Cadillac Fleetwood - 1994 Fuse Box Diagram

Cadillac Fleetwood - 1994 Fuse Box Diagram

The alarm won’t stop if
you try to unlock a door any other way.
How
to
Test
The
Alarm
r
0
From inside the vehicle
roll
down
your
window,
then get out of your
vehicle keeping the
door open.
0
From outside the vehicle
with the
dooropen, lock the vehicle
using
the power door lock or
the Keyless Entry System and close the door.
0
Once the interior lights are
off,
reach in and unlock the
door using the
manual lock. Open the door, the
horn will sound and your headlights
will flash.
If the alarm does not sound when
it should, check to see
if
the horn
works. The horn fuse may be blown. To replace the fuse, see “Fuses and
Circuit Breakers” in the Index.
To
reduce the possibility of theft, always arm the theft deterrent system
when
leaving
your
vehicle.
Your vehicle is equipped with the [email protected]
(Personalized
Automotive Security System) theft deterrent system.
is
a
passive theft deterrent system. This means you don’t have to
do anything
different to arm or disarm the system. It works
when
you
insert or remove
the
key
from the ignition.
uses
a resistor pellet in the
ignition key that matches a decoder in
your
vehicle.
system
senses that someone is
using the wrong
key, it shuts down the vehicle’s starter and fuel systems. For about three
minutes, the
starter won’t
work and fuel won’t
go
to
the engine. If
someone tries to
start your vehicle again or uses another key during this
time, the vehicle will not start. This discourages someone from randomly
trying different keys with different resistor pellets in an attempt to make a
match.
The ignition
key
must be clean and dry before it’s inserted in the ignition
or
the engine may not start. If the engine does not start and and the
“PASS
KEY
FAULT” light comes on, the key
may be dirty or wet.
Turn
the ignition
off.
83
Clean and dry the key.
If
the
starter still won’t work, and the key appears
to
be clean and dry,
wait about three minutes and try the
other
ignition
key.
At this time, you
may also
want to check the (see “Fuses and Circuit
Breakers” in the Index). If the
starter won’t
work
with the
other key,
your
vehicle needs service. If your
vehicle does start,
the
first
ignition key
may
be faulty. See your Cadillac dealer or a locksmith
who
can
service
the
If
you accidentally use a
key
that has a damaged or missing
resistorpellet,
the
starter won’t
work
But
you don’t have to wait three minutes before
trying one of the
other
ignition keys.
See your Cadillac dealer or a locksmith who can service the [email protected]
to have
a
new
key
made.
If you’re ever driving and the “PASS KEY FAULT” light
comes on and
stays on, you
will be able to restart your engine if you turn it
off.
Your
system,
however,
is
not working properly and must be
serviced by your Cadillac dealer. Your vehicle
is not protected by the
system.
If
you lose or damage a [email protected]
ignition
ke
,
see your Cadillac
dealer or a locksmith who can
service PASS-Key
I1 to have a new
key
made.
J
84
A
green arrow on
the
instrument panel will
flash
in the direction
of
the
turn
or
lane
change.
To
signal
a
lane change, just raise or lower the lever
until the
green arrow
starts to flash. Hold it there until you complete your lane change. The
lever
will
return by itself
when
you
release it.
As
you
signal a turn or a lane change, if the arrows
don’t
flash
but just
stay on, a signal
bulb may be burned
out and other drivers won’t see your
turn signal.
If
a bulb is burned
out, replace it to help avoid an accident.
If
the
green
arrows
don’t go on
at all
when
you
signal
a turn, check the fuse (see
Fuses” in the Index) and for
burned-out bulbs.
If you
have
a
trailer towing option with added wiring
for
the trailer lights,
a different turn signal flasher is used.
With
this
flasher installed, the
signal indicator will flash
even
if a turn signal
bulb
is
burned out. Check
the
front and rear
turnsignal
lights
regularly
to make sure they are
working.
Operation
of
Lights
Although your vehicle’s
lighting
system
(headlights,
parking
lights,
fog
lamps,
side marker lights and taillights) meets all
applicable federal
lighting requirements, certain
states and provinces
may
apply
their own
lighting regulations that may require special attention before you operate
these lights.
For example, some jurisdictions
may
require
that you operate your
lower
beam
lights
with
fog
lamps
at all
times, or
that headlights be
turned
on
whenever
you
must
use
your windshield
wipers.
In addition, most
106
Trailer
Hitching
Procedure
Using
A Weight
Distributing (Equalizing) Hitch
(Recommended
for
loaded trailers weighing
3,000
lbs.
to
7,000
lbs.)
Your vehicle is equipped
with
an Electronic Level Control (ELC) feature.
When hooking up a trailer using a weight
distributing
hitch,
always use
the following procedure:
0
0
0
0
0
Place the vehicle on
a
level surface without the trailer hitched.
With
the ignition
off, and all doors closed,
allow
the vehicle to level
automatically.
Disable the Electronic Level Control (ELC) by pulling
fuse
#9
(30
AMP) from the underhood electrical center located on
the passenger side
wheel
housing
in
the engine compartment. Remove
the cover to gain
access.
Attach the trailer to the vehicle. The trailer tongue should weight
12%
of the total loaded trailer weight.
Level the vehicle
with
the load leveling spring bars (equalizers).
Leave the fuse out while
towing
your
trailer.
NOTICE:
Adjusting
an
equalizing
hitch
with
the
Electronic
Level
Control
(ELC)
system
engaged
will
defeat
the
function
of
the
load
equalizing
hitch
and may cause
unsatisfactory
handling.
Once you
havecompleted towing
your trailer, be sure
to
reinstall the
Electronic Level Control (ELC) fuse.
In
Addition
Use
two
friction sway controls if your trailer is
over
5,000
lbs.
.(2270
kg) loaded weight, and/or
is.
over
24'.
long..
0
Use at least one friction sway control if your trailer is over
2,000
lbs.
(908
kg)
loaded weight, and consider using one for trailers under
2,000
lbs.
(908
kg).
206
FUSES
AND
CIRCUIT BREAKERS
The wiring
circuits
in
your
vehicle are protected from short circuits by a
combination of Mini
Fuses,
Circuit Breakers, and
Maxi
Fuses. This
greatly reduces the chance of fires caused. by electrical
problems..
If
you ever have a problem on
the
road and don’t
have a spare fuse, you
can “borrow” one,of
the
correct value. Select a feature
that you can get
along without tha.t
is
the same value you need
--
like the radio or cigarette
lighter
--
and use
its
fuse.
Be
sure to use a fuse
with
the same amperage
rating number on it
(ie.
lOA,
20A,
etc.). Replace it
as
soon
as
you
can.
Instrument
Panel
Fuse
Block
To
gain
access
to the fuse block.
Remove the
instrument panel side
cover.
312
Headlights
The headlight wiring
is protected by a circuit breaker in the light
switch.
An
electrical overload will cause the lights to go on and off, or
in
some
cases to remain
off.
If
this happens, have
your headlight wiring
checked
right away.
Windshield Wipers
The windshield
wiper motor is protected by a circuit breaker and
a
fuse.
If
the motor overheats due to heavy
snow,
etc.,
the wiper
will
stop until
the motor cools. If the overload is
causedby some electrical problem and
not snow,
etc., be sure to get it
fixed.
Power
Windows and Other
Power
Options
Circuit breakers in the fuse panel protect the power
windows and other
power
accessories.
When
the current load is too heavy, the circuit breaker
opens and closes, protecting the circuit
until
the problem is
fixed or goes
away.
316