Polaris Ness Signature Series Vegas Jackpot - 2009 Fuse Box Diagram

Polaris Ness Signature Series Vegas Jackpot - 2009 Fuse Box Diagram

25
SAFETY
Location of Safety and Vehicle Information Labels
Label content varies by model. The labels shown illustrate type and location only. Always refer to the label on your
motorcycle for model-specific information.
Location F
FUSE and RELAY LOCATION
(Under side cover, on side of fuse box cover)
FUSE BOX REMOVAL INSTRUCTION
(on base of fuse box)
17
15
9
10
11
14
13
12
1
2
5
6
4
3
8
7
16
32
COMPONENT IDENTIFICATION
RIGHT SIDE VIEW
1.
Drive Belt (under guard)
2.
Passenger Seat
3.
Seat Strap
4.
Operator’s Seat
5.
Side Cover
6.
Rear Shock Absorber (access through RH side cover)
7.
Front Turn Signal
8.
Front Fork
9.
Rear Brake Pedal
10. Operator Foot Rest
11. Engine Oil Fill Cap/Dipstick
12. Drive Sprocket (under cover)
13. Rear Brake Fluid Reservoir (under side cover)
14. Fuses (under side cover)
15. Passenger Foot Rest
16. Diagnostic Connector
17. Exhaust Mufflers
46
INSTRUMENTS, FEATURES AND CONTROLS
Side Covers
Your motorcycle is equipped with two removable side covers.
Remove the left side cover to access the battery. Remove the
right side cover to access the fuses and the rear brake fluid
reservoir.
To remove right side cover, pull carefully at each dart
location indicated by arrows in the photo at right. Remove
cover from the motorcycle. Remove left side cover in the
same manner. Be sure rubber grommets are in place before
reversing the above procedure to install the side covers.
Sidestand
The sidestand is located on the left side of the motorcycle.
Correctly retract the sidestand before operating the motorcycle. An improperly retracted sidestand could
come into contact with the ground and cause loss of control.
WARNING
To extend the sidestand, swing it out from the end until it is fully extended. Lean the motorcycle toward the
sidestand until the sidestand firmly supports the motorcycle.
To retract the sidestand, lean the motorcycle away from the sidestand until the motorcycle is fully upright. Swing
the sidestand back into its fully retracted position.
96
MAINTENANCE
Rear Suspension
Adjust Rear Shock Absorber Preload (Ride Height)
To adjust the shock absorber spring pre-load:
1.
Rest the motorcycle on the sidestand. Remove the right side
cover (page 46).
2.
Remove the fuse box from right panel by lifting upward on
the tab at the rearward end while pulling the fuse box
rearward (page 131). Make sure that the rear brake fluid
reservoir cap is secured to prevent fluid loss (page 115).
3.
Remove three 10mm bolts (1) holding the fuse box bracket
to chassis.
4.
Remove the on-board diagnostics connector from the fuse
box bracket by squeezing the connector lock and pulling the
connector apart. Leave the terminated end attached to the
fuse box bracket.
5.
Remove the wire harness dart from the fuse box bracket by
sliding the connector off the dart clip.
6.
Carefully pull and rotate the fuse box bracket toward the front of the motorcycle.
(Continued on next page)
1
97
MAINTENANCE
Rear Suspension
Adjust Rear Shock Absorber Preload (Ride Height) (Cont.)
7.
The uppermost spanner nut on the shock is the locknut. The
spanner nut closest to the spring is the adjuster nut. Loosen the
locknut by turning it counterclockwise (as viewed from the top
of shock absorber) with the spanner wrench.
8.
Spray a light lubricant on the adjuster nut where it contacts the
spring. DO NOT allow spray to contact the drive belt.
9.
Adjust shock absorber preload by rotating adjuster nut
clockwise (as viewed from the top of shock absorber) to
INCREASE the ride height measurement (firm), and
counterclockwise to DECREASE the ride height measurement
(softer). Recheck ride height dimension after adjustment.
10. Tighten lock nut securely against adjuster nut when adjustment
is complete.
11. Reinstall fuse box bracket and securely tighten the 3 bolts that
secure panel to chassis.
12. Reinstall fuse box and right side cover.
1. Preload Adjustment Locknut
2. Preload Adjuster Nut
3. Increase Ride Height Measurement
4. Decrease Ride Height Measurement
1
3
4
2
121
MAINTENANCE
Wheels
Inspect both wheels for cracks or damage. If you see wheel
damage or cracks, contact an authorized VICTORY dealer to
have the wheel(s) replaced.
Do not operate the motorcycle if wheels are damaged or
cracked.
WARNING
126
MAINTENANCE
Seat Installation
1.
To reinstall the seat, slide the tongue of the seat into
the rubber mount at rear of fuel tank. Push down on
the rear of the seat until the screw holes align.
2.
Ensure the front seat mount is engaged in the front
rubber mount, then install the screws and tighten
securely.
3.
Reinstall the fuse box (if removed).
4.
Reinstall the left and right side covers.
Always make sure the seats are securely fastened before riding the motorcycle. A loose seat could cause a
sudden shift in riding position, causing loss of control.
WARNING
127
MAINTENANCE
Battery
The battery contains sulfuric acid, which can cause severe burns. Do not allow sulfuric acid to contact
skin, eyes, or clothing.
Antidotes:
External: Flush with water.
Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten eggs, or
vegetable oil. Call physician immediately.
Eyes: Flush with water for 15 minutes and get prompt medical attention.
WARNING
The motorcycle uses a permanently sealed, maintenance-free battery. Do not remove the battery cap strip for any
reason. Keep the battery connections clean and tight at all times.
NOTE:
If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance charger should be con-
nected to the battery. A fused maintenance charger connection is provided beneath the left side cover. The connector
is designed for use with the VICTORY maintenance charger available from your authorized VICTORY dealer.
131
MAINTENANCE
Fuses
Notice
Use only recommended amperage fuses to avoid damage to the electrical system.
1.
Remove the right side cover. Release the fuse box from the bracket by
lifting the tab (1) and sliding the fuse box rearward (see diagram below
right.)
2.
Release the tabs on each side of the fuse box cover and remove the
cover.
3.
Remove the damaged fuse from the fuse box and seat the new fuse
firmly in its place. A spare 15 amp fuse is located in the fuse box.
4.
Reinstall the fuse box cover with the double cutout toward the front of
the motorcycle. Reinstall the fuse box to the bracket.
5.
Reinstall the side cover.
Fuse Application
Fuse Size
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlight / Brake Light Lamp
20 amp
Taillight Lamp, Flashers, Indicator Lamp, Horn
15 amp
Ignition / Gauges
15 amp
Accessory Fuse (for emergency use)
(Bike will operate without fuse)
15 amp
1
160
SPECIFICATIONS
Model Year 2009
VEGAS JACKPOT / NESS JACKPOT
Wheels and Tires
Front Wheel Type/Size
Cast or Billet- 21 x 2.15
Rear Wheel Type Size
Cast or Billet- 18 x 8.5
Front Tire Type/Size
Dunlop Elite 3
(90/90 21 54H Tubeless)
Rear Tire Type/Size
Dunlop Elite 3
(250/40R18 Tubeless)
Electrical
Alternator
38 Amp Max Output
Battery
YTX20HL-BS / 12 Volts 18 Amp Hour / 310 CCA
Lights and Fuses
Fuses
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlight / Brake Light Lamp
20 amp
Taillight Lamp, Flashers, Indicator Lamps, Horn
15 amp
Ignition / Gauges
15 amp
Accessory
15 amp
Bulbs
Headlight (International)
High H11 / Low H11
Taillight
Non-Serviceable LED
Turn Signal
R10W (Auto-Cancel System)
Indicator
2.3 Watt Wedge Base
NOTE: Dimensions and specifications may vary with features, options and accessories.