Buick Park Avenue - 2001 Fuse Box Diagram

Buick Park Avenue - 2001 Fuse Box Diagram

2-19
Remember, the theft
-
deterrent system won’t activate if
you lock the doors with a key or use the manual door
lock. It activates only if you use a power door lock
switch with the door open, or with the remote keyless
entry transmitter. You should also remember that you
can start your vehicle with the correct ignition key if the
alarm has been set off.
Here’s how to avoid setting off the alarm by accident:
D
If you don’t want to activate the theft
-
deterrent
system, the vehicle should be locked with the door
key
after
the doors are closed.
D
Always unlock a door with a key, or use the remote
keyless entry transmitter. Unlocking a door any other
way will set off the alarm.
If you set off the alarm by accident, unlock any door
with your key. You can also turn off the alarm by
pressing the button with the unlock symbol on the
remote keyless entry transmitter. The alarm won’t stop
if you try to unlock a door any other way.
Testing the Alarm
The alarm can be tested by following these steps:
1.
From inside the vehicle, roll down the driver’s
window and open the driver’s door.
2.
Activate the system by locking the doors using the
power door lock switch while the door is open, or
using the remote keyless entry transmitter.
3.
Get out of the car, close the door and wait for the
SECURITY light to go out.
4.
Then reach in through the window, unlock the door
with the manual door lock and open the door.
This should set off the alarm.
If the alarm does not sound when it should, but the
vehicle’s lamps flash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse, see
Fuses and Circuit Breakers” in the Index.
If the alarm does not sound or the vehicle’s lamps do not
flash, the vehicle should be serviced by an authorized
service center.
2-21
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty.
See your dealer who can service the PASS
-
Key III to
have a new key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS
-
Key III to have new
keys made. To program additional keys you will need
two current driver’s keys (black in color). You add a
step to the following procedure. After Step 2 repeat
Steps 1 and 2 with the second current driver’s key.
Then continue with Step 3.
To program the new key:
1.
Insert the current driver’s key (black in color) in the
ignition and start the engine. If the engine will not
start, see your dealer for service.
2.
After the engine has started, turn the key to OFF, and
remove the key.
3.
Insert the key to be programmed and turn it to RUN
within 10 seconds of removing the previous key.
4.
The SECURITY light will turn off once the key has
been programmed. It may not be apparent that the
SECURITY light went on due to how quickly the
key is programmed.
5.
Repeat Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the SECURITY light comes
on and stays on, you will be able to restart your engine if
you turn it off. Your PASS
-
Key III system, however, is
not working properly and must be serviced by your
dealer. Your vehicle is not protected by the PASS
-
Key
III system at this time.
If you lose or damage a PASS
-
Key III key, see your
dealer to have a new key made.
2-37
As you signal a turn or a lane change, if the arrows flash
at twice the normal rate, this may indicate that a signal
bulb may be burned out and other drivers won’t see your
turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in the Index) and for burned
-
out bulbs.
If you have a trailer towing option with added wiring for
the trailer lamps, the signal indicator will flash even if a
turn signal bulb is burned out. Check the front and rear
turn signal lamps regularly to make sure they are
working. You do not need to add a different flasher.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the turn
signal. To turn off the chime, move the turn signal lever
to the off position.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high or high to
low, pull the turn signal lever toward you, then release it.
When the high beams are
on, a light on the instrument
panel cluster will also be on.
If your vehicle is equipped
with HUD, this light
will also appear in the
display area.
Flash-to-Pass Feature
This feature lets you use your high
-
beam headlamps to
signal a driver in front of you that you want to pass.
It works even if your headlamps are off.
To use it, pull the turn signal lever toward you, but not
so far that you hear a click.
If your headlamps are off or on low beam, your
high
-
beam headlamps will turn on. They’ll stay on as
long as you hold the lever toward you and the
high
-
beam indicator on the instrument panel cluster
comes on. Release the lever to turn the high
-
beam
headlamps off.
2-61
Sun Visors
Illuminated Visor Vanity Mirror
Your vehicle has illuminated visor vanity mirrors. When
you open the visor vanity mirror by pulling up, the
lamps turn on.
The brightness of the lamps can be adjusted by sliding
the switch. Your vehicle may also have visor vanity
mirrors for the rear seat passengers.
To block out glare, swing down the visors. The larger
sun visor can be removed from the center mount and
moved to the side, while the auxiliary sun visor remains
to block glare from the front.
The front side of the driver’s sun visor also contains a
pocket for map storage.
Auxiliary Power Outlets
Your vehicle may have one or two power outlets
depending on the type of front seat you have. If your
front seat has a fold
-
down armrest, the power outlet is
located in the center of the front seat below the cushion.
If your vehicle has front bucket seats with a center
console, you will find one outlet inside the storage
compartment and the other on the lower front edge of
the console.
These power outlets can be used to plug in electrical
equipment such as a cellular telephone or CB radio.
Follow the proper installation instructions that are
included with the equipment you install.
Certain power accessory plugs may not be compatible to
the auxiliary power outlet and could result in blown
vehicle or adapter fuses. If you experience a problem see
your dealer for additional information on the power
accessory plugs.
2-99
If You Can’t See The HUD Image When the
Ignition is On
If the ignition is on and you can’t see the HUD image,
check to see if:
D
The headlamps are on.
D
Something is covering the HUD unit.
D
The HUD dimmer control is adjusted properly.
D
The HUD image is adjusted to the proper height.
D
A fuse is blown. See “Fuses and Circuit Breakers” in
the Index.
Keep in mind that your windshield is part of the
HUD system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD or
your HUD image may look blurred or out of focus.
Ultrasonic Rear Parking
Assist (URPA) (Option)
Ultrasonic rear parking assist can help you to determine
how close an object is to your rear bumper within a
given area, making parking easier.
The URPA display is located inside the vehicle, above
the rear window. It has three color
-
coded lights that can
be seen through the rearview mirror.
How the System Works
Ultrasonic rear parking assist comes on automatically
when the shift lever is moved into REVERSE (R) and
the vehicle speed is less than 3 mph (5 km/h). When the
system comes on, the three lights on the display will
illuminate to let you know that the system is working.
URPA senses how close your vehicle is to an object. The
distance is determined by the four rear sensors located
on the bumper. When shifting into REVERSE (R) and
an object is detected, one of the following will occur:
6-66
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment can
keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of damage
caused by electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
There are three fuse blocks in your vehicle: the
instrument panel fuse block located under the instrument
panel, the underhood fuse block located on the
passenger’s side engine compartment and the rear fuse
block, located under the rear seat.
6-67
Instrument Panel Fuse Block and Bussed Electrical
Center (BEC)
The instrument panel fuse block and BEC are located
on the passenger’s side of the vehicle, under the
instrument panel.
Remove the hush panel on the passenger’s side to reveal
the fuses. To remove the panel, do the following:
1.
Remove the two 7 mm screws located along the front
edge of the panel.
2.
Lower the hush panel.
3.
Remove the cover. Now you can see the fuses and
replace them.
4.
Place the wide end of the fuse puller over the plastic
end of the fuse.
5.
Squeeze the ends over the fuse and pull it out.
When finished, reinstall the hush panel. Reinstall lamps,
connectors, and HVAC duct temperature sensors if they
were removed.
Instrument Panel Fuse Block
Fuse
Usage
SBM
Interior Lamps
PDM
PDM Module
A/C
HVAC Motor, HVAC Mix Motors
6-68
Fuse
Usage
IGN SEN
EC Mirror, Driver HTS Seat,
Rear Defog Relay, MEM Module,
Cool LVL Sensor,
Pass Heated Seat
ELC
HVAC Flat Pk Mtrs, ELC Sensor,
ELC Sensor (R Bec)
ABS
Anti
-
Lock Brake System Module
HVAC
HVAC Main Con Head,
HVAC Programmer, IPC
CR CONT
Stepper Motor CR, Cruise Switch
HUD
HUD Switch, HUD Display
CSTR/SBM
HVAC Programmer,
IPC (Cluster),
SBM (275 to LCM)
(1135 to BTSI SL)
Fuse
Usage
LP PK L
Underhood Lamp, L PK/
Sidemarker, L Park/Turn Lamp,
SBM, L Tail Signal Lamp,
L Tail/Stoplamp,
L Rear Sidemarker
LP PK R
Rt Pk/Sidemarker Lamp,
Rt PK/Turn Lamp, Rt Tail/Sign
Lamp, Rt Tail/Stoplamp, Rt Rear
Sidemarker, Stop/Taillamp,
Tail/Signal Lamp,
License Lamp, RFA
RUN
Run/Accessory
WSW
Wiper Motor
Blank
Not Used
WSW/RFA
Wiper Switch, RFA, Rain Sense
B/U LP
EC Mirror, Back
-
Up Lamps
6-69
Instrument Panel Bussed Electrical Center (BEC)
Fuse
Usage
PERIM LP
Perimeter Lamps
ACCY
Accessory
IGN 3
Ignition 3
Underhood Fuse Block
There are additional fuses located on the passenger’s
side of the engine compartment.
To check the fuses in this underhood fuse center, turn
the knob counterclockwise and remove the cover. There
is a chart inside the cover that explains the features and
controls governed by each fuse and relay.
6-70
Minifuses
Usage
1
Air Sol
2
SBM, LCM
3
Turn Signal
4
Pre
-
Oxygen Sensor,
Post
-
Oxygen Sensor
5
Air Bag (SIR)
6
PCM
Minifuses
Usage
7
AC Clutch
8
Ignition Feed
9
Horn Relay
10
Spare
11
Spare
12
Injectors #1
-
6
13
C
-
31
14
Right High Beam
15
Spare
16
Left High Beam
17
Spare
18
Right Low Beam
19
Left Low Beam
20
Stop
21
Fuel Pump Relay (Wire in BEC)
22
Run/CRK
23
PCM
6-71
Minifuses
Usage
24
Parking Lamp
25
Hazard Flashers
26
Spare
27
Spare
28
ABS #2
Mini Relays
Usage
29
Ignition
30
Horn
31
Cool Fan #2
32
Starter
33
Air Pump
34
Cool Fan SP
35
Cool Fan 1
Micro Relays
Usage
36
A/C CLU
37
Fuel Pump
Maxifuses
Usage
38
Bat #1
39
Blower Motor
40
Cool Fan 2
41
Headlamp
42
BAT #2
43
Ignition
44
Starter
45
ABS
46
Fuse Puller
6-72
Removing the Rear Seat Cushion
NOTICE:
A fuse center is located under the rear seat
cushion. To help avoid damage to the fuse center,
be careful when removing or reinstalling the
seat cushion.
To Remove the Rear Seat Cushion
1.
Pull up on the front of the cushion to release the
front hooks.
2.
Pull the cushion up and out toward the front
of the vehicle.
To Reinstall the Rear Seat Cushion
6-74
Rear Compartment Fuse Block
Additional fuses are located in the fuse center under
the rear seat.
Mini Relay
Usage
1
Heated Backlite
Micro Relays
Usage
2
RAP
3
Trunk Release
4
ELC
Circuit
Breakers
Usage
5
Power Seat
6
ELC Sensor,
ELC Compressor Solenoid
Minifuses
Usage
7
Crank
8
Auxiliary Outlet
9
PCM/CRU
10
SBM Module
11
Radio/Phone
12
Sunroof
13
Spare
14
CD Changer, Phone