Polaris Cross Roads - 2010 Fuse Box Diagram

Polaris Cross Roads - 2010 Fuse Box Diagram

39
Identification
Identification
Component Locations
1.
Exhaust Mufflers
2.
Drive Belt Guard
3.
Drive Sprocket (under cover)
4.
Engine Oil Fill Cap / Dipstick
5.
Rear Brake Fluid Reservoir
6.
Rear Brake Pedal
7.
Air Filter
8.
Headlamp
9.
Mirror
10. Fuel Tank
11. Access Cover
12. Fuse Box (under cover)
13. Accessory Fuse (under cover)
14. Rear Shock Air Fitting (under cover)
15. Radio Antenna (if equipped)
16. License Plate Bracket
2
3
4
6
12
14
1
8
7
5
16
15
9
10
13
11
9922671.book
Page 39
Tuesday, June 16, 2009
12:06 PM
40
Identification
Identification
Component Locations
1.
Windshield
2.
Clutch Lever
3.
Fuel Filler Cap
4.
Operator Seat
5.
Passenger Seat
6.
Saddlebag Latch
7.
Turn Signals
8.
Tail Lamps
9.
Front Brake Lever
10. Front Brake Fluid Reservoir
11. Radio Fuse (inside fairing)
1
2
4
5
9
10
3
6
7
8
11
9922671.book
Page 40
Tuesday, June 16, 2009
12:06 PM
69
Controls
Instruments/Features/Controls
Right Handlebar Switches
Engine Starter Switch
The starter switch is located on the right handlebar. Use the
starter switch to start the engine and operate in reverse (if
equipped). The switch will operate only when the engine stop/
run switch is in the RUN position and the transmission is in
neutral (or the clutch is disengaged). The reverse lever (if
equipped) must also be disengaged.
Tip:
If the reverse system fuse has blown, the starter switch will not
function even if the reverse lever is disengaged. Replace the fuse.
See page 207.
Read the engine starting procedures before starting the engine.
See page 108.
Press the right side of the starter switch to engage the starter
motor.
See page 125 for reverse operation.
Starter Switch
9922671.book
Page 69
Tuesday, June 16, 2009
12:06 PM
80
Controls
Instruments/Features/Controls
Tool Kit
The tool kit can be used to perform most basic
maintenance items. Tools provided in the tool kit
include:
1.
4 mm Ball Drive Allen Wrench
2.
5 mm Ball Drive Allen Wrench
3.
6 mm Ball Drive Allen Wrench
4.
4 mm / 6 mm Open End Wrench
5.
8 mm / 10 mm Open End Wrench
6.
Combination Phillips / Slot Screw Driver
7.
Rear Shock Absorber / Tire Pressure Gauge
8.
Fuse Puller
1
4
3
5
6
7
8
2
9922671.book
Page 80
Tuesday, June 16, 2009
12:06 PM
196
Maintenance
Maintenance
Battery Charging
Tip:
If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance
charger should be connected to the battery. A fused maintenance charger connection is provided.
The connector is designed for use with the VICTORY accessory maintenance charger available at
your authorized VICTORY dealer.
1.
Following the charger manufacturer’s instructions, use a battery charger designed for use
with 12-volt batteries. The charger should have a maximum charging rate of 1.8 amps.
Charge the battery for approximately 10 hours at a rate of 1.8 amps. If you use a taper or
trickle charger, it will take longer to charge the battery.
2.
After charging the battery, allow the battery to sit 1-2 hours before checking the state of
charge with a DC volt meter. The charge should be a minimum of 12.5 DC volts. Repeat
the charging cycle if the charge is less than 12.5 DC volts. Replace the battery if it fails
to reach 12.5 volts after the second charge.
9922671.book
Page 196
Tuesday, June 16, 2009
12:06 PM
199
Maintenance
Maintenance
Side Covers
Remove the left side cover to access the electronic con-
trol module, diagnostic connector and chassis-to-engine
harness connector.
Remove the right side cover to access the fuses, rear
suspension air fitting, clutch cable adjuster, purge valve
and flasher unit.
Remove both side covers to access the seat screws.
1.
Pull outward at each corner of the side cover to dis-
engage the three darts.
2.
Remove the side cover from the motorcycle.
3.
To reinstall the side cover, make sure each rubber
grommet is properly positioned. Align each dart
with the appropriate grommet and press inward
firmly to secure each dart.
Grommets
9922671.book
Page 199
Tuesday, June 16, 2009
12:06 PM
206
Maintenance
Maintenance
Fuse Replacement
NOTICE:
Use fuses with the recommended amperage to avoid damage to the electrical system.
Fuse Recommendations
Fuse Application
Fuse Size
Engine
15 amp
Fuel Pump/Ignition Coil
15 amp
Lights
20 amp
Turn Signals/Horn
10 amp
Ignition
10 amp
Chassis
20 amp
Fuse Box Label
9922671.book
Page 206
Tuesday, June 16, 2009
12:06 PM
207
Maintenance
Maintenance
Fuse Replacement
Tip:
Use the fuse puller provided in the tool kit to remove
a fuse.
1.
Remove the right side cover.
2.
Lift the release tab and slide the fuse box
upward to remove it from the bracket. Release
the tabs on each side of the fuse box cover and
remove the cover.
Tip:
The reverse fuse (if equipped) is located on the
debris flap at the front of the rear tire.
3.
Remove the damaged fuse and seat the new
fuse firmly in its place.
4.
Reinstall the fuse box cover with the double
cut-out to the left (with print readable from
right side of motorcycle).
5.
Reinstall the fuse box and the side cover.
Fuse Box
9922671.book
Page 207
Tuesday, June 16, 2009
12:06 PM
254
Specifications
Specifications
Cross Roads / Cross Country
Fuses
/ Circuit Breakers
Engine
15A
Fuel Pump/Ignition Coil
15A
Lights
20A
Turn Signals/Horn
10A
Ignition
10A
Chassis
20A
9922671.book
Page 254
Tuesday, June 16, 2009
12:06 PM