Polaris Hammer S - 2010 Fuse Box Diagram

Polaris Hammer S - 2010 Fuse Box Diagram

24
Safety
Safety and Information Labels
Fuse and Relay Label
(under side cover, on side of fuse box cover)
Fuse Box Removal Instruction Label
(on base of fuse box)
28
Component Identification
Right Side View
Drive Belt
(under guard)
Passenger Seat/Cowl
Seat Strap (under cowl)
Front
Fork
Front Turn
Signal
Rear
Brake
Pedal
Front Brake
Caliper
Passenger's
Foot Rest
Engine Oil Fill
Cap/Dipstick
Operator's Foot Rest
Under Right Side Cover:
Rear Brake Fluid Reservoir
Diagnostic Connector
Fuses
Rear Shock Access
Drive Sprocket
(under cover)
Exhaust
Mufflers
42
Instruments, Features and Controls
Side Covers
Tip:
Remove the left side cover to access the battery. Remove the
right side cover to access the fuses and the rear brake fluid
reservoir.
1.
Pull outward at each corner of the side cover to disen-
gage the darts.
2.
Remove the side cover from the motorcycle.
3.
To reinstall the side cover, make sure each rubber
grommet is properly located. Align each dart with the
appropriate grommet and press inward firmly to
secure.
Sidestand
The sidestand is located on the left side of the vehicle.
WARNING!
An improperly retracted sidestand could contact the ground during operation and cause loss of control resulting in
serious injury or death. Always make sure the sidestand is fully retracted before operating the motorcycle.
1.
While the motorcycle is in the upright position, push the sidestand downward until it is fully extended.
2.
Slowly lean the motorcycle to the left until the full weight of the motorcycle rests safely on the sidestand.
3.
To retract the sidestand, bring the motorcycle to the upright position. Swing the sidestand upward to its fully
retracted position.
Grommets
88
Maintenance
Rear Suspension
Rear Shock Preload (Ride Height) Adjustment
1.
Rest the motorcycle on the sidestand. Remove the right
side cover. See page 42.
2.
Remove the fuse box. See page 118. Make sure the rear
brake fluid reservoir cap is secure to prevent fluid loss.
3.
Remove the three 10 mm bolts securing the fuse box
bracket to the chassis.
4.
Remove the on-board diagnostics connector from the
fuse box bracket by squeezing the connector lock and
pulling the connector apart. Leave the terminated end
attached to the fuse box bracket.
5.
Remove the wire harness dart from the fuse box
bracket by sliding the connector off the dart clip.
6.
Carefully pull and rotate the fuse box bracket toward
the front of the motorcycle.
10 mm Bolts
89
Maintenance
Rear Suspension
Rear Shock Preload (Ride Height) Adjustment
7.
The upper spanner nut on the shock is the lock nut. The
lower spanner nut is the adjuster nut. Loosen the lock
nut by turning it counterclockwise (as viewed from the
top of shock) with the spanner wrench.
8.
Spray a light lubricant on the adjuster nut where it
contacts the spring. DO NOT allow spray to contact the
drive belt.
9.
Adjust shock preload by rotating the adjuster nut
clockwise (as viewed from the top of shock) to
INCREASE preload (firm) or counterclockwise to
DECREASE preload (softer).
10.
Recheck the preload measurement after adjusting.
11.
Tighten the lock nut securely against the adjuster nut.
12.
Reinstall the fuse box bracket and tighten the bolts
securely.
13.
Reinstall the fuse box and right side cover.
Increase
Preload
(more firm)
Decrease
Preload
(softer)
Adjuster
Nut
(lower)
Lock Nut
(upper)
118
Maintenance
Fuse Replacement
1.
Remove the right side cover.
2.
Lift the release tab and slide the fuse box rearward to remove
it from the bracket. Release the tabs on each side of the fuse
box cover and remove the cover.
3.
Remove the damaged fuse and seat the new fuse firmly in its
place.
4.
Reinstall the fuse box cover with the double cutout toward
the front of the motorcycle.
5.
Reinstall the fuse box and the side cover.
NOTICE:
Use fuses with the recommended amperage to avoid damage
to the electrical system.
Fuse Recommendations
Fuse Application
Fuse Size
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlamp / Brake Lamp
15 amp
Tail Lamp, Flashers, Indicator Lamp, Horn
15 amp
Ignition / Gauges
15 amp
Accessory Fuse (for emergency use)
(motorcycle will operate without fuse)
15 amp
Release Tab
138
Storage
Tire Inflation
Verify that tire pressure is at specification. See page 108. Check and adjust tire pressure as needed during the storage
period.
Battery Care
1.
Remove the battery. See page 115.
2.
Clean oxidation from battery posts and cable connectors with a wire brush. Wash the posts and cable connectors
with a solution of one part baking soda to 16 parts water. Rinse with clean water and wipe dry. Apply a thin film
of dielectric grease to the posts and cable connectors.
3.
Clean the outside of the battery with a solution of mild detergent and warm water.
4.
Store the battery in a dry area with a temperature of 32° to 90° F (0° to 32° C).
5.
While in storage, fully charge the battery monthly. If the motorcycle will not be used for a period of six weeks or
longer, a maintenance charger should be connected to the battery. See page 116. A fused maintenance charger
connection is provided under the left side cover. The connector is designed for use with the VICTORY
maintenance charger.
154
Specifications
Tip:
Dimensions and specifications may vary with features, options and accessories.
2010 HAMMER
Wheels and Tires
Front Wheel Type / Size
Cast 18 x 3.5 or Billet 18 x 3.0
Rear Wheel Type / Size
Cast or Billet 18 x 8.5
Front Tire Type / Size
Dunlop Elite 3 / 130/70R18 63H Tubeless
Rear Tire Type / Size
Dunlop Elite 3 / 250/40R18 81V Tubeless
Electrical
Alternator
38 Amp Max Output
Battery
12 Volts 18 Amp Hour
Fuse, Engine / ECM
15 amp
Fuse, Fuel Pump
10 amp
Fuse, Headlight / Brake Light Lamps
15 amp
Fuse, Tail Light Lamps / Flashers / Indicator Lamps / Horn
15 amp
Fuse, Ignition / Gauges
15 amp
Fuse, Accessory
15 amp
Bulb, Headlight (International)
High H11 / Low H11 (HAMMER)
High H8 / Low H11 (HAMMER 8-BALL)
Bulb, Taillight
Non-Serviceable LED
Bulb, Turn Signal
R10W
Bulb, Indicator
2.3 Watt Wedge Base