Cadillac Seville - 2001 Fuse Box Diagram

Cadillac Seville - 2001 Fuse Box Diagram

2-19
Testing the Alarm
1.
From inside the vehicle, roll down the window, then
get out of the vehicle, keeping the door open.
2.
From outside of the vehicle, with the door open, lock
the vehicle using the power door lock or the RKE
system and close the door. Wait 30 seconds until the
SECURITY lamp goes off.
3.
Reach in and unlock the door using the manual lock
and open the door. The horn will sound and the
hazard lights will flash.
You can turn off the alarm by unlocking the driver’s
door with your key, using the unlock button on the RKE
transmitter or by starting the car with a valid key.
If the alarm does not sound when it should, check to see
if the horn works. The horn fuse may be blown. To
replace the fuse, see “Fuses and Circuit Breakers” in the
Index. If the fuse does not need to be replaced, you may
need to have your vehicle serviced.
To reduce the possibility of theft, always arm the
theft
-
deterrent system when leaving your vehicle.
Valet Lockout Switch
This switch is located inside the glove box on the left
side. Pressing this switch to ON will disable the use of
the trunk, fuel door and garage door opener.
Pressing this switch to
OFF will enable these
features for use.
Locking the glove box with your key will also help to
secure your vehicle. The remote keyless entry
transmitter can’t open the trunk or fuel door if the valet
lockout switch is in the ON position.
2-21
If the engine does not start, and the key appears to be
undamaged, try another ignition key. At this time, you
may also want to check the fuse (see “Fuses and Circuit
Breakers” in the Index). If the engine still does not start
with the other key, your vehicle needs service. If your
vehicle does start, the first key may be faulty. See your
dealer who can service the PASS
-
Key III to have a new
key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS
-
Key III to have new
keys made. To program additional keys you will require
two current driver’s keys (black in color). You must add
a step to the following procedure. After Step 2 repeat
Steps 1 and 2 with the second current driver’s key.
Then continue with Step 3.
To program the new key:
D
Insert the current driver’s key (black in color) in the
ignition and start the engine. If the engine will not
start see your dealer for service.
D
After the engine has started, turn the key to OFF,
and remove the key.
D
Insert the key to be programmed and turn it to ON
within ten seconds of removing the previous key.
D
The SECURITY light will turn off once the key has
been programmed. It may not be apparent that the
SECURITY light went on due to how quickly the
key is programmed.
D
Repeat the Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the SECURITY light comes
on and stays on, you will be able to restart your engine
if you turn it off. Your PASS
-
Key III system,
however, is not working properly and must be serviced
by your dealer. Your vehicle is not protected by the
PASS
-
Key III system at this time.
If you lose or damage a PASS
-
Key III key, see your
dealer to have a new key made.
2-39
Turn and Lane Change Signals
To signal a turn, move the lever on the left side of the
steering wheel all the way up or down. The lever returns
automatically when the turn is complete.
An arrow located on the
instrument panel cluster will
flash in the direction of the
turn or lane change.
Raise or lower the lever until the arrow starts to flash to
signal a lane change. Hold it there until the lane change
is complete. The lever returns when it is released.
If the turn signal is left on, a warning chime will sound
and the Driver Information Center (DIC) will display
TURN SIGNAL ON (after driving about a mile) to
remind you to turn it off.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned
-
out signal bulb.
Other drivers won’t see the turn signal.
Replace burned
-
out bulbs to help avoid possible
accidents. Check the fuse (see “Fuses and Circuit
Breakers” in the Index) and check for burned
-
out bulbs
if the arrow fails to work when signaling a turn.
Headlamp High/Low-Beam Changer
When the low
-
beam headlamps are on, push the turn
signal lever away from you to change the headlamps to
high beam.
This light on the instrument
panel cluster will be on,
indicating high
-
beam usage.
Pull the turn signal lever toward you to return to
low
-
beam headlamps.
2-60
Accessory Power Outlets
The accessory power outlets are located at the rear of
the center console and on the lower inboard carpeted
panel on the passenger’s side of the vehicle. When the
ignition is on, you can plug in accessories that require
electrical power.
The outlets can be used to plug in electrical equipment
such as a cellular telephone, CB radio, etc. Follow the
proper installation instructions that are included with
any electrical equipment you install.
Certain power accessory plugs may not be compatible
to the power accessory outlet and could result in blown
vehicle or adapter fuses. If you experience a problem
see your dealer for additional information on the power
accessory plugs.
The accessory power outlet will only operate when the
ignition is in ON and for 10 minutes after turning the
ignition OFF. If you would like the accessory power
outlet to operate regardless of ignition position, and for
unlimited periods of time, see “Underhood Junction
Block” in the Index or see your dealer.
Leaving an accessory on for a long period of time, or a
fuse in the wrong place, can drain the vehicle’s battery.
NOTICE:
When using the accessory power outlet, the
maximum load of any electrical equipment
should not exceed 15 amps.
6-28
Power Steering Fluid
The power steering fluid
reservoir is located next
to the fuse relay center
on the passenger’s side of
the engine.
See “Engine Compartment Overview” in the Index
for more information on location.
When to Check Power Steering Fluid
It is not necessary to regularly check power steering
fluid unless you suspect there is a leak in the system or
you hear an unusual noise. A fluid loss in this system
could indicate a problem. Have the system inspected
and repaired.
How to Check Power Steering Fluid
Turn the key off, let the engine compartment cool down,
wipe the cap and the top of the reservoir clean, then
unscrew the cap and wipe the dipstick with a clean rag.
Replace the cap and completely tighten it. Then remove
the cap again and look at the fluid level on the dipstick.
The level should be at the FULL COLD mark. If necessary,
add only enough fluid to bring the level up to the mark.
What to Use
To determine what kind of fluid to use, see
“Recommended Fluids and Lubricants” in the
Maintenance Schedule booklet. Always use the proper
fluid. Failure to use the proper fluid can cause leaks and
damage hoses and seals.
Windshield Washer Fluid
What to Use
When you need windshield washer fluid, be sure to read
the manufacturer’s instructions before use. If you will be
operating your vehicle in an area where the temperature
may fall below freezing, use a fluid that has sufficient
protection against freezing.
6-29
Adding Washer Fluid
When your vehicle’s windshield washer fluid level
becomes low, a CHECK WASHER FLUID message will
appear on the Driver Information Center (DIC). You will
need to add fluid soon.
The windshield washer fluid reservoir is located next to
the fuse relay center on the passenger’s side of the
engine. See “Engine Compartment Overview” in the
Index for more information on location.
Open the cap labeled WASHER FLUID. Add washer
fluid until the tank is full.
NOTICE:
D
When using concentrated washer fluid,
follow the manufacturer’s instructions for
adding water.
D
Don’t mix water with ready
-
to
-
use washer
fluid. Water can cause the solution to freeze
and damage your washer fluid tank and
other parts of the washer system. Also,
water doesn’t clean as well as washer fluid.
D
Fill your washer fluid tank only
three
-
quarters full when it’s very cold.
This allows for expansion if freezing
occurs, which could damage the tank if
it is completely full.
D
Don’t use engine coolant (antifreeze) in
your windshield washer. It can damage
your washer system and paint.
6-66
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring has an individual fuse. An
electrical overload will cause the lamps to go on and off,
or in some cases to remain off. If this happens, have the
headlamp wiring checked right away.
Windshield Wiper Fuses
A circuit breaker protects the wiper motor. If the wiper
motor overheats due to heavy snow, the wipers will stop
until the motor cools and will then restart.
A MiniFuse
R
powers the wiper motor. If the MiniFuse
blows, there is an electrical problem. Be sure to have
it fixed.
Power Windows and Other Power Options
Circuit breakers protect the power windows. When the
current load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed or
goes away.
6-67
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of fires caused
by electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating. If a MaxiFuse should blow, see your dealer
for service immediately.
If you ever have a problem on the road and don’t have a
spare fuse, you can “borrow” one that has the same
amperage. Pick some feature of your vehicle that you
can get along without
--
like the radio or cigarette
lighter
--
and use its fuse, if it is the correct amperage.
Replace it as soon as you can.
The MaxiFuses are located in two Bussed Electrical
Centers (BEC), one located near the engine
compartment on the passenger’s side and the other
under the rear seat on the driver’s side. If a MaxiFuse
should blow, have your vehicle serviced by your
dealer immediately.
Underhood Junction Block
The front Bussed Electrical Center (BEC) is located
in the front of the engine compartment between the
windshield washer fluid reservoir and the power steering
fluid reservoir (on the passenger’s side). Lift the cover
to gain access.
Fuse 22 or 23 can be moved to the outer position to
enable the accessory power outlet or cigarette lighter
when the ignition is not on. See your dealer for
additional assistance, if needed.
6-68
Minifuses
Usage
1
ALDL
2
Accessory
3
Windshield Wipers
4
Not Used
5
Headlamp Low Beam Left
6
Headlamp Low Beam Right
Minifuses
Usage
7
Instrument Panel
8
Powertrain Control
Module Battery
9
Headlamp High Beam Right
10
Headlamp High Beam Left
11
Ignition 1
12
Fog Lamps
13
Transmission
14
Cruise Control
15
Coil MDL
16
Injector Bank #2
17
Not Used
18
Not Used
19
Powertrain Control
Module Ignition
20
Oxygen Sensor
21
Injector Bank #1
6-69
Minifuses
Usage
22
Auxiliary Power, (Cltr2)
23
Cigar Lighter
24
Daytime Running Lamps
25
Horn
26
Air Conditioner Clutch
Micro Relays
Usage
27
Headlamp High Beam
28
Headlamp Low Beam
29
Fog Lamps
30
Daytime Running Lamps
31
Horn
32
Air Conditioner Clutch
Mini Relays
Usage
33
Not Used
34
Accessory
35
Not Used
Mini Relays
Usage
36
Starter 1
37
Cooling Fan Secondary
38
Ignition 1
39
Cooling Fan Series/Parallel
40
Cooling Fan Primary
Maxibreaker
Usage
41
Starter
42
Export Use
MaxiFuses
Usage
43
Not Used
44
Antilock Brake System
45
Air Pump
46
Cooling Fan Secondary
47
Cooling Fan Primary
The spare fuses are located in numbers 48 through 52.
The fuse puller is located in number 53.
6-70
Removing the Rear Seat Cushion
NOTICE:
The battery and main fuse blocks are located
under the rear seat cushion. The battery’s
ground terminal and some relay wires are
exposed. To help avoid damage to the battery
and wires, be careful when removing or
reinstalling the seat cushion. Do not remove
covers from covered parts. Do not store anything
under the seat, as objects could touch exposed
wires and cause a short.
To Remove the Rear Seat Cushion
1.
Pull up on the front of the cushion to release the
front hooks.
2.
Pull the cushion up and out toward the front of
the vehicle.
To Reinstall the Rear Seat Cushion
6-72
Rear Underseat Bussed Electrical Center (BEC)
The rear BEC is located under the rear seat on the
driver’s side. The rear seat cushion must be removed to
access the BEC. See “Removing the Rear Seat Cushion”
in the Index.
Minifuses
Usage
1
Fuel Pump
2
Heater, Ventilation,
Air Conditioner Blower
3
Memory Seat, Tilt and
Telescoping Steering
4
Not Used
5
Driver Door Module
6-73
Minifuses
Usage
6
Heated Seat Left Rear
7
Power Tilt and
Telescoping Steering
8
Supplemental Inflation Restraint
9
Not Used
10
Lamps Park Right
11
Fuel Tank Ventilation Solenoid
12
Ignition 1
13
Lamps, Parking Left
14
Interior Lamp Dimmer Module
15
Navigation
16
Heated Seat Left Front
17
Export Lighting
18
Rear Door Modules
19
Stoplamps
20
Neutral Safety Back
-
up
21
Audio
22
Retained Accessory Power
for Sunroof
Minifuses
Usage
23
Not Used
24
Not Used
25
Passenger Door Module
26
Fuel Door/Trunk Release (Body)
27
Interior Lamps
28
Rear HVAC Blower
29
Ignition Switch
30
Not Used
31
Heated Seat Right Front
32
Continuous Variable Road
Sensing Suspension
33
Heating, Ventilation,
Air Conditioning
34
Ignition 3 Rear
35
Antilock Braking System
36
Turn Signal/Hazard
37
Heated Seat Right Rear
38
Dash Integration Module
6-74
Micro Relays
Usage
39
Fuel Pump
40
Parking Lamps
41
Ignition 1
42
Park Brake A
43
Park Brake B
44
Park Shift Interlock
45
Reverse Lamps
46
Retained Accessory Power
for Sunroof
47
Rear HVAC Blower
48
CVRSS Dampers
49
Ignition 3
50
Fuel Tank Door Release
51
Interior Lamps
52
Trunk Release
53
Front Courtesy Lamps
54
Rear Courtesy Lamps
55
Electronic Level
Control Compressor
Mini Breakers
Usage
56
Power Seats
57
Power Windows
Mini Relays
Usage
58
Cigarette Lighter
59
Rear Defog
MaxiFuses
Usage
60
Park Brake
61
Rear Defog
62
Export Brake
63
Audio Amplifier
64
ELC Compressor/Exhaust
65
Cigar Lighter
66
Not Used
The spare fuses are located in numbers 70 through 74.
The fuse puller is located in number 75.