see “Fuses and Circuit Breakers” in the Index).
If you have a trailer towing option with added wiring for
the trailer lamps, the signal indicator will flash at a
normal rate even if a turn signal bulb is burned out.
Check the front and rear turn signal lamps regularly to
make sure they are working.
Turn Signal On Chime
If either turn signal is left on for more than 3/4 mile
(1.2 km), a chime will sound to let the driver know to
turn it off.
If you need to leave the signal on for more than 3/4 mile
(1.2 km), turn off the signal and then turn it back on.
2-71
If the air inflator system does not turn on, the fuse may
be blown or installed incorrectly. See “Fuses and Circuit
Breakers” in the Index or see your dealer for service.
Your air inflator will automatically shut off after about
10 minutes. To reset, press the ON switch again.
Don’t run your air inflator for longer than 30 minutes at
one time. If you do, you may damage the system. After
30 minutes, wait at least 10 minutes before restarting the
air inflator.
To turn off the inflator, press OFF and detach the hose
from the inflated object first, then from the outlet.
Replace the protective cap. Place the inflator kit tools in
the pouch, and store in the glove box.
Accessory Power Outlets
Accessory power outlets can be used to plug in electrical
equipment such as a cellular telephone, CB radio, etc.
There are two front power outlets when the cigarette
lighter is not in use. They are located on the floor
console in the cell phone storage compartment.
There are also two rear power outlets. One is located in
the rear of the floor console below the vents. The other
is located in the rear of the vehicle on the driver’s side
behind the access door.
Pull the cover down to use an accessory power outlet.
When not in use, always cover the accessory power
outlets with the protective cap.
The accessory power outlets will only operate while the
ignition is on and for 10 minutes after turning the
ignition off. If you would like to operate an accessory
for an extended period of time, see your dealer for
more information.
NOTICE:
When using the accessory power outlets:
D
Maximum load of any electrical equipment
should not exceed 20 amps.
D
Be sure to turn off any electrical equipment
when not in use. Leaving electrical
equipment on for extended periods can
drain your battery.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result in
blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information on
the accessory power outlets.
2-81
The main components of the instrument panel are the following:
A.
Exterior/Interior Lamps Control
B.
Turn Signal/Multifunction Lever
C.
Hazard Warning Flasher Switch
D.
Instrument Panel Cluster
E.
Shift Lever
F.
Instrument Panel Vents
G.
Audio System
H.
Audio Steering Wheel Controls (If Equipped)
I.
Head
-
Up Display Switch (Option) and Driver
Information Center (DIC) Controls (If Equipped)
J.
Hood Release
K.
Ignition Switch
L.
Comfort Controls
M. Center Console Switchbank
N.
Front Armrest Storage
O.
Ashtray/Cigarette Lighter/Accessory Power
Outlet/Cell Phone Storage/Purse Storage/Cupholders
P.
Instrument Panel Fuse Block
Q.
Glove Box
2-124
To adjust the HUD so you can see it properly:
1.
Start your engine and turn the dimmer knob to the
desired HUD image brightness.
The brightness of the HUD image is determined by
the ambient light conditions in the direction your
vehicle is facing and where you have the HUD
dimmer knob set. If you are facing a dark object or a
heavily shaded area, your HUD may anticipate that
you are entering a dark area and may begin to dim.
2.
Adjust the driver’s seat. If you change your seat
position later, you may have to readjust your HUD.
3.
Press the UP or DN buttons until the HUD image is
easy to see and then press the DN button until the
HUD image is as low as possible, but, remains in full
view straight ahead near the front bumper.
The HUD image can only be adjusted up and down,
not side
-
to
-
side.
4.
To turn the image off, turn the dimmer knob
counterclockwise to OFF.
If the sun comes out or it becomes cloudy, you may need
to adjust the HUD brightness again using the dimmer
knob. Polarized sunglasses could make the HUD image
harder to see.
When you first start the vehicle the display will show
BUICK and the Buick logo for a few seconds. If it is
cold outside, this display may stay on for up to a minute.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity of
the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry it.
Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you can’t see the HUD image,
check one of the following:
D
The HUD unit is covered,
D
the HUD dimmer knob is adjusted correctly,
D
the HUD image is adjusted to the proper height,
D
ambient light (in the direction your vehicle is facing)
is low, or
D
a fuse is blown. See “Fuses and Circuit Breakers” in
the Index.
Keep in mind that your windshield is part of the HUD
system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD or
your HUD image may look blurred and out of focus.
5-4
2.
Get the vehicles close enough so the jumper cables
can reach, but be sure the vehicles aren’t touching
each other. If they are, it could cause a ground
connection you don’t want. You wouldn’t be able
to start your vehicle, and the bad grounding could
damage the electrical systems.
To avoid the possibility of the vehicles rolling, set
the parking brake firmly on both vehicles involved
in the jump starting procedure. Put an automatic
transaxle in PARK (P) or a manual transaxle in
NEUTRAL before setting the parking brake.
NOTICE:
If you leave your radio on, it could be badly
damaged. The repairs wouldn’t be covered by
your warranty.
3.
Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or in the accessory power outlet(s). Turn off
the radios and all lamps that aren’t needed. This will
avoid sparks and help save both batteries. And it
could save your radio!
4.
Open the hoods and locate the batteries. Find the
positive (+) and negative (
-
) terminals on
each vehicle.
You will not need to access your battery for
jump starting. Your vehicle has a remote positive (+)
jump starting terminal for that purpose. The terminal
is located under a tethered cap at the front of the
underhood fuse and relay center. See “Engine
Compartment Overview” in the Index for more
information on location.
Flip the cap up to access the remote positive (+)
terminal. You should always use the remote
positive (+) terminal instead of the positive (+)
terminal on the battery.
CAUTION:
An electric fan can start up even when the engine
is not running and can injure you. Keep hands,
clothing and tools away from any underhood
electric fan.
6-10
Engine Compartment Overview
When you lift the hood, you’ll see these items:
A.
Underhood Fuse and Relay Center
B.
Remote Positive (+) Terminal
C.
Power Steering Fluid Reservoir
D.
Automatic Transaxle
Fluid Dipstick
E.
Brake Master Cylinder
F.
Windshield Washer
Fluid Reservoir
G. Battery
H.
Radiator Pressure Cap
I.
Engine Oil Fill Cap
J.
Engine Oil Dipstick
K.
Engine Air Cleaner/Filter
L.
Engine Coolant Reservoir
6-30
Adding Washer Fluid
The windshield washer fluid
reservoir is located in the
engine compartment on the
passenger’s side of the
vehicle, near the fuse and
relay center.
Open the cap with the washer
symbol on it. Add washer
fluid until the tank is full.
NOTICE:
D
When using concentrated washer fluid,
follow the manufacturer’s instructions for
adding water.
D
Don’t mix water with ready
-
to
-
use washer
fluid. Water can cause the solution to freeze
and damage your washer fluid tank and
other parts of the washer system. Also,
water doesn’t clean as well as washer fluid.
D
Fill your washer fluid tank only
three
-
quarters full when it’s very cold. This
allows for expansion if freezing occurs, which
could damage the tank if it is completely full.
D
Don’t use engine coolant (antifreeze) in
your windshield washer. It can damage
your washer system and paint.
6-61
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by an internal circuit
breaker in the floor console fuse block. An electrical
overload will cause the lamps to go on and off, or in
some cases to remain off. If this happens, have your
headlamp wiring checked right away.
Windshield Wipers
The windshield wiper motor is protected by an internal
circuit breaker and a fuse. If the motor overheats due to
heavy snow, etc., the wiper will stop until the motor
cools. If the overload is caused by some electrical
problem, be sure to get it fixed.
Power Windows and Other Power Options
Circuit breakers in the floor console fuse block protect
the power windows and other power accessories.
When the current load is too heavy, the circuit breaker
opens and closes, protecting the circuit until the problem
is fixed.
6-62
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
If you ever have a problem on the road and don’t have a
spare fuse, you can borrow one that has the same
amperage or use one of the spare fuses in the underhood
fuse and relay center. Just pick some feature of your
vehicle that you can get along without
--
like the radio
or cigarette lighter
--
and use its fuse, if it is the right
amperage. Replace it as soon as you can.
There are two fuse blocks in your vehicle: the floor
console fuse block and the underhood fuse and
relay center.
Floor Console Fuse Block
The floor console fuse block is located to the left of the
glove box near the floor.
The fuses marked spare are available if a replacement
fuse is needed.
Pull the door open to access the fuse block.
6-63
Fuses
Usage
1
Fuse Puller
2
Steering Wheel Radio Controls
3
Power Door Locks
4
Spare
5
Spare
6
Spare
7
Spare
8
Spare
9
Spare
10
Turn Signal and Hazard
Lamp Flashers
11
Power Seats
12
Electronic Level
Control (ELC) Compressor
13
Liftglass and Endgate
14
Rear Auxiliary Power Outlet
15
Electronic Level Control (ELC)
Compressor Relay and
Height Sensor
Fuses
Usage
16
Heated Mirrors
17
Power Mirrors
18
Ignition 1 Module
19
Turn Signal Switch and
NSBU Switch
21
Rear Defogger
22
Air Bag Module
24
Canister Vent Solenoid and
TCC Switch
25
HVAC Blower Motor
26
HVAC Mode and Temperature
Motors and Head
-
Up Display
28
Not Used
29
Windshield Wipers and Washer
30
Instrument Panel Cluster,
BCM, PASS
-
Key
R
III
31
Park Lock Ignition Key Solenoid
32
Rear Window Wiper/Washer
34
Power Sunroof
6-64
Fuses
Usage
35
Power Windows
36
Map Lamps, Courtesy Lamps and
Instrument Panel Lights
37
Radio
38
UQ3 Radio Amplifier
39
Head
-
Up Display
40
Hazard Flashers
41
Instrument Panel Cluster, HVAC
Control, Security LED and
Remote Keyless Entry Module
42
PASS
-
Key
R
III
44
Body Control Module (BCM)
Relays
Usage
20
Rear Defogger Relay
23
IGN3 Relay
27
Accessory Relay
33
Retained Accessory Power Relay
Diode
43
Accessory Diode
Underhood Fuse Block
This fuse block is located in the engine compartment, on
top of the windshield washer fluid reservoir.
See “Engine Compartment Overview” in the Index for
more information on location.
The fuses marked spare are available if a replacement
fuse is needed.
To remove the cover, press the two tabs in and lift up
the cover.
6-65
Mini Fuses
Usage
1
Fuel Pump
2
Air Conditioning
Compressor Clutch
3
Horn
4
Engine Controls
-
Emissions
and Sensors
5
Power Control Module
(PCM)
-
Battery Power
Mini Fuses
Usage
6
Anti
-
Lock Brakes (ABS)
Control Module
7
Transaxle Solenoids
8
Spare
9
ABS Solenoid Valves
10
Oxygen
Sensors
-
Emissions Control
11
Injectors
12
Spare
13
Engine Controls
14
Daytime Running Lamps (DRL)
15
Passenger’s Low
-
Beam Headlamp
16
Spare
17
Driver’s Low
-
Beam Headlamp
18
Driver’s High
-
Beam Headlamp
19
Ignition Switch Battery Power
20
Parking Lamps
-
Front and Rear
21
Air Pump
-
Emissions Controls
22
Spare
23
Passenger’s High
-
Beam Headlamp
6-66
Mini Fuses
Usage
24
Spare
25
Spare
26
Front Fog Lamps
27
Ignition Relay, Neutral
Start Switch, Powertrain
Control Module (PCM)
28
Battery Control
Module
-
Battery Power
29
Spare
30
All
-
Wheel Drive (AWD) Module
31
Cruise Control
32
Front Power
Outlets/Lights, OnStar
R
33
Automatic Transaxle Shift Lock
Control System
34
Spare
J
-
Style Fuse
Usage
35
Starter Solenoid Battery Fuse
36
ABS Motor
37
Spare
J
-
Style Fuse
Usage
38
Spare
39
Engine Cooling Fan
40
Engine Cooling Fan
41
Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
42
Main Battery Fuse for Heated
Seats, Air
43
Spare
44
Spare
45
Main Battery Fuse for Power
Outlets, Level Control,
Power Seats and Mirrors and
Body computer
46
Spare
47
Main Battery Fuse for HVAC
Blower and Ignition 3 relay
48
Main Battery fuse for Ignition
Switch, Radio, Heads
-
Up Display,
Remote Keyless Entry (RKE),
Instrument Cluster, Air
Conditioning and Body Computer
6-67
Maxi Breaker
Usage
49
Spare
Micro Relay
Usage
50
Horn
51
Fuel Pump
52
Air Conditioning Clutch
53
Daytime Running Lamps (DRL)
54
Low
-
Beam Headlamps
55
Parking Lamps
56
High
-
Beam Headlamps
57
Fog Lamps
Mini Relay
Usage
58
Starter Relay
59
Cooling Fan
60
Ignition 1 Relay
61
Cooling Fan
62
Cooling Fan
63
Air Pump
Spare Fuses
Usage
64
Spare
65
Spare
66
Spare
67
Spare
68
Spare
69
Spare
Fuse Puller
70
Fuse Puller
Diode
Diode for Air Conditioning
Compressor Clutch