Toyota Aygo - 2012 Fuse Box Diagram

Toyota Aygo - 2012 Fuse Box Diagram

236
3-6. Other interior features
AYGO_WE_99G80E
Power outlet
The power outlet can be used when
The engine switch is in the “ACC” or “ON” position.
NOTICE
To avoid damaging the power outlet
Close the power outlet lid when the power outlet is not in use.
Foreign objects or liquids that enter the power outlet may cause a short cir-
cuit.
To prevent blown fuse
Do not use an accessory that uses more than 12 V 120 W.
To prevent battery discharge
Do not use the power outlet longer than necessary when the engine is not
running.
The power outlet can be used for 12 V accessories that run on less
than 120 W.
251
4
Maintenance and care
AYGO_WE_99G80E
4-3. Do-it-yourself maintenance
Do-it-yourself service precautions
If you perform maintenance by yourself, be sure to follow the correct
procedures as given in these sections.
Items
Parts and tools
Battery condition
(
P. 266)
• Warm water
• Baking soda
• Grease
• Conventional wrench
(for terminal clamp bolts)
Engine coolant level
(
P. 264)
• “Toyota Super Long Life Coolant”
or a similar high quality ethylene
glycol-based non-silicate, non-
amine, non-nitrite and non-borate
coolant with long-life hybrid
organic acid technology. “Toyota
Super Long Life Coolant” is pre-
mixed with 50% coolant and 50%
deionized water.
• Funnel (used only for adding cool-
ant)
Engine oil level

P. 261)
• “Toyota Genuine Motor Oil” or
equivalent
• Rag or paper towel
• Funnel (used only for adding
engine oil)
Fuses
(
P. 282)
Fuse with same amperage rating
as original
Light bulbs
(
P. 292)
• Bulb with same number and watt-
age rating as original
• Phillips-head screwdriver
• Flathead screwdriver
• Wrench
Radiator and condenser
(
P. 266)
260
4-3. Do-it-yourself maintenance
AYGO_WE_99G80E
Engine compartment
Washer fluid tank (
P. 269)
Engine oil level dipstick
(
P. 261)
Engine oil filler cap
(
P. 262)
Fuse box
(
P. 282)
Battery
(
P. 266)
Engine coolant reservoir
(
P. 264)
Condenser
(
P. 266)
Electric cooling fan
Radiator
(
P. 266)
282
4-3. Do-it-yourself maintenance
AYGO_WE_99G80E
Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have
blown. If this happens, check and replace the fuses as necessary.
Turn the engine switch to the “LOCK” position.
Open the fuse box cover.
Engine compartment
Push the tab in and lift the lid
off.
Instrument panel
If the following procedures seems difficult to perform, consult any
authorized Toyota dealer or repairer, or another duly qualified and
equipped professional.
Remove the meter cover
screws, by using a Phillips-
head screwdriver.
If the steering lock is engaged,
please disengage it. (
P. 127)
283
4-3. Do-it-yourself maintenance
4
Maintenance and care
AYGO_WE_99G80E
Remove the bottom screw
of the tachometer, and lift
and pull up on the tachome-
ter.
Pull the meter cover for-
ward, lift up, and remove
the meter cover.
After a system failure, see “Fuse layout and amperage
ratings” (
P. 285) for details about which fuse to check.
Remove the fuse.
Only type A fuse can be
removed using the pullout
tool.
screw
284
4-3. Do-it-yourself maintenance
AYGO_WE_99G80E
Check if the fuse is blown.
Type A
Normal fuse
Blown fuse
Replace the blown fuse with a
new fuse of an appropriate
amperage rating.
Type B
Normal fuse
Blown fuse
Replace the blown fuse with a
new fuse of an appropriate
amperage rating.
Type C
Normal fuse
Blown fuse
Contact any authorized Toyota
dealer or repairer, or another
duly qualified and equipped
professional.
285
4-3. Do-it-yourself maintenance
4
Maintenance and care
AYGO_WE_99G80E
Fuse layout and amperage ratings
Engine compartment (top side)
Fuse
Ampere
Circuit
1
DRL
5 A
Daytime running lights
2
FOG FR
20 A
Front fog lights
3
H-LP LH
10 A
Left-hand headlights
4
H-LP RH
10 A
Right-hand headlights
5
STA
7.5 A
Multi-mode manual transmission,
multiport fuel injection system/
sequential multiport fuel injection
system
6
EFI NO.2
7.5 A
Multiport fuel injection system/
sequential multiport fuel injection
system, multi-mode manual trans-
mission
7
MET
5 A
Gauges and meters
8
SUB-LP
30 A
DRL, FOG FR fuses
9
ABS NO.2
*
1
25 A
Anti-lock brake system
VSC NO.2
*
2
30 A
Anti-lock brake system and vehicle
stability control system
286
4-3. Do-it-yourself maintenance
AYGO_WE_99G80E
*
1
:
Vehicles without VSC system
*
2
:
Vehicles with VSC system
*
3
:
Replace the fuse with one of the same ampere rating as the original
10
AM2
30 A
Starting system, IG1, IG2, STA
fuses
11
HAZARD
10 A
Turn signal lights, emergency
flashers, gauges and meters
12
H-LP MAIN
20 A
H-LP LH, H-LP RH fuses
13
DOME
15 A
Gauges and meters, interior light,
audio system, tachometer
14
EFI
15 A
Electric cooling fan, multiport fuel
injection system/sequential multi-
port fuel injection system
15
HORN
10 A
Horn
16
SPARE
7.5 A
Spare fuse
17
SPARE
10 A
Spare fuse
18
SPARE
15 A
Spare fuse
19
AMT
50 A
Multi-mode manual transmission
20
RADIATOR
30 A
*
3
Electric cooling fan
40 A
*
3
21
ABS
*
1
40 A
Anti-lock brake system
VSC
*
2
50 A
Anti-lock brake system and vehicle
stability control system
22
EMPS
50 A
Electric power steering system
Fuse
Ampere
Circuit
287
4-3. Do-it-yourself maintenance
4
Maintenance and care
AYGO_WE_99G80E
Engine compartment (back side)
Fuse
Ampere
Circuit
1
ALTERNATOR
120 A
Charging system, EMPS, ABS,
VSC, RADIATOR, AM1, HTR,
PWR, D/L, DEF, TAIL, STOP, OBD,
ECU-B fuses
288
4-3. Do-it-yourself maintenance
AYGO_WE_99G80E
Instrument panel (right side)
Fuse
Ampere
Circuit
1
STOP
10 A
Stop lights, high mounted stoplight,
anti-lock brake system, multi-mode
manual transmission
2
D/L
25 A
Power door lock system, wireless
remote control system
3
DEF
20 A
Rear window defogger
4
TAIL
7.5 A
Daytime running light system, tail
lights, license plate lights, position
lights, headlight beam level control
system, instrument panel lights
5
OBD
7.5 A
On-board diagnosis system
6
ECU-B
7.5 A
Multi-mode manual transmission,
daytime running light system, vehi-
cle stability control system, gauges
and meters, rear fog light
289
4-3. Do-it-yourself maintenance
4
Maintenance and care
AYGO_WE_99G80E
Instrument panel (left side)
Fuse
Ampere
Circuit
1
ECU-IG
7.5 A
Anti-lock brake system, vehicle sta-
bility control system, electric power
steering system, electric cooling fan
2
BACK UP
10 A
Back-up lights, power door lock
system, wireless remote control
system, power windows, rear win-
dow defogger, tachometer, air con-
ditioning system, heater system
3
WIP
20 A
Windshield wiper and washer, rear
window wiper and washer
4
ACC
15 A
Power outlet, audio system
5
IG1
7.5 A
Windshield wiper and washer, rear
window wiper and washer, anti-lock
brake system, electric power steer-
ing system, electric cooling fan,
back-up lights, power door lock
system, wireless remote control
system, power windows, rear win-
dow defogger, tachometer, air con-
ditioning system, heater system
6
IG2
15 A
Multiport fuel injection system/
sequential multiport fuel injection
system, SRS airbag system,
gauges and meters, daytime run-
ning light system, multi-mode man-
ual transmission
290
4-3. Do-it-yourself maintenance
AYGO_WE_99G80E
Instrument panel (back side)
7
A/C
7.5 A
Air conditioning system, power
heater
Fuse
Ampere
Circuit
1
AM1
40 A
ACC, WIP, ECU-IG, BACK UP
fuses
2
PWR
30 A
Power windows
3
HTR
40 A
Heater system, air conditioning
system, A/C fuse
Fuse
Ampere
Circuit
291
4-3. Do-it-yourself maintenance
4
Maintenance and care
AYGO_WE_99G80E
After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (
P. 292)
If the replaced fuse blows again, have the vehicle inspected by any
authorized Toyota dealer or repairer, or another duly qualified and
equipped professional.
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
CAUTION
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
Do not modify the fuses or fuse boxes.
NOTICE
Before replacing fuses
Have the cause of electrical overload determined and repaired by any autho-
rized Toyota dealer or repairer, or another duly qualified and equipped pro-
fessional as soon as possible.
AUDIO SYSTEM
165
1 2 3 4 5 6 (Preset buttons)
These
buttons
are
used
to
preset
and
tune in radio stations.
To preset a station to a button: Tune in
the desired station. (See “TUNE/TRACK”
button).
Push and hold down
the button
until
you
hear
a
beep—this
will
set
the
station to the button. The button number
will appear on the display.
To recall a preset station: Push the button
for the station you want. The button num-
ber and station frequency will appear on
the display.
These
systems
can
store
one
AM
and
three
FM
station
for
each
button.
(The
display will show “AM”, “FM1”, “FM2” or
“FM3” when you push “AM/FM”.) The pre-
set station memory will be canceled out
if the power source is interrupted. (Battery
disconnected or fuse blown.)
(Eject button)
Push this button to eject a compact disc.
After
you
turn
the
engine
switch
to
“LOCK”, you will be able to eject a com-
pact disc but you will not be able to rein-
sert it.
TUNE/TRACK (Tuning/Track up/down)
Radio
Tuning:
Quickly push and release the “
” or “
button.
Each
time
you
push
the
button,
the radio will step up or down to another
frequency. If you hear a beep, you held
the button too long and the radio will go
into the seek mode.
Seeking:
Push and hold the “
” or “
” until you
hear a beep. The radio will begin seeking
up or
down for
a station of
the nearest
frequency and will stop on reception. Each
time you push the button, the stations will
be searched automatically one after anoth-
er.
Compact disc player
By using this button, you can either skip
up/down
to
a
different
track
or
fast
for-
ward/reverse
the
track
you
are
listening
to.
Skip up/down tracks:
Quickly push and release the “
” or “
button. The track number will appear on
the display. If you hear a beep, you held
the
button
too
long,
and
the
player
will
fast forward or reverse a track.
Fast forward/reverse tracks:
Push
and
hold
the
or
until
you hear a beep. While you are holding
the button, the player will fast forward/re-
verse
the
track.
When
you
release
the
button, the player will resume playing.
” (Power)
Push
to
turn
the
audio
system
on
and off. The audio power can be turned
on only once even when the key
is not
in the engine switch. The power, however,
will automatically turn off when 30 minutes
have elapsed.
VOL (Volume)
The volume can be adjusted by pushing
the “
” or “
” button.
AYGO WE 99E37E
11 02.18
188
OTHER EQUIPMENT
Clock
MS19005a
Before adjusting the clock.
Push the “CLOCK” button until you hear
a beep.
To reset the hour: Push the “
” button.
To reset the minutes: Push the “
” but-
ton.
The engine switch must be in the “ACC”
or “ON” position.
If
the
electrical
power
source
has
been
disconnected from the clock, the time dis-
play will automatically be set to 1:00.
When
the
instrument
panel
lights
are
turned on, the brightness of the time in-
dication will be reduced.
Turning the system on and off
Push “
” (Power) to turn the audio sys-
tem on and off. The audio power can be
turned on only once even when the key
is
not
in
the
engine
switch.
The
power,
however, will automatically turn off when
30 minutes have elapsed.
Power outlet
MS19006a
The power outlet is designed as a pow-
er
supply for
car accessories.
To use
the power outlet, open it as shown in
the illustration.
The engine switch must be in the “ACC”
or “ON” position to be used.
NOTICE
z
To
prevent
the
fuse
from
being
blown, do not use more electricity
than
the
total
vehicle
capacity
of
12V/120W.
z
To prevent
the battery
from being
discharged,
do
not
use
the power
outlet
for
longer
than
necessary
when the engine is not running.
z
Close the power outlet lid when the
power outlet is not in use. Inserting
anything other than an appropriate
plug that fits the outlet, or allowing
any liquid to get into the outlet may
cause electrical failure or short cir-
cuits.
z
Do
not
turn
car
accessory
plugs
when
they
are
inserted
into
the
power outlet. Doing so may damage
the power outlet, depending on the
plug shape.
AYGO WE 99E37E
11 02.18
212
STARTING AND DRIVING
Seat belts.
Check that the buckles lock
securely.
Make
sure
the
belts
are
not
worn or frayed.
Instruments
and
controls.
Especially
make sure the service reminder indicators,
instrument lights, and defroster are work-
ing.
Brakes.
Make sure the pedal has enough
clearance.
In the engine compartment
Spare fuses.
Make sure you have spare
fuses. (See “Fuse locations” on page 259
in Section 7
1.)
Coolant level.
Make sure the coolant lev-
el
is
correct.
(See
page
267
in
Section
7
2 for instructions.)
Battery and cables.
All the battery cells
should be filled to the proper
level
with
distilled water. Look for corroded or loose
terminals and a cracked case. Check the
cables for good condition and connections.
Wiring.
Look for damaged, loose, or dis-
connected wires.
Fuel lines.
Check the lines for leaks or
loose connections.
AFTER STARTING THE ENGINE
Exhaust system.
Listen for any leakage.
Have
any
leaks
fixed
immediately.
(See
“Engine exhaust cautions” on page 198 in
Section 2.)
Engine
oil
level.
Stop
the
engine
and
check the dipstick with the vehicle parked
on a level spot. (See page 264 in Section
7
2 for instructions.)
WHILE DRIVING
Instruments.
Make sure the speedometer
and gauges are working.
Brakes.
In a safe place, check that the
brakes do not pull to one side when ap-
plied.
Anything unusual?
Look for loose parts
and leaks. Listen for abnormal noises.
If everything looks O.K., set your mind at
ease and enjoy your trip!
AYGO WE 99E37E
11 02.18
280
DO
IT YOURSELF MAINTENANCE: Electrical components
Battery recharging precautions
During
recharging,
the
battery
is
pro-
ducing hydrogen gas.
Therefore, before recharging:
1
. If recharging with the battery installed
on
the
vehicle,
be
sure
to
turn
the
engine
switch
to
the
“LOCK”
position
and then disconnect the ground cable.
2. Be
sure
the
power
switch
on
the re-
charger
is
off
when
connecting
the
charger cables to the battery and when
disconnecting them.
CAUTION
D
Always charge the battery in an un-
confined
area.
Do
not
charge
the
battery in a garage or closed room
where there is not sufficient ventila-
tion.
D
Only
do
a
slow
charge
(5
A
or
less). Charging at a quicker rate is
dangerous.
The
battery
may
ex-
plode, causing personal injuries.
NOTICE
Never recharge the battery while the
engine
is running.
Also,
be
sure all
accessories are turned off.
Checking and replacing fuses
MS73033
Good
Blown
Type A
MS73034
Good
Blown
Type B
MS73035a
Good
Blown
Type C
AYGO WE 99E37E
11
02.
1
8
DO
IT YOURSELF MAINTENANCE: Electrical components
28
1
MS73028a
If
the
headlights
or
other
electrical
components
do
not
work,
check
the
fuses.
If
any
of
the
fuses
are
blown,
they must be replaced.
See “Fuse locations” on page 259 in Sec-
tion 7
−1
for locations of the fuses.
Turn the engine switch and inoperative
component off. Pull the suspected fuse
straight out and check it.
Determine which fuse may be causing the
problem. See page 300 in Section 8 for
the functions controlled by each circuit.
Type A fuses can be pulled out using the
pull
out tool. The location of the pull
out
tool is shown in the illustration.
If
you are
not
sure
whether
a
fuse has
blown,
try
replacing
the
suspected
fuse
with one that you know is good.
If the fuse has blown, push a new fuse
into the clip.
If
you
do
not
have
a
spare
fuse,
in an
emergency you can pull out the “DOME”
fuse, which may be dispensable for nor-
mal
driving,
and
use
it
if
its
amperage
rating is the same.
If you cannot use one of the same amper-
age, use one that is lower, but as close
to the rating as possible. If the amperage
is
lower
than
that
specified,
the
fuse
might
blow
out
again
but
this
does
not
indicate anything wrong. Be sure to get a
correct fuse as soon as possible and re-
turn the substitute to its original clip.
It
is
a
good
idea
to
purchase
a
set
of
spare
fuses
and
keep
them
in
your
ve-
hicle for emergencies.
If
the
new
fuse
immediately
blows
out,
there is a problem with the electrical sys-
tem. Have any authorized Toyota dealer or
repairer,
or
another
duly
qualified
and
equipped professional, correct it as soon
as possible.
CAUTION
Never use a fuse with a higher am-
perage rating, or any other object, in
place of a fuse. This may cause ex-
tensive damage and possibly a fire.
AYGO WE 99E37E
11
02.
1
8
300
SPECIFICATIONS
Fuses
MS81007a
Engine room R/B (top side)
MS81012a
Engine room R/B (back side)
MS81008a
Instrument panel J/B (left side)
MS81009a
Instrument panel J/B (right side)
MS81010a
Instrument panel J/B (back side)
AYGO WE 99E37E
11 02.18
SPECIFICATIONS
301
Fuses (type A)
1. H
LP
RH
(HI)
10
A
(with
daytime
running
light
system):
Right
hand
headlights
2. H
LP LH (HI) 10 A (with daytime run-
ning
light
system):
Left
hand
head-
lights, gauges and meters
3. H
LP
RH
(LO)
10
A
(with
daytime
running
light
system):
Right
hand
headlights
4. H
LP
LH
(LO)
10
A
(with
daytime
running
light
system):
Left
hand
headlights, gauges and meters
5. DIMMER 20 A (with daytime running
light system):
“H
LP LH (HI)”, “H
LP
RH(HI)”,
“H
LP
LH
(LO)”,
“H
LP
RH
(LO)” fuses, daytime running light sys-
tem
H
LP LH 10 A (without daytime run-
ning
light
system):
Left
hand
head-
lights
6. ABS NO.2 25 A (without vehicle sta-
bility control system):
Anti
lock brake
systemand vehicle stability control sys-
tem
VSC NO.2 30 A (with vehicle stability
control system):
Anti
lock brake sys-
tem and vehicle stability control system
7. AM2
30
A:
Starting
system,
“IG1”,
“IG2”, “STA” fuses
8. HAZARD
10
A:
Turn
signal
lights,
emergency flashers, gauges and meter-
s
9. H
LP RH 10 A (without daytime run-
ning light system):
Right
hand head-
lights
10. DOME 15 A:
Gauges and meters, inte-
rior light, audio system, tachometer
11. EFI
15 A:
Electric
cooling fan, multi-
port
fuel
injection
system/sequential
multiport fuel injection system
12. HORN 10 A:
Horn
13. SPARE 7.5 A:
Spare fuse
14. SPARE 10 A:
Spare fuse
15. SPARE 15 A:
Spare fuse
16. STA 7.5 A:
Multi
mode manual trans-
mission, multiport fuel injection system/
sequential
multiport
fuel
injection
system
17. EFI NO.2 7.5 A:
Multiport fuel injection
system/sequential
multiport
fuel
injec-
tion system, multi
mode manual trans-
mission
18. STOP 10 A:
Stop lights, high mounted
stoplight, anti
lock brake system, mul-
ti
mode manual transmission
19. D/L
25
A:
Power
door
lock
system,
wireless remote control system
20. DEF 20 A:
Rear window defogger
21. TAIL 7.5 A:
Daytime running light sys-
tem,
tail
lights,
license
plate
lights,
position
lights,
headlight
beam
level
control system, instrument panel lights
22. OBD 7.5 A:
On
board diagnosis sys-
tem
23. ECU
B
7.5
A:
Multi
mode
manual
transmission, daytime running light sys-
tem,
vehicle
stability
control
system,
gauges and meters, rear fog light
24. ECU
IG 7.5 A:
Anti
lock brake system,
vehicle stability control system, electric
power steering system, electric cooling
fan
25. BACK UP 10 A:
Back
up lights, power
door lock system, wireless remote con-
trol system, power windows, rear win-
dow defogger, tachometer, air condition-
ing system, heater system
26. WIP 20 A:
Windshield wiper and wash-
er, rear window wiper and washer
27. ACC 15 A:
Power outlet, audio system
AYGO WE 99E37E
11 02.18
302
SPECIFICATIONS
28. IG1 7.5 A:
Windshield wiper and wash-
er,
rear
window
wiper
and
washer,
anti
lock brake system, electric power
steering
system,
electric
cooling
fan,
back
up
lights,
power
door
lock
sys-
tem,
wireless
remote
control
system,
power windows, rear window defogger,
tachometer,
air
conditioning
system,
heater system
29. IG2 15 A:
Multiport fuel injection sys-
tem/sequential
multiport
fuel
injection
system,
SRS
airbag
system,
gauges
and meters, daytime running light sys-
tem, multi
mode manual transmission
30. A/C
7.5
A:
Air
conditioning
system,
power heater
Fuses (type B)
31. AM1
40
A:
“ACC”,
“WIP”,
“ECU
IG”,
“BACK UP” fuses
32. PWR 30 A:
Power windows
33. HTR 40 A:
Heater system, air condi-
tioning system, “A/C” fuse
34. AMT 50 A:
Multi
mode manual trans-
mission
35. RADIATOR
30
A
or
40
A
:
Electric
cooling fan
∗:
Replace the fuse with one of the same
ampere rating as the original.
36. ABS NO.1 40 A (without vehicle sta-
bility control system):
Anti
lock brake
system
and
vehicle
stability
control
system
VSC NO.1 50 A (with vehicle stability
control system):
Anti
lock brake sys-
tem and vehicle stability control system
37. EMPS
50
A:
Electric
power
steering
system
Fuse (type C)
38. ALTERNATOR
120
A:
Charging
sys-
tem, “EPS”, “ABS (without vehicle sta-
bility control system)”, “VSC (with ve-
hicle
stability
control
system)”,
“RADIATOR”,
“AM1”,
“HTR”,
“PWR”,
“D/L”,
“DEF”,
“TAIL”,
“STOP”,
“OBD”,
“ECU
B” fuses
AYGO WE 99E37E
11 02.18