Polaris Vegas 8-Ball - 2010 Fuse Box Diagram

Polaris Vegas 8-Ball - 2010 Fuse Box Diagram

25
Safety
Safety and Information Labels
Fuse and Relay Label
(under side cover, on side of fuse box cover)
Fuse Box Removal Instruction Label
(on base of fuse box)
General Representation
29
Component Identification
Right Side View
Drive Belt
(under guard)
Passenger Seat
& Seat Strap
Front
Fork
Front Turn
Signal
Rear
Brake
Pedal
Passenger's
Foot Rest
Engine Oil Fill
Cap/Dipstick
Operator's Foot Rest
Under Right Side Cover:
Rear Brake Fluid Reservoir
Diagnostic Connector
Fuses
Rear Shock Access
Drive Sprocket
(under cover)
Exhaust
Mufflers
General Representation
44
Instruments, Features and Controls
Side Covers
Tip:
Remove the left side cover to access the battery. Remove the
right side cover to access the fuses and the rear brake fluid
reservoir.
1.
Pull outward at each corner of the side cover to disen-
gage the darts.
2.
Remove the side cover from the motorcycle.
3.
To reinstall the side cover, make sure each rubber
grommet is properly located. Align each dart with the
appropriate grommet and press inward firmly to
secure.
Sidestand
The sidestand is located on the left side of the vehicle.
WARNING!
An improperly retracted sidestand could contact the ground during operation and cause loss of control resulting in
serious injury or death. Always make sure the sidestand is fully retracted before operating the motorcycle.
1.
While the motorcycle is in the upright position, push the sidestand downward until it is fully extended.
2.
Slowly lean the motorcycle to the left until the full weight of the motorcycle rests safely on the sidestand.
3.
To retract the sidestand, bring the motorcycle to the upright position. Swing the sidestand upward to its fully
retracted position.
Grommets
90
Maintenance
Rear Suspension
Rear Shock Preload (Ride Height) Adjustment
1.
Rest the motorcycle on the sidestand. Remove the right
side cover. See page 44.
2.
Remove the fuse box. See page 123. Make sure the rear
brake fluid reservoir cap is secure to prevent fluid loss.
3.
Remove the three 10 mm bolts securing the fuse box
bracket to the chassis.
4.
Remove the on-board diagnostics connector from the
fuse box bracket by squeezing the connector lock and
pulling the connector apart. Leave the terminated end
attached to the fuse box bracket.
5.
Remove the wire harness dart from the fuse box
bracket by sliding the connector off the dart clip.
6.
Carefully pull and rotate the fuse box bracket toward
the front of the motorcycle.
10 mm Bolts
91
Maintenance
Rear Suspension
Rear Shock Preload (Ride Height) Adjustment
7.
The upper spanner nut on the shock is the lock nut. The
lower spanner nut is the adjuster nut. Loosen the lock
nut by turning it counterclockwise (as viewed from the
top of shock) with the spanner wrench.
8.
Spray a light lubricant on the adjuster nut where it
contacts the spring. DO NOT allow spray to contact the
drive belt.
9.
Adjust shock preload by rotating the adjuster nut
clockwise (as viewed from the top of shock) to
INCREASE preload (firm) or counterclockwise to
DECREASE preload (softer).
10.
Recheck the preload measurement after adjusting.
11.
Tighten the lock nut securely against the adjuster nut.
12.
Reinstall the fuse box bracket and tighten the bolts
securely.
13.
Reinstall the fuse box and right side cover.
Increase
Preload
(more firm)
Decrease
Preload
(softer)
Adjuster
Nut
(lower)
Lock Nut
(upper)
115
Maintenance
Seat Removal
WARNING!
A loose seat could cause a sudden shift in riding position, causing loss of control. Always make sure the seats are
securely fastened before riding the motorcycle.
1.
Remove the side covers.
2.
Remove the fuse box from the bracket.
3.
Remove the two screws (left and right) securing the seat to the frame.
4.
Lift the rear of the seat and pull rearward and upward to remove it.
Seat Installation
1.
Slide the seat tongue into the rubber mount at the rear of the fuel tank. Push down on the rear of the seat until the
screw holes align.
2.
Ensure the front seat mount is engaged in the front rubber mount, then install the screws and tighten securely.
3.
Reinstall the fuse box.
4.
Reinstall the side covers.
123
Maintenance
Fuse Replacement
1.
Remove the right side cover.
2.
Lift the release tab and slide the fuse box rearward to remove
it from the bracket. Release the tabs on each side of the fuse
box cover and remove the cover.
3.
Remove the damaged fuse and seat the new fuse firmly in its
place.
4.
Reinstall the fuse box cover with the double cutout toward
the front of the motorcycle.
5.
Reinstall the fuse box and the side cover.
NOTICE:
Use fuses with the recommended amperage to avoid damage
to the electrical system.
Fuse Recommendations
Fuse Application
Fuse Size
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlamp / Brake Lamp
20 amp
Tail Lamp, Flashers, Indicator Lamp, Horn
15 amp
Ignition / Gauges
15 amp
Accessory Fuse (for emergency use)
(motorcycle will operate without fuse)
15 amp
Release Tab
137
Storage
Tire Inflation
Verify that tire pressure is at specification. See page 110. Check and adjust tire pressure as needed during the storage
period.
Battery Care
1.
Remove the battery. See page 117.
2.
Clean oxidation from battery posts and cable connectors with a wire brush. Wash the posts and cable connectors
with a solution of one part baking soda to 16 parts water. Rinse with clean water and wipe dry. Apply a thin film
of dielectric grease to the posts and cable connectors.
3.
Clean the outside of the battery with a solution of mild detergent and warm water.
4.
Store the battery in a dry area with a temperature of 32° to 90°F (0° to 32° C).
5.
While in storage, fully charge the battery monthly. If the motorcycle will not be used for a period of six weeks or
longer, a maintenance charger should be connected to the battery. See page 118. A fused maintenance charger
connection is provided under the left side cover. The connector is designed for use with the VICTORY
maintenance charger.
153
Specifications
Tip:
Dimensions and specifications may vary with features, options and accessories.
Model Year 2010
VEGAS
KINGPIN
Wheels and Tires
Front Wheel Type / Size
Cast 18 x 3.5 or Billet 21 x 2.15
Cast 18 x 3.5 or Billet 18 x 3.0
Rear Wheel Type / Size
Cast 18 x 5.5 or Billet 18 x 5.0
Cast 18 x 5.5 or Billet 18 x 5.0
Front Tire Type / Size
Dunlop Elite 3 / 90/90 2154H
Dunlop 491 Elite ll / 130/70 B18 63H
Rear Tire Type / Size
Dunlop D417 / 180/55 B18 74H
Dunlop D417 / 180/55 B18 74H
Electrical
Alternator
38 Amp Max Output
38 Amp Max Output
Battery
12 Volts 18 Amp Hour
12 Volts 18 Amp Hour
Fuse, Engine / ECM
15 amp
15 amp
Fuse, Fuel Pump
10 amp
10 amp
Fuse, Headlight / Brake Light Lamps
20 amp
20 amp
Fuse, Tail Light Lamps / Flashers / Indicator
Lamps / Horn
15 amp
15 amp
Fuse, Ignition / Gauges
15 amp
15 amp
Fuse, Accessory
15 amp
15 amp
Bulb, Headlight (International)
High H11 / Low H11
High H11 / Low H11
Bulb, Taillight
Non-Serviceable LED
Non-Serviceable LED
Bulb, Turn Signal
R10W
R10W
Bulb, Indicator
2.3 Watt Wedge Base
2.3 Watt Wedge Base