Toyota Camry Hybrid - 2016 Fuse Box Diagram

Toyota Camry Hybrid - 2016 Fuse Box Diagram

392
7-3. Do-it-yourself maintenance
Do-it-yourself service precautions
If you perform maintenance by yourself, be sure to follow the
correct procedure as given in these sections.
Items
Parts and tools
12-volt
battery
condition
(
P. 404)
• Grease
Conventional wrench (for terminal clamp bolts)
Brake fluid level
(
P. 402)
FMVSS No.116 DOT 3 or SAE J1703 brake fluid
Rag or paper towel
Funnel (used only for adding brake fluid)
Engine/power
control unit cool-
ant level
(
P. 400)
• “Toyota Super Long Life Coolant” or a similar high
quality ethylene glycol-based non-silicate, non-
amine, non-nitrite and non-borate coolant with long-
life hybrid organic acid technology
U.S.A.:
“Toyota Super Long Life Coolant” is pre-mixed with
50% coolant and 50% deionized water.
Canada:
“Toyota Super Long Life Coolant” is pre-mixed with
55% coolant and 45% deionized water.
Funnel (used only for adding coolant)
Engine oil level
(
P. 397)
“Toyota Genuine Motor Oil” or equivalent
Rag or paper towel
Funnel (used only for adding engine oil)
Fuses (
P. 427)
Fuse with same amperage rating as original
Light bulbs
(
P. 430)
Bulb with same number and wattage rating as origi-
nal
Phillips-head screwdriver
Flathead screwdriver
• Wrench
Radiator/con-
denser (
P. 401)
Tire
inflation
pressure
(
P. 418)
Tire pressure gauge
Compressed air source
Washer fluid
(
P. 403)
Water or washer fluid containing antifreeze (for win-
ter use)
Funnel (used only for adding water or washer fluid)
396
7-3. Do-it-yourself maintenance
Engine compartment
Fuse boxes
(
P. 427)
Engine oil filler cap(
P. 398)
Engine oil level dipstick
(
P. 397)
Brake fluid reservoir
(
P. 402)
Engine coolant radiator
(
P. 400)
Power control unit coolant
radiator
(
P. 400)
Condenser
(
P. 401)
Electric cooling fans
Engine coolant reservoir
(
P. 400)
Washer fluid tank
(
P. 403)
Power control unit
coolant reservoir
(
P. 400)
1
2
3
4
5
6
7
8
9
10
11
427
7-3. Do-it-yourself maintenance
7
Maintenance and care
Turn the power switch off.
Open the fuse box cover.
Checking and replacing fuses
If any of the electrical components do not operate, a fuse may
have blown. If this happens, check and replace the fuses as nec-
essary.
1
2
X
Engine compartment (type A)
X
Engine compartment (type B)
Push the tabs in and lift the lid off.
Push the tabs in and lift the lid
off.
X
Under the driver’s side instru-
ment panel
Remove the lid.
428
7-3. Do-it-yourself maintenance
Remove the fuse with the pull-
out tool.
Only type A fuses can be removed
using the pullout tool.
Check if the fuse is blown.
Normal fuse
Blown fuse
Type A and B:
Replace the blown fuse with a new fuse of an appropriate amperage rat-
ing. The amperage rating can be found on the fuse box lid.
Type C:
Contact your Toyota dealer.
3
4
X
Type A
X
Type B
X
Type C
1
2
429
7-3. Do-it-yourself maintenance
7
Maintenance and care
After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb may
need replacement. (
P. 430)
If the replaced fuse blows again, have the vehicle inspected by your Toyota
dealer.
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
When replacing light bulbs
Toyota recommends that you use genuine Toyota products designed for this
vehicle. Because certain bulbs are connected to circuits designed to prevent
overload, non-genuine parts or parts not designed for this vehicle may be
unusable.
WARNING
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
Do not modify the fuses or fuse boxes.
NOTICE
Before replacing fuses
Have the cause of electrical overload determined and repaired by your
Toyota dealer as soon as possible.
484
8-2. Steps to take in an emergency
One of the following may be the cause of the problem:
The electronic key may not be functioning properly. (
P. 488)
There may not be sufficient fuel in the vehicle’s tank.
Refuel the vehicle.
There may be a malfunction in the immobilizer system.
(
P. 78)
There may be a malfunction in the steering lock system.
The hybrid system may be malfunctioning due to an electrical prob-
lem such as an open circuit or a blown fuse. However, depending
on the type of malfunction, an interim measure is available to start
the hybrid system. (
P. 485)
One of the following may be the cause of the problem:
The 12-volt battery may be discharged. (
P. 490)
The 12-volt battery terminal connections may be loose or corroded.
(
P. 404)
If the hybrid system will not start
Reasons for the hybrid system not starting vary depending on
the situation. Check the following and perform the appropriate
procedure:
The hybrid system will not start even though the correct starting
procedure is being followed. (
P. 161)
The interior lights and headlights are dim, or the horn does not
sound or sounds at a low volume.
490
8-2. Steps to take in an emergency
If you have a set of jumper (or booster) cables and a second vehicle
with a 12-volt battery, you can jump start your vehicle by following the
steps below.
Vehicles with an alarm, confirm
that the electronic key is being
carried.
When connecting the jumper (or
booster) cables, depending on the
situation, the alarm may activate
and doors locked. (
P. 81)
Open the hood and remove the
fuse box cover.
Push the tabs in and lift the lid off.
Open the exclusive jump start-
ing terminal cover.
Push the tab in and open the cover.
If the vehicle 12-volt battery is discharged
The following procedures may be used to start the hybrid sys-
tem if the vehicle’s 12-volt battery is discharged.
You can also call your Toyota dealer or a qualified repair shop.
1
2
3
492
8-2. Steps to take in an emergency
Start the engine of the second vehicle. Increase the engine speed
slightly and maintain at that level for approximately 5 minutes to
recharge the 12-volt battery of your vehicle.
Open and close any of the doors of your vehicle with the power
switch off.
Maintain the engine speed of the second vehicle and turn the power
switch to ON mode, then start the vehicle's engine.
Make sure the “READY” indicator comes on. If the indicator does
not come on, contact your Toyota dealer.
Once the hybrid system has started, remove the jumper cables in
the exact reverse order from which they were connected.
Close the exclusive jump starting terminal cover, and reinstall the
fuse box cover to its original position.
Once the hybrid system starts, have the vehicle inspected at your
Toyota dealer as soon as possible.
5
6
7
8
9
10