Polaris Cross Country - 2011 Fuse Box Diagram

Polaris Cross Country - 2011 Fuse Box Diagram

17
Identification
Left Side View
1.
Spark Plugs
2.
Front Brake Caliper
3.
Oil Cooler
4.
Battery
5.
Gear Shift Pedal
6.
Operator Footrest
7.
Sidestand
8.
Oil Drain Plug
9.
Oil Filter
10. Passenger Footpeg
11. Rear Brake Caliper
12. Evaporative Emissions
Canister
13. Diagnostic Connector
(under cover)
Right Side View
1.
Exhaust Mufflers
2.
Drive Belt Guard
3.
Drive Sprocket (under cover)
4.
Engine Oil Fill Cap / Dipstick
5.
Rear Brake Fluid Reservoir
6.
Rear Brake Pedal
7.
Air Filter
8.
Headlamp
9.
Mirror
10. Fuel Tank
11. Access Cover
12. Fuse Box (under cover)
13. Accessory Fuse (under
cover)
14. Rear Shock Air Fitting (under
cover)
15. Radio Antenna (if equipped)
16. License Plate Bracket
1
2
5
6
7
8
9
10
11
3
12
4
13
2
3
4
6
12
14
1
8
7
5
16
15
9
10
13
11
18
Identification
Top View
1.
Windshield
2.
Clutch Lever
3.
Fuel Filler Cap
4.
Operator Seat
5.
Passenger Seat
6.
Saddlebag Latch
7.
Turn Signals
8.
Tail Lamps
9.
Front Brake Lever
10. Front Brake Fluid Reservoir
11. Radio Fuse (inside fairing)
Console (CROSS COUNTRY)
1.
Speakers
2.
Mode Switch
3.
Fuel Gauge
4.
Speedometer
5.
Indicator Lamp Display
6.
Multi-Function Display
7.
Tachometer
8.
Volt Meter
9.
Left Handlebar Switches
10. Audio Control Switches
11. +12-Volt Accessory Outlet
12. Radio Display
13. Heated Grip Switch (if equipped)
14. Cruise Control Switches (if equipped)
15. Right Handlebar Switches
Console (CROSS ROADS)
1.
Clutch Lever
2.
Mirror
3.
Speedometer
4.
Indicator Light Panel
5.
Tachometer (if equipped)
6.
Front Brake Fluid Reservoir
7.
Front Brake Lever
8.
Throttle Control Grip
9.
Switches
10.
Throttle Cables
11.
Fuel Cap
12. Cruise Control Switches (if
equipped)
1
2
4
5
9
10
3
6
7
8
11
1
3
4
5
6
7
8
9
1
10
15
14
2
12
11
13
3
5
1
9
11
4
10
9
7
8
2
6
12
31
Instruments, Features and Controls
Right Handlebar Switches
Engine Stop/Run Switch
The engine stop/run switch is located on the right handle-
bar. This switch completes or interrupts the ignition,
starter and fuel pump circuits. Use the engine stop/run
switch to turn the engine off quickly. Turn the key off
after the engine stops.
Press the bottom of the switch (RUN) to complete the
circuits and allow the engine to start and run.
Press the top of the switch (STOP) to interrupt the cir-
cuits and stop the engine. The engine should not start or
run when the switch is in the STOP position.
Cruise Control Switches (if equipped)
Refer to the Cruise Control section of this manual (begin-
ning on page 49) for cruise control operation.
Engine Starter Switch
The starter switch is located on the right handlebar. Use the
starter switch to start the engine and operate in reverse (if
equipped). The switch will operate only when the engine
stop/run switch is in the RUN position and the transmis-
sion is in neutral (or the clutch is disengaged). The reverse
lever (if equipped) must also be disengaged.
Tip:
If the reverse system fuse has blown, the starter switch will
not function even if the reverse lever is disengaged. Replace
the fuse. See page 80.
Read the engine starting procedures before starting the
engine. See page 46.
Press the right side of the starter switch to engage the
starter motor.
See page 52 for reverse operation.
Run
Stop
Cruise Control Switches
Starter Switch
35
Instruments, Features and Controls
Saddlebag Lock
Use the ignition key to lock and unlock the saddle-
bag doors. The doors should be locked before
riding.
To lock a door, place the key in the lock and turn it
counter-clockwise. To unlock a door, turn the key
clockwise.
After unlocking a door, press the door lock to
release the latch and open the door.
Refer to the Gross Vehicle Weight Rating informa-
tion beginning on page 14 for loading information.
Fuel Cap
Use the ignition key to lock and unlock the fuel cap.
Always lock the fuel cap before riding. An open
fuel cap could contact the handlebar.
To open the fuel cap, lift the lock cover. Place the
key in the lock and turn it clockwise.
To secure the fuel cap, push the cap down to engage
the latch. Turn the key counter-clockwise to lock
the cap.
Tool Kit
The tool kit can be used to perform most basic
maintenance items. Tools provided in the tool kit
include:
1.
4 mm Ball Drive Allen Wrench
2.
5 mm Ball Drive Allen Wrench
3.
6 mm Ball Drive Allen Wrench
4.
4 mm / 6 mm Open End Wrench
5.
8 mm / 10 mm Open End Wrench
6.
Combination Phillips / Slot Screw Driver
7.
Rear Shock Absorber / Tire Pressure Gauge
8.
Fuse Puller
Lock
Unlock
1
4
3
5
6
7
8
2
76
Maintenance
Battery Installation
WARNING!
Improperly connecting or disconnecting battery cables can result in an explosion and
cause serious injury or death. When removing the battery, always disconnect the negative (black) cable
first. When reinstalling the battery, always connect the negative (black) cable last.
1.
Place the battery in the battery compartment
with terminals forward.
2.
Reinstall the battery hold-down strap.
3.
Install the positive (+) cable first.
Torque:
36 in-lbs (4 Nm)
4.
Install the red protective boot over the terminal.
5.
Install the negative (-) cable last.
Torque:
36 in-lbs (4 Nm)
6.
Reinstall the front chin fairing. Tighten all four
screws.
Torque:
36 in-lbs (4 Nm)
Battery Charging
Tip:
If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance
charger should be connected to the battery. A fused maintenance charger connection is provided.
The connector is designed for use with the VICTORY accessory maintenance charger available at
your authorized VICTORY dealer.
1.
Following the charger manufacturer’s instructions, use a battery charger designed for use
with 12-volt batteries. The charger should have a maximum charging rate of 1.8 amps.
Charge the battery for approximately 10 hours at a rate of 1.8 amps. If you use a taper or
trickle charger, it will take longer to charge the battery.
2.
After charging the battery, allow the battery to sit 1-2 hours before checking the state of
charge with a DC volt meter. The charge should be a minimum of 12.5 DC volts. Repeat
the charging cycle if the charge is less than 12.5 DC volts. Replace the battery if it fails
to reach 12.5 volts after the second charge.
Ignition Switch / Lock Lubrication
Periodically lubricate the ignition switch, saddle bag locks and fuel cap lock. We recommend
the use of VICTORY Multi-Purpose Lubricant.
1.
Spray lubricant directly into the ignition switch and into each lock cylinder for 1-2 sec-
onds.
2.
Insert each key into its lock and turn it to all positions to distribute the lubricant.
3.
Wipe away any excess lubricant.
36 in-lbs (4 Nm)
Step 3
(
+
)
Step 5
(
-
)
77
Maintenance
Sidestand Lubrication
Periodically lubricate the sidestand pivot and
the ends of the spring. See page 43 for sidestand
inspections.
Fastener Inspection
1.
Inspect the entire motorcycle chassis and
engine for loose, damaged or missing fas-
teners. Tighten loose fasteners to the proper torque.
Tip:
Refer to the specifications section of this manual or the service manual for fastener torque values,
or see your VICTORY dealer.
2.
Always replace stripped, damaged or broken fasteners before riding. Use genuine VIC-
TORY fasteners of equal size and strength.
Side Covers
Remove the left side cover to access the electronic con-
trol module, diagnostic connector and chassis-to-engine
harness connector.
Remove the right side cover to access the fuses, rear
suspension air fitting, clutch cable adjuster, purge valve
and flasher unit.
Remove both side covers to access the seat screws.
1.
Pull outward at each corner of the side cover to dis-
engage the three darts.
2.
Remove the side cover from the motorcycle.
3.
To reinstall the side cover, make sure each rubber
grommet is properly positioned. Align each dart
with the appropriate grommet and press inward
firmly to secure each dart.
Lubricate
Grommets
80
Maintenance
Fuse Replacement
NOTICE:
Use fuses with the recommended amperage to avoid damage to the electrical system.
Tip:
Use the fuse puller provided in the tool kit to remove a fuse.
1.
Remove the right side cover.
2.
Lift the release tab and slide the fuse box
upward to remove it from the bracket.
Release the tabs on each side of the fuse
box cover and remove the cover.
Tip:
The reverse fuse (if equipped) is located on the
debris flap at the front of the rear tire.
3.
Remove the damaged fuse and seat the
new fuse firmly in its place.
4.
Reinstall the fuse box cover with the dou-
ble cut-out to the left (with print readable
from right side of motorcycle).
5.
Reinstall the fuse box and the side cover.
Fuse Recommendations
Fuse Application
Fuse Size
Engine
15 amp
Fuel Pump/Ignition Coil
15 amp
Lights
20 amp
Turn Signals/Horn
10 amp
Ignition
10 amp
Chassis
20 amp
Accessory
(under left side cover)
20 amp
CROSS COUNTRY ONLY
Radio
(in fairing behind headlight)
25 amp
Fuse Box Label
Fuse Box
Accessory
Fuse
(if equipped)
98
Specifications
CROSS ROADS / CROSS COUNTRY
Chassis
Front Suspension Type / Travel
Telescopic Fork / 5.1 in. (13 cm)
Front Fork Tube Diameter
43 mm
Rear Suspension Type / Travel
Single Monotube Air Adjustable Shock: 4.7 in. (12 cm)
Swingarm
Cast Aluminum with Constant Rate Linkage
Front Brakes
Dual 300 x 5 mm / Floating Rotor / 4 Piston Calipers
Rear Brakes
Single 300 x 7 mm / Floating Rotor / 2 Piston Caliper
Total Storage Volume
21.3 gallons (80.6 liters)
Drive System
Final Drive Type
Carbon Fiber Reinforced Belt
Transmission Type
6 Speed Constant Mesh with True Overdrive
Primary Drive Type (Reduction Ratio)
Gear Drive with Torque Compensator (1.49:1)
Drive System
Gear Shift Pattern
1 Down 5 Up
Internal Gear Ratios
1st
3.13:1
2nd
2.02:1
3rd
1.50:1
4th
1.20:1
5th
1:1
6th (Overdrive)
.87:1
Final Drive Ratio
2.12:1
Clutch Type
Wet, Multi Plate, Diaphragm Spring
Wheels And Tires
Front Wheel Type / Size
Cast or Billet 18 x 3.0 inch
Front Tire Type / Size
DUNLOP Elite 3 - 130/70R18 63H
Radial
Rear Wheel Type / Size
Cast or Billet 16 x 5.0 inch
Rear Tire Type / Size
DUNLOP Elite 3 - 180/60R16 M/C 80H
Radial
Electrical
Alternator
48 Amp Maximum Output
Battery
12 Volt / 18 Amp Hour / 310 CCA / Yuasa YTX20HL
Lights
Headlamp (High / Low)
High H11 / Low H11
HID Headlamp (High / Low)
High H11 / Low D1SR
Turn Signal Lamp
Non-Serviceable LED
Tail / Brake / License Plate Lamp
Non-Serviceable LED
Fuses
/ Circuit Breakers
Engine
15A
Fuel Pump/Ignition Coil
15A
Lights
20A
Turn Signals/Horn
10A
Ignition
10A
Chassis
20A
Accessory
20A
Radio
25A (CROSS COUNTRY)