Polaris Ness Signature Series Victory Vision - 2012 Fuse Box Diagram

Polaris Ness Signature Series Victory Vision - 2012 Fuse Box Diagram

31
Instruments, Features and Controls
Engine Starter Switch
The starter switch is located on the right handlebar. Use the
starter switch to start the engine, turn the headlights on and
operate in reverse (if equipped). The switch will operate only
when the engine stop/run switch is in the RUN position and
the transmission is in neutral (or the clutch is disengaged).
The reverse lever (if equipped) must also be disengaged.
Tip:
If the reverse system fuse has blown, the starter switch will not
function even if the reverse lever is disengaged. Replace the
fuse. See page 89.
Read the engine starting procedures before starting the
engine. See page 49.
Press the right side of the starter switch to engage the
starter motor.
Tap the starter switch to turn the headlight on without start-
ing the engine.
See page 55 for reverse operation.
Engine Stop/Run Switch
The engine stop/run switch is located on the right handlebar.
This switch completes or interrupts the ignition, starter and
fuel pump circuits. Use the engine stop/run switch to turn
the engine off quickly. Turn the key off after the engine
stops.
Press the bottom of the switch (RUN) to complete the cir-
cuits and allow the engine to start and run.
Press the top of the switch (STOP) to interrupt the cir-
cuits and stop the engine. The engine should not start or
run when the switch is in the STOP position.
Engage Starter
Run
Stop
37
Instruments, Features and Controls
Radio/Audio Systems
Refer to the Audio System section of this
manual (beginning on page 111) for radio
and accessory audio systems operation.
Tool Kit
The tool kit can be used to perform most
basic maintenance items. Tools provided in
the tool kit include:
1.
4 mm Ball Drive Allen Wrench
2.
4 mm / 6 mm Open End Wrench
3.
6 mm Ball Drive Allen Wrench
4.
8 mm / 10 mm Open End Wrench
5.
Combination Phillips / Slot Screw
Driver
6.
Rear Shock Absorber / Tire Pressure
Gauge
7.
Fuse Puller
Radio Panel
1
2
3
4
5
6
7
81
Maintenance
Battery Installation
WARNING!
Improperly connecting or disconnecting battery
cables can result in an explosion and cause serious injury or
death. When removing the battery, always disconnect the
negative (black) cable first. When reinstalling the battery,
always connect the negative (black) cable last.
1.
Ensure the front battery box tabs are engaged with
the inner box slots. Replace any damaged or miss-
ing foam pads. Slide the battery into the battery box
with terminals forward.
2.
Tip the front battery box toward the inner box and
install the top bolt. Torque to specification.
3.
Install the positive (+) battery cable first. Torque
the bolt to specification. Install the red protective
boot over the terminal.
4.
Install the negative (-) cable last. Torque the bolt to specification.
5.
Reinstall all remaining components.
Battery Charging
Tip:
If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance
charger should be connected to the battery. A fused maintenance charger connection is provided.
The connector is designed for use with the VICTORY accessory maintenance charger available at
your authorized VICTORY dealer.
1.
Following the charger manufacturer’s instructions, use a battery charger designed for use
with 12-volt batteries. The charger should have a maximum charging rate of 1.8 amps.
Charge the battery for approximately 10 hours at a rate of 1.8 amps. If you use a taper or
trickle charger, it will take longer to charge the battery.
2.
After charging the battery, allow the battery to sit 1-2 hours before checking the state of
charge with a DC volt meter. The charge should be a minimum of 12.5 DC volts. Repeat
the charging cycle if the charge is less than 12.5 DC volts. Replace the battery if it fails
to reach 12.5 volts after the second charge.
Tab Slots
Tabs
Forward
85 in-lbs (10 Nm)
36 in-lbs (4 Nm)
+
-
83
Maintenance
Seat Removal / Installation
1.
Open the glove compartment door and the fuel
door.
2.
Lift the console trim panel straight upward at each
corner to remove it. Do not tip the panel rearward.
3.
Remove the two seat bolts.
Tool:
4 mm Allen wrench
4.
Unplug the seat heater power connector (if
equipped). Lift the front of the seat upward and
pull forward to disengage the tab at the rear of the
seat.
5.
To install, reverse the above process, being sure to
engage the tab at the back of the seat.
6.
Tighten the seat bolts.
Torque:
36 in-lbs (4 Nm)
Windshield Trim Panel Removal
Remove the windshield trim panel to access fuse
boxes, the manual windshield adjustment mechanism,
the headlamp adjustment knob and the front turn signal
bulbs.
1.
Lift each panel end upward to release the ends.
2.
Carefully slide the panel slightly toward the wind-
shield to disengage the lower tabs. Remove the
panel.
3.
Unplug the antenna.
4.
Reverse all steps to reinstall the trim panel.
Seat Bolts
36 in-lbs (4 Nm)
89
Maintenance
Fuse Boxes
Remove the windshield trim panel to access the fuses, auto-reset circuit breakers and relays.
See page 83. Use the fuse puller provided in the tool kit to remove a fuse.
Fuse Replacement
1.
Remove the windshield trim panel. See page 83.
2.
Push the center of the dart upward to remove a fuse box cover panel.
3.
Pull the tab to release a fuse box cover.
Tip:
The reverse system fuse is located on the left rear side of the motorcycle, under the seat
.
NOTICE:
Always use the recommended fuse to prevent electrical system damage. Refer to the label
on the fuse box cover.
Left Fuse Box
Right Fuse Box
Left Fuse Box
Right Fuse Box
Tab
Dart
Reverse System
25 amp mini fuse
(if equipped)
ABS Fuses (if equipped)
93
Maintenance
Troubleshooting
Shifting Difficulties or Hard to Find Neutral
Battery Charging Rate Low or Battery Discharges
Brake Noise / Poor Brake Performance
Tip:
Contact a VICTORY dealer if brake performance does not return after these inspections.
Anti-Lock Brake Light Remains Illuminated or Illuminates Intermittently
Possible Cause
Possible Remedy/Action
Shift Linkage Bushings Dry Or Worn
Lubricate shift linkage.
Engine Oil Level Incorrect Or Wrong Type
Inspect level and quality of oil. See page 40.
Hydraulic Clutch Fluid Contaminated
Flush hydraulic clutch fluid (see dealer).
Air In Hydraulic Clutch System
Bleed system (see dealer).
Clutch Slave Cylinder Bracket Loose
Inspect / tighten loose parts.
Hydraulic Clutch Fluid Leak
Inspect system for leaks (see dealer).
Clutch Damage
Replace clutch.
Possible Cause
Possible Remedy/Action
Loose/Corroded Charging Circuit
Connection
Check/clean battery cable connections. Check/clean
charging circuit connections. See dealer.
Accessory Load Exceeds Charge Rate
Use ACC position and limit accessory operation when
engine is off.
Improperly Wired Accessory (Current Draw)
See dealer to check charging system output and cur-
rent draw.
Battery discharges when motorcycle not in
use.
See dealer to check key OFF current draw.
Possible Cause
Possible Remedy/Action
Dust / Dirt On Brake Disc(s)
Clean disc. See page 76.
Worn Pads Or Disc / Brake Disc Damage
Inspect pads. See pages 43 and 76.
Brake Fluid Level Low Or Fluid Contaminated
Inspect fluid level / fluid. See pages 41 and 42.
Possible Cause
Possible Remedy/Action
Blown fuse
Check the fuses. See page 89.
Loose or damaged pulse ring
Inspect pulse ring for looseness or chipped teeth.
Debris lodged in components
Inspect wheel speed sensor and pulse ring for debris.
Damage caused by debris
Inspect wheel speed sensor for cracked housing.
Damaged components
See service manual or authorized dealer.
110
Specifications
All Vision Models
Wheels And Tires
Front Wheel Type / Size
Cast or Billet 18 x 3.0 inch
Front Tire Type / Size
DUNLOP Elite 3 - 130/70R18 63H
Radial
Rear Wheel Type / Size
Cast or Billet 16 x 5.0 inch
Rear Tire Type / Size
DUNLOP Elite 3 - 180/60R16 M/C 80H
Radial
Electrical
Alternator
48 Amp Maximum Output
Battery
12 Volt / 18 Amp Hour / 310 CCA / Yuasa YTX20HL
Lights
Headlamp (High / Low)
H4 55/60W
Driving Lamp (Standard)
HS1 35W
Driving Lamp (HID)
D1R 35W
Turn / Tail / Brake Lamp
3157 27/ 7W
License Plate Lamp
W5W 5W
Trunk Lamps (Running Lights)
W5W 5W
Courtesy Lamp (trunk, if equipped)
6411 10W
Fuses
/ Circuit Breakers
Left Fuse Box
Ignition
10A Breaker
Headlight
20A Breaker
Gauges
5A
Radio
25A
Secondary Lights
20A
Horn
20A
Turn Signal / Brake
20A
Right Fuse Box
Engine
15A Breaker
Windshield (Electric)
20A
Fuel Pump / Ignition Coil
15A
Anti-Lock Brake System
30A (2)