Polaris Victory Vision - 2010 Fuse Box Diagram

Polaris Victory Vision - 2010 Fuse Box Diagram

71
Controls
Instruments/Features/Controls
Engine Starter Switch
The starter switch is located on the right handlebar. Use the starter
switch to start the engine, turn the headlights on and operate in
reverse (if equipped). The switch will operate only when the engine
stop/run switch is in the RUN position and the transmission is in
neutral (or the clutch is disengaged). The reverse lever (if equipped)
must also be disengaged.
Tip:
If the reverse system fuse has blown, the starter switch will not func-
tion even if the reverse lever is disengaged. Replace the fuse. See
page 215.
Read the engine starting procedures before starting the engine. See
page 114.
Press the right side of the starter switch to engage the starter
motor.
Tap the starter switch to turn the headlight on without starting the engine.
See page 129 for reverse operation.
Engage Starter
9922441.book
Page 71
Monday, May 11, 2009
1:16 PM
86
Controls
Instruments/Features/Controls
Tool Kit
The tool kit can be used to perform most basic
maintenance items. Tools provided in the tool kit
include:
1.
4 mm Ball Drive Allen Wrench
2.
4 mm / 6 mm Open End Wrench
3.
6 mm Ball Drive Allen Wrench
4.
8 mm / 10 mm Open End Wrench
5.
Combination Phillips / Slot Screw Driver
6.
Rear Shock Absorber / Tire Pressure Gauge
7.
Fuse Puller
1
2
3
4
5
6
7
9922441.book
Page 86
Monday, May 11, 2009
1:16 PM
199
Maintenance
Maintenance
Battery Charging
Tip:
If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance
charger should be connected to the battery. A fused maintenance charger connection is provided.
The connector is designed for use with the VICTORY accessory maintenance charger available at
your authorized VICTORY dealer.
1.
Following the charger manufacturer’s instructions, use a battery charger designed for use
with 12-volt batteries. The charger should have a maximum charging rate of 1.8 amps.
Charge the battery for approximately 10 hours at a rate of 1.8 amps. If you use a taper or
trickle charger, it will take longer to charge the battery.
2.
After charging the battery, allow the battery to sit 1-2 hours before checking the state of
charge with a DC volt meter. The charge should be a minimum of 12.5 DC volts. Repeat
the charging cycle if the charge is less than 12.5 DC volts. Replace the battery if it fails
to reach 12.5 volts after the second charge.
08 Maintenance.fm
Page 199
Monday, May 11, 2009
2:03 PM
205
Maintenance
Maintenance
Windshield Trim Panel Removal
Remove the windshield trim panel to access fuse
boxes, the manual windshield adjustment mechanism,
the headlamp adjustment knob and the front turn signal
bulbs.
1.
Lift each panel end upward to release the ends.
2.
Carefully slide the panel slightly toward the wind-
shield to disengage the lower tabs. Remove the
panel.
3.
Unplug the antenna.
4.
Reverse all steps to reinstall the trim panel.
08 Maintenance.fm
Page 205
Monday, May 11, 2009
2:03 PM
214
Maintenance
Maintenance
Fuse Boxes
Remove the windshield trim panel to access the fuses, auto-reset circuit breakers and relays.
See page 205. Use the fuse puller provided in the tool kit to remove a fuse.
Left Fuse Box
Right Fuse Box
08 Maintenance.fm
Page 214
Monday, May 11, 2009
2:03 PM
215
Maintenance
Maintenance
Fuse Replacement
1.
Remove the windshield trim panel. See page 205.
2.
Push the center of the dart upward to remove a fuse box cover panel.
3.
Pull the tab to release a fuse box cover.
Tip:
The reverse system fuse is located on the left rear side of the motorcycle, under the seat
.
NOTICE:
Always use the recommended fuse to prevent electrical system damage. Refer to the label
on the fuse box cover.
Left Fuse Box
Right Fuse Box
Tab
Dart
Reverse System
25 amp mini fuse
(if equipped)
ABS Fuses (if equipped)
08 Maintenance.fm
Page 215
Monday, May 11, 2009
2:03 PM
225
Maintenance
Maintenance
Troubleshooting
Brake Noise / Poor Brake Performance
Tip:
Contact a VICTORY dealer if brake performance does not return after these inspections.
Anti-Lock Brake Light Remains Illuminated or Illuminates Intermittently
Possible Cause
Possible Remedy/Action
Dust / Dirt On Brake Disc(s)
Clean disc. See page 186.
Worn Pads Or Disc / Brake Disc Damage
Inspect pads. See pages 101 and 186.
Brake Fluid Level Low Or Fluid Contaminated
Inspect fluid level / fluid. See pages 97 and 99.
Possible Cause
Possible Remedy/Action
Blown fuse
Check the fuses. See page 214.
Loose or damaged pulse ring
Inspect pulse ring for looseness or chipped teeth.
Debris lodged in components
Inspect wheel speed sensor and pulse ring for debris.
Damage caused by debris
Inspect wheel speed sensor for cracked housing.
Damaged components
See service manual or authorized dealer.
08 Maintenance.fm
Page 225
Monday, May 11, 2009
2:03 PM
261
Specifications
Specifications
All 2010 Vision Models
Fuses
/ Circuit Breakers
Left Fuse Box
Ignition
10A Breaker
Headlight
20A Breaker
Gauges
5A
Radio
25A
Secondary Lights
20A
Horn
20A
Turn Signal / Brake
20A
Right Fuse Box
Engine
15A Breaker
Windshield (Electric)
20A
Fuel Pump / Ignition Coil
15A
Anti-Lock Brake System
30A (2)
9922441.book
Page 261
Monday, May 11, 2009
1:16 PM