Cadillac Eldorado - 2000 Fuse Box Diagram

Cadillac Eldorado - 2000 Fuse Box Diagram

2-13
Remember, the theft
-
deterrent system won’t activate if
you lock a door with a key or use the manual door lock.
It activates only if you use a power door lock switch or
the remote keyless entry transmitter.
To avoid activating the alarm by accident:
D
Always unlock a door with a key or use the remote
keyless entry transmitter. (Pressing the unlock button
on the remote keyless entry transmitter disables the
theft
-
deterrent system.) Unlocking a door any other
way will activate the alarm. Cycling the ignition
without disarming the theft
-
deterrent system will
also activate the alarm.
D
The vehicle should be locked with the door key
after
the doors are closed if you don’t want to activate the
theft
-
deterrent system.
If you activate the alarm by accident, unlock either door
with your key. You can also turn off the alarm by using
the unlock button of the remote keyless entry
transmitter. The alarm won’t stop if you try to unlock a
door any other way.
Testing the Alarm
1.
From inside the vehicle, roll down the window, then
get out of the vehicle, keeping the door open.
2.
From outside of the vehicle, with the door open, lock
the vehicle using the power door lock or the remote
keyless entry transmitter and close the door. Wait
30 seconds until the SECURITY light goes off.
3.
Reach in and unlock the door using the manual lock
and open the door. The horn will sound and the
headlamps will flash.
If the alarm does not sound when it should, check to see
if the horn works. The horn fuse may be blown. To
replace the fuse, see “Fuses and Circuit Breakers” in the
Index. If the fuse does not need to be replaced, you may
need to have your vehicle serviced.
To reduce the possibility of theft, always activate the
theft
-
deterrent system when leaving your vehicle.
2-15
If the engine does not start and the STARTING
DISABLED REMOVE KEY message is displayed in
the Driver Information Center, your key should be
checked for damage. Starting may be attempted with an
undamaged key immediately. See your dealer or a
locksmith for key service.
If the STARTING DISABLE REMOVE KEY and
WAIT 3 MINUTES messages are displayed, the key
should be cleaned. After three minutes, try again.
A START CAR message will appear at this time.
If the engine still does not start, wait three minutes and
try a duplicate key. At this time, fuses should be checked
(see “Fuses and Circuit Breakers” in the Index).
If the engine does not start with the duplicate key, your
vehicle needs service. See your dealer for service.
If the THEFT SYSTEM PROBLEM, CAR MAY NOT
START message is displayed during vehicle operation,
a fault has been detected in the system. This means the
PASS
-
Key II system is disabled and is not protecting
the vehicle. The vehicle usually restarts. See your dealer
for service.
If an ignition key is lost or damaged, see your dealer or
a locksmith to have a new key made.
New Vehicle “Break
-
In”
NOTICE:
Your vehicle doesn’t need an elaborate
“break
-
in.” But it will perform better in the
long run if you follow these guidelines:
D
Don’t drive at any one speed
--
fast or
slow
--
for the first 500 miles (805 km).
Don’t make full
-
throttle starts.
D
Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren’t yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-
in guideline every
time you get new brake linings.
D
Don’t tow a trailer during break
-
in.
See “Towing a Trailer” in the Index for
more information.
2-31
If the turn signal is left on, a warning chime will
sound and the Driver Information Center (DIC) will
display TURN SIGNAL ON (after driving about
1 mile (1.6 km/h)) to remind you to turn it off.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned
-
out signal bulb.
Other drivers won’t see the turn signal.
Replace burned
-
out bulbs to help avoid possible
accidents. Check the fuse (see “Fuses and Circuit
Breakers” in the Index) and for burned
-
out bulbs if the
arrow fails to work when signaling a turn.
Headlamp High/Low Beam Changer
This light located on the
instrument panel panel will
be on when the high beam
headlamps are in use.
Pull the turn signal lever all the way toward you and
then release it to change the headlamps from low beam
to high or from high beam to low.
Flash-To-Pass
This lets you use the high
-
beam headlamps to signal
the driver in front of you that you want to pass.
Pull the turn signal lever toward you to use.
When you do:
D
If the headlamps are either off or in the Daytime
Running Lamps (DRL) mode, the high
-
beam
headlamps will turn on. They’ll stay on as long as
you hold the lever there. Release the lever to turn
them off.
D
If the headlamps are on low beam, they will shift to
high beam and stay there. Pull the lever toward you
to return to low beam.
D
If the headlamps are on high beam, they will switch
to low beam. To return to high beam, pull the lever
toward you.
6-58
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring has an individual fuse which is
powered by a MaxiFuse
R
. An electrical overload will
cause the lamps to go on and off, or in some cases to
remain off. If this happens, have the headlamp wiring
checked right away.
Windshield Wiper Fuses
The windshield wiper motor is powered by a
MaxiFuse
R
. If the motor overheats due to heavy snow,
etc., the wipers will stop until the motor cools. If the
overload is caused by some electrical problem, be sure
to have it fixed.
Power Windows and Other Power Options
Circuit breakers protect the power windows and other
power accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting the
circuit until the problem is fixed or goes away.
6-59
MaxiFuse
R
/Relay Center
The MaxiFuses and relays are located next to the engine
compartment fuse block on the driver’s side of the
engine. To access the compartment fuse block, remove
the shroud cover. If a MaxiFuse should blow, have your
vehicle serviced by your dealer immediately.
MaxiFuse
(8
-
Way)
Usage
BODY 1
Road Sensing Suspension (RSS) Fuse
(ETC Only), Convenience Fuse, BATT
Fuse, Antenna Fuse, Passenger and
Driver Seat Belt Comfort Solenoids,
Trunk and Fuel Door Release
Solenoids and Relays, Door
Lock/Unlock Relays, Damper Relay
(ETC Only), Parking Lamp Relay,
Right and Left Park Fuse
BODY 2
Defog Relay, Pull
-
Down Fuse, Right
and Left Heated Seat Fuses, Electronic
Level Control (ELC) Relay, Heated
Mirror Fuse, Heated Backlite Fuse,
ELC Circuit Breaker
BODY 3
Controlled Power Relay, Controlled
Power Back
-
Up Relay, Cluster Fuse,
Passenger Zone Module (PZM) Fuse,
Radio Fuse, RAP Relay, Trunk and
Fuel Door Release Relay, High
-
Beam
Relay, Comfort Fuse, AMP Fuse
(Optional), Right and Left Bose
Relay (Optional)
6-60
MaxiFuse
(8
-
Way)
Usage
INADVERT
Inadvertent Power Relay, Interior
Lamps Fuse, Cigarette Lighter
-
1 Fuse,
Courtesy Lamp Relay
LAMPS
Headlamps Fuse/Relay, High/Low
Beam Control Relay, Fog Lamp Fuse,
DRL Fuse, Hazard Fuse, Mirror Fuse,
Inadvertent Power Relay, Right and
Left High
-
Beam Fuse, Right and Left
Low
-
Beam Fuse, Stoplamp Fuse,
Fog Lamp Relay, DRL Relay
IGN 1
Rear Ignition
-
1 Relay, Wiper Fuse,
Relay Ignition
-
1 Fuse, Supplemental
Inflatable Restraint (SIR) Fuse,
Accessory Relay
WINDOWS
Retained Accessory
Power (RAP) Relay
SEATS
Horn Relay, Driver and Passenger
Lumbar In/Out Relays, Driver and
Passenger Lumbar Up/Down Relays
MaxiFuse
(6
-
Way)
Usage
BATT 3
Steering Column Ignition Switch
BATT 2
Steering Column Ignition Switch
IGN 1
Front Ignition
-
1 Relay, Oxygen
Sensor 1 and 2 Fuse, Fuel Fuse, Cruise
Fuse, Fuel Pump Relay
BATT 1
Starter Relay and Solenoid,
Park/Reverse Fuse, Park Relay,
Powertrain Control Module (PCM)
Fuse, AC Compressor Fuse and Relay,
Fan Relays, Reverse Relay
BRAKES
Anti
-
Lock Brake System (ABS)
Brake Modulator
COOL FNS
Cooling Fan Relays 1 and 3
6-61
Power
Distribution
Block
Usage
DRL
Daytime Running Lamps (DRL)
HI/LO BEAM
High and Low
-
Beam Headlamps
HORN
Horn
FOG LPS
Fog Lamps
ACCESSORY
Accessories
HEAD LPS
Headlamps
Relays
INADVERT POWER RELAY
IGN 1 RELAY
STARTER RELAY
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of fires caused
by electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
If you ever have a problem on the road and don’t have a
spare fuse, you can “borrow” one that has the same
amperage. Pick some feature of your vehicle that you
can get along without
--
like the radio or cigarette
lighter
--
and use its fuse, if it is the correct amperage.
Replace it as soon as you can.
There are two fuse blocks in your vehicle: the
underhood fuse block and the rear compartment
fuse block.
6-62
Underhood Fuse Block
The underhood fuse block is located next to the air
cleaner on the driver’s side of the engine. Lift the cover
to gain access.
Fuse
Usage
CNR LPS
Cornering Lamp Switch, Right
and Left Cornering Lamps
INT LPS
Trunk Lamp, Courtesy Lamps,
Front Vanity Lamps, Glove Box
Lamp, Garage Door Opener,
Courtesy Lamp Relay
6-63
Fuse
Usage
CIG LTR1
Front and Rear Cigarette Lighters
L HDLP LO
Left Low
-
Beam Headlamp
R HDLP LO
Right Low
-
Beam Headlamp
L HDLP HI
Left High
-
Beam Headlamp
R HDLP HI
Right High
-
Beam Headlamp
FOG
Fog Lamp Relay, Right and Left
Fog Lamps, Headlamp Switch
HDLPS
Headlamp Relay, High/Low
-
Beam
Control Relay, Right and Left
Low/High
-
Beam Fuses
HAZARD
Electronic Flasher Module,
Turn/Hazard Switch, Right and
Left Front Turn Lamps, Right and
Left Rear Turn Lamps, Cluster
STOP
Stoplamp Switch, Centered
High
-
Mounted Stoplamp
(CHMSL), Turn Hazard Switch,
ABS Controller, Stepper Motor
Cruise Control
Fuse
Usage
MIRROR
Inadvertent Power Relay, Left
Outside Rearview Mirror Switch,
ALDL, Memory Mirror Module,
Dimmer Switch, Cluster
DRL
Daytime Running Lamp (DRL)
Relay, Left and Right Low Beam
in DRL Mode
IGN 0 (ENG)
Powertrain Control
Module (PCM)
CRANK
Powertrain Control
Module (PCM)
ABS
Anti
-
Lock Brake System
(ABS)/Traction Control System
IGN
-
1
Rear Ignition
-
1 Relay, Front Fog
Lamp Relay, Controlled Power
Backup Relay, DRL Relay,
Canister Vent Solenoid
WIPERS
Accessory Relay, Wiper Switch
A/C COMP
AC Compressor Relay,
Cooling Fan Relays 1, 2, 3,
Compressor Clutch
6-64
Fuse
Usage
PCM (BAT)
PCM
PARK/REV
Reverse Relay, Right and Left
Back
-
Up Lamps, Electrochromic
Mirror (in Header), Park Relay,
Automatic Transaxle Shift Lock
Control Switch
ECS
Transaxle Shift Solenoids,
Air Meter, Canister Purge, PCM,
Front Ignition
-
1 Relay
PCM (IGN)
Powertrain Control
Module (PCM)
DIS
Odd and Even Coil Packs
CRUISE
Stepper Motor Cruise Control,
Low Refrigerant Pressure Cutoff
Switch, Park Relay
Fuse
Usage
INJ
Injectors 1, 4, 6, 7
INJ
Injectors 2, 3, 5, 8
FUEL PUMP
Fuel Pump Relay, Fuel Pump
OXY SEN1
Oxygen Sensor Front
OXY SEN2
Catalytic Converter (CAT)
Rear Oxygen Sensor, Starter
Enable Relay
Relays
A/C COMP
RELAY
FUEL PUMP
RELAY
6-65
Rear Compartment Fuse Block
The fuse block is located on the front wall of the trunk
(behind the rear seat) on the driver’s side. Loosen the
four trunk trim fasteners and pull the trim away from the
fuse block to gain access.
Fuse
Usage
RLY IGN1
Cluster, Cruise in Stalk, Passenger
Zone Module (PZM), Torque
Converter Clutch (TCC) Switch
SIR
Sensing and Diagnostic
Module (SDM)
ELC
Electronic Level Control (ELC)
Relay, ELC Height Sensor
TURN
Electronic Flasher,
Turn/Hazard Switch
Fuse
Usage
CONSOLE
Rear Zone Blower, Right and Left
Heated Seat Switches (Optional)
RSS
Road Sensing Suspension (RSS)
Module (ETC Only)
IGN 0
-
BODY
PRNDL, PZM, Cluster, Air
Control Module (ACM), Upper
Zone Motor, Lower Zone Motor
(Optional), HVAC Solenoids,
Climate Control Panel, Rear
Defog Relay, ELC Relay
COMFORT
CD Player, Remote Keyless
Entry (RKE), Controlled
Power Relay, Air Control
Module (ACM), PZM
AMP (Optional)
Right and Left Hand Bose
Relay, Right and Left Front
Speakers (On Door), Right and
Left Rear Speakers
PZM
Passenger Zone Module (PZM)
6-66
Fuse
Usage
RADIO/PHONE
Radio Receiver, Radio Interface
Module (RIM) (Optional), Phone,
RAP Relay, Trunk Release Relay,
Fuel Door Release Relay,
High/Low
-
Beam Relay
CLUSTER
Steering Wheel Controls, Cluster
ACC
PZM, Electrochromic Mirror,
Rain Sensor (Optional),
Accessory Relay
HTD MIR
Right and Left Outside
Heated Mirror
HTD SEAT R
Passenger Heated Seat
Relay (Optional)
HTD SEAT L
Driver Heated Seat
Relay (Optional)
PULL DOWN
Trunk Pull
-
Down Motor
ANTENNA
Power Mast Antenna
RSS
Damper Relay (ETC Only)
Fuse
Usage
CONVENC
Trunk Release Relay, Trunk
Release Solenoid, Fuel Door
Release Relay, Fuel Filler Door
Release Solenoid, Door Lock
Relay, Left and RIght Door
Motors, PZM, Door Unlock Relay
BATT
Driver and Passenger Seat Lumbar
Switch (Optional), Driver and
Passenger Seat Belt Comfort
Solenoid, Memory Seat
Module (Optional)
RSS
Road Sensing Suspension (RSS)
Module (ETC Only)
RT PARK
Headlamp Switch, Right Front
Parking Lamp, Right Front and
Rear Sidemarker Lamps, Right
Turn/Stop/Tail Lamps
LT PARK
Left Front and Rear Sidemarker
Lamps, Left Front Parking Lamp,
Left Turn/Stop/Tail Lamps, Right
and Left License Lamps,
Underhood Lamp