Buick Park Avenue - 2002 Fuse Box Diagram

Buick Park Avenue - 2002 Fuse Box Diagram

2-21
Testing the Alarm
The alarm can be tested by following these steps:
1.
From inside the vehicle, roll down the driver’s
window and open the driver’s door.
2.
Activate the system by locking the doors using the
power door lock switch while the door is open, or
using the remote keyless entry transmitter.
3.
Get out of the car, close the door and wait for the
SECURITY light to go out.
4.
Then reach in through the window, unlock the door
with the manual door lock and open the door. This
should set off the alarm.
If the alarm does not sound when it should, but the
vehicle’s lamps flash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse, see
Fuses and Circuit Breakers” in the Index.
If the alarm does not sound or the vehicle’s lamps do not
flash, the vehicle should be serviced by an authorized
service center.
PASS
-
Key
R
III
Your vehicle is equipped
with the PASS
-
Key III
(Personalized Automotive
Security System)
theft
-
deterrent system.
PASS
-
Key III is a passive
theft
-
deterrent system. This
means you don’t have to do
anything different to arm or
disarm the system. It works
when you insert or remove
the key from the ignition.
Your PASS
-
Key III system operates on a radio
frequency subject to Federal Communications
Commission (FCC) Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
2-22
This device complies with RSS
-
210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.
Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
PASS
-
Key III uses a radio frequency transponder in the
key that matches a decoder in your vehicle.
When the PASS
-
Key III system senses that someone is
using the wrong key, it shuts down the vehicle’s starter
and fuel systems. The starter will not work and fuel will
stop being delivered to the engine. Anyone using a
trial
-
and
-
error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
When trying to start the vehicle if the engine does not
start and the SECURITY light comes on, the key may
have a damaged transponder. Turn the ignition off and
try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty.
See your dealer who can service the PASS
-
Key III
to have a new key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS
-
Key III to have new
keys made. To program additional keys you will need
two current driver’s keys. You must add a step to the
following procedure. After Step 2 repeat Steps 1 and 2
with the second current driver’s key. Then continue
with Step 3.
To program the new key, do the following:
1.
Verify that the new key has “PK3” stamped on it.
2.
Insert the current driver’s key in the ignition and
start the engine. If the engine will not start, see your
dealer for service.
2-39
As you signal a turn or a lane change, if the arrows flash
at twice the normal rate, this may indicate that a signal
bulb may be burned out and other drivers won’t see your
turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in the Index) and for burned
-
out bulbs.
If you have a trailer towing option with added wiring for
the trailer lamps, the signal indicator will flash even if a
turn signal bulb is burned out. Check the front and rear
turn signal lamps regularly to make sure they are
working. You do not need to add a different flasher.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the turn
signal. To turn off the chime, move the turn signal lever
to the off position.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high or
high to low, pull the turn signal lever toward you, then
release it.
When the high beams are
on, a light on the instrument
panel cluster will also be on.
If your vehicle is equipped
with HUD, this light
will also appear in the
display area.
Flash-to-Pass Feature
This feature lets you use your high
-
beam headlamps to
signal a driver in front of you that you want to pass. It
works even if your headlamps are off.
To use it, pull the turn signal lever toward you, but not
so far that you hear a click.
If your headlamps are off or on low beam, your
high
-
beam headlamps will turn on. They’ll stay on as
long as you hold the lever toward you and the
high
-
beam indicator on the instrument panel cluster
comes on. Release the lever to turn the high
-
beam
headlamps off.
2-61
Auxiliary Power Outlets
The auxiliary power outlets can be used to plug in
electrical equipment such as a cellular telephone or
CB radio.
Your vehicle has two power outlets located in the rear
storage area of the front center console. See “Front
Center Console” in the Index for more information
on location.
Your vehicle may have a small cap that must be pulled
down to access the auxiliary power outlet. If it does,
when not using the outlet be sure to cover it with the
protective cap.
The auxiliary power outlets will only operate while
the ignition key is in RUN and for 10 minutes after
turning the ignition off. If you would like to operate an
accessory for an extended period of time, contact your
dealer for more information.
NOTICE:
When using auxiliary power outlets:
D
Maximum load of any electrical equipment
should not exceed 15 amps.
D
Be sure to turn off any electrical equipment
when not in use. Leaving electrical equipment
on for extended periods can drain the battery.
Certain electrical accessories may not be compatible to
the auxiliary power outlet and could result in blown
vehicle or adapter fuses. If you experience a problem see
your dealer for additional information on auxiliary
power outlets.
2-99
Care of the HUD
Clean the inside of the windshield as necessary to
remove any dirt or film that reduces the sharpness or
clarity of the HUD image.
To clean the HUD lens, spray household glass cleaner
on a soft, clean cloth. Gently wipe and dry the HUD
lens. Do not spray cleaner directly on the lens to avoid
cleaner leaking inside the unit.
If You Can’t See The HUD Image When the
Ignition is On
If the ignition is on and you can’t see the HUD image,
check to see if:
D
The headlamps are on.
D
Something is covering the HUD unit.
D
The HUD dimmer control is adjusted properly.
D
The HUD image is adjusted to the proper height.
D
A fuse is blown. See “Fuses and Circuit Breakers” in
the Index.
Keep in mind that your windshield is part of the HUD
system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD or
your HUD image may look blurred or out of focus.
Ultrasonic Rear Parking Assist
(URPA) (Option)
Ultrasonic rear parking assist can help you to determine
how close an object is to your rear bumper within a
given area, making parking easier.
The URPA display is located inside the vehicle, above
the rear window. It has three color
-
coded lights that can
be seen through the rearview mirror.
How the System Works
Ultrasonic rear parking assist comes on automatically
when the shift lever is moved into REVERSE (R) and
the vehicle speed is less than 3 mph (5 km/h). When the
system comes on, the three lights on the display will
illuminate to let you know that the system is working.
URPA senses how close your vehicle is to an object. The
distance is determined by the four rear sensors located
on the bumper. When shifting into REVERSE (R) and
an object is detected, one of the following will occur:
D
At 5 ft. (1.5 m) an amber light will come on.
D
At 40 in. (1.0 m) two amber lights will come on.
D
At 20 in. (0.5 m) two amber lights and a red light
will come on and a continuous chime will sound.
D
At 1 ft. (0.3 m) the chime will still be going
continuously and all three lights will flash.
6-11
Engine Compartment Overview
When you open the hood on the 3800 (L36) engine (3800 Supercharged (L67) engine similar), here’s what you will see:
A. Battery
B.
Underhood Fuse Block
C.
Radiator Pressure Cap
D.
Engine Oil Dipstick
E.
Engine Oil Fill Cap
F.
Automatic Transaxle
Fluid Dipstick
G.
Brake Master Cylinder Reservoir
H.
Windshield Washer
Fluid Reservoir
I.
Engine Coolant Recovery Tank
J.
Engine Air Cleaner/Filter
6-67
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of damage
caused by electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
There are three fuse blocks in your vehicle: the
instrument panel fuse block located under the instrument
panel, the underhood fuse block located in the engine
compartment on the passenger’s side of the vehicle and
the rear fuse block, located under the rear seat.
6-68
Main and Auxiliary Instrument Panel Fuse Blocks
The main and auxiliary instrument panel fuse blocks are
located on the passenger’s side of the vehicle, under the
instrument panel. Lamps, connectors and the HVAC
duct temperature sensors may need to be disconnected
and removed to allow access to these fuse blocks.
Remove the hush panel on the passenger’s side to reveal
the fuses by performing the following steps:
1.
Remove the two screws located along the front edge
of the panel.
2.
Lower the hush panel.
3.
Remove the fuse block cover.
4.
Place the wide end of the fuse puller over the plastic
end of the fuse.
5.
Squeeze the ends over the fuse and pull it out.
When finished, reinstall the fuse block cover and the
hush panel. Reinstall lamps, connectors and HVAC duct
temperature sensors if they were removed.
Main Instrument Panel Fuse Block
Fuse
Usage
SBM
Interior Lamps
PDM
PDM Module
A/C
HVAC Motor, HVAC Mix Motors
6-69
Fuse
Usage
IGN SEN
Electrochromic Mirror, Driver
HTS Seat, Rear Defog Relay,
MEM Module, Cool LVL Sensor,
Pass Heated Seat
ELC
HVAC Flat Pk Mtrs, Electronic
Level Control Sensor, Electronic
Level Control Sensor (R Bec)
ABS
Anti
-
Lock Brake System Module
HVAC
HVAC Main Con Head,
HVAC Programmer, Instrument
Panel Cluster
CR CONT
Stepper Motor Cruise,
Cruise Switch
HUD
Head
-
Up Display Switch,
Head
-
Up Display
CSTR/SBM
HVAC Programmer, Instrument
Panel Cluster, SBM (275 to LCM)
(1135 to BTSI SL)
Fuse
Usage
LP PK L
Underhood Lamp, Left Park/
Sidemarker, Left Park/Turn Lamp,
SBM, Left Tail Signal Lamp,
Left Tail/Stoplamp,
Left Rear Sidemarker
LP PK R
Right Park/Sidemarker Lamp,
Right ParK/Turn Lamp, Right
Tail/Sign Lamp, Right Tail/Sto-
plamp, Right Rear Sidemarker,
Stop/Taillamp, Tail/Signal Lamp,
License Lamp, RFA
RUN
Run/Accessory
WSW
Wiper Motor
Blank
Not Used
WSW/RFA
Wiper Switch, RFA, Rain Sense
B/U LP
Electrochromic Mirror,
Back
-
Up Lamps
6-70
Auxiliary Instrument Panel Fuse Block
Fuse
Usage
PERIM LP
Perimeter Lamps
ACCY
Accessory
IGN 3
Ignition 3
Underhood Fuse Block
There are additional fuses located in the engine
compartment on the passenger’s side of the vehicle. See
“Engine Compartment Overview” in the Index for more
information on location.
To check the fuses in this underhood fuse block, turn the
knob counterclockwise and remove the cover. There is a
chart inside the cover that explains the features and
controls governed by each fuse and relay.
6-71
Minifuses
Usage
1
Air Sol
2
SBM, LCM
3
Turn Signal
4
Pre
-
Oxygen Sensor, Post
-
Oxygen
Sensor
5
Air Bag (SIR)
Minifuses
Usage
6
Powertrain Control Module
7
Air Conditioning Clutch
8
Ignition Feed
9
Horn Relay
10
Spare
11
Spare
12
Injectors #1
-
6
13
C
-
31
14
Right High Beam
15
Spare
16
Left High Beam
17
Spare
18
Right Low Beam
19
Left Low Beam
20
Stop
21
Fuel Pump Relay (Wire in BEC)
6-72
Minifuses
Usage
22
Run/Crank
23
Powertrain Control Module
24
Parking Lamp
25
Hazard Flashers
26
Spare
27
Spare
28
ABS #2
Mini Relays
Usage
29
Ignition
30
Horn
31
Cool Fan #2
32
Starter
33
Air Pump
34
Cool Fan SP
35
Cool Fan 1
Micro Relays
Usage
36
Air Conditioning Clutch
37
Fuel Pump
Maxifuses
Usage
38
Bat #1
39
Blower Motor
40
Cool Fan 2
41
Headlamp
42
BAT #2
43
Ignition
44
Starter
45
ABS
46
Fuse Puller
6-73
Removing the Rear Seat Cushion
NOTICE:
A fuse center is located under the rear seat
cushion. To help avoid damage to the fuse center,
be careful when removing or reinstalling the
seat cushion.
To remove the rear seat cushion, do the following:
1.
Pull up on the front of the cushion to release the
front hooks.
2.
Pull the cushion up and out toward the front of
the vehicle.
CAUTION:
A safety belt that isn’t properly routed through
the seat cushion or is twisted won’t provide the
protection needed in a crash. If the safety belt
hasn’t been routed through the seat cushion at
all, it won’t be there to work for the next
passenger. The person sitting in that position
could be badly injured. After reinstalling the seat
cushion, always check to be sure that the safety
belts are properly routed and are not twisted.
6-75
Rear Compartment Fuse Block
Additional fuses are located in the fuse center under the
rear seat.
Mini Relay
Usage
1
Heated Backlite
Micro Relays
Usage
2
Retained Accessory Power (RAP)
3
Trunk Release
4
Electronic Level Control
Circuit Breakers
Usage
5
Power Seat
6
Electronic Level Control Sensor,
Electronic Level Control
Compressor Solenoid
Minifuses
Usage
7
Crank
8
Auxiliary Outlet
9
Powertrain Control Module
for Cruise
10
SBM Module
11
Radio/Phone
12
Sunroof
13
Spare
14
CD Changer, Phone
15
Driver Door Module
16
Spare