Polaris Hammer - 2009 Fuse Box Diagram

Polaris Hammer - 2009 Fuse Box Diagram

25
SAFETY
Location of Safety and Vehicle Information Labels
Label content varies by model. The labels shown illustrate type and location only. Always refer to the label on your
motorcycle for model-specific information.
Location F
FUSE and RELAY LOCATION
(Under side cover, on side of fuse box cover)
FUSE BOX REMOVAL INSTRUCTION
(on base of fuse box)
32
COMPONENT IDENTIFICATION
RIGHT SIDE VIEW
1.
Drive Belt (under guard)
2.
Passenger Seat / Cowl
3.
Seat Strap (Under Seat Cowl)
4.
Operator’s Seat
5.
Rear Shock Absorber (access through RH side cover)
6.
Side Cover
7.
Front Turn Signal
8.
Front Fork
9.
Front Brake Caliper
10. Rear Brake Pedal
11. Operator Foot Rest
12. Engine Oil Fill Cap/Dipstick
13. Drive Sprocket (under cover)
14. Rear Brake Fluid Reservoir (under side cover)
15. Fuses (under side cover)
16. Passenger Foot Rest
17. Diagnostic Connector
18. Exhaust Muffler (2)
1
2
18
16
8
7
10
11
15
14
13
12
5
6
4
3
9
17
46
INSTRUMENTS, FEATURES AND CONTROLS
Side Covers
Your motorcycle is equipped with two removable side covers.
Remove the left side cover to access the battery. Remove the
right side cover to access the fuses and the rear brake fluid
reservoir.
To remove either side cover, pull the lower corners of the side
cover out slightly until lower dart (A) is disengaged. Pull
evenly on upper left and right side to disengage the two top
darts (B). Remove cover from the motorcycle. Be sure rubber
grommets are in place before reversing the above procedure
to install the side covers.
Sidestand
The sidestand is located on the left side of the motorcycle.
Correctly retract the sidestand before operating the motorcycle. An improperly retracted sidestand could
come into contact with the ground and cause loss of control.
WARNING
To extend the sidestand, swing it out from the end until it is fully extended. Lean the motorcycle toward the
sidestand until the sidestand firmly supports the motorcycle.
To retract the sidestand, lean the motorcycle away from the sidestand until the motorcycle is fully upright. Swing
the sidestand back into its fully retracted position.
96
MAINTENANCE
Rear Suspension
Adjust Rear Shock Absorber Preload (Ride Height)
To adjust the shock absorber spring pre-load:
1.
Rest the motorcycle on the sidestand. Remove the right side
cover (page 46).
2.
Remove the fuse box from right panel by lifting upward on
the tab at the rearward end while pulling the fuse box
rearward (page 130). Make sure that the rear brake fluid
reservoir cap is secured to prevent fluid loss (page 115).
3.
Remove three 10mm bolts (1) holding the fuse box bracket
to chassis.
4.
Remove the on-board diagnostics connector from the fuse
box bracket by squeezing the connector lock and pulling the
connector apart. Leave the terminated end attached to the
fuse box bracket.
5.
Remove the wire harness dart from the fuse box bracket by
sliding the connector off the dart clip.
6.
Carefully pull and rotate the fuse box bracket toward the front of the motorcycle.
(Continued on next page)
1
97
MAINTENANCE
Rear Suspension
InspectRear Shock Absorber Preload (Ride Height)
7.
The uppermost spanner nut on the shock is the locknut (1). The
spanner nut closest to the spring is the adjuster nut (2). Loosen the
locknut by turning it counterclockwise (as viewed from the top of
shock absorber) with the spanner wrench.
8.
Spray a light lubricant on the adjuster nut where it contacts the
spring. DO NOT allow spray to contact the drive belt.
9.
Adjust shock absorber preload by rotating adjuster nut clockwise (as
viewed from the top of shock absorber) to INCREASE the ride
height measurement (firm), and counterclockwise to DECREASE
the ride height measurement (softer). Recheck ride height
dimension after adjustment.
10. Tighten lock nut securely against adjuster nut when adjustment is
complete.
11. Reinstall fuse box bracket and securely tighten the 3 bolts that
secure panel to chassis.
12. Reinstall fuse box and right side cover.
1. Preload Adjustment Locknut
2. Preload Adjuster Nut
3. Increase Ride Height Measurement
4. Decrease Ride Height Measurement
1
3
4
2
126
MAINTENANCE
Battery
The battery contains sulfuric acid, which can cause severe burns. Do not allow sulfuric acid to contact
skin, eyes, or clothing.
Antidotes:
External: Flush with water.
Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten eggs, or
vegetable oil. Call physician immediately.
Eyes: Flush with water for 15 minutes and get prompt medical attention.
WARNING
The motorcycle uses a permanently sealed, maintenance-free battery. Do not remove the battery cap strip for any
reason. Keep the battery connections clean and tight at all times.
NOTE:
If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance charger should be connected
to the battery. A fused maintenance charger connection is provided beneath the left side cover. The connector is designed
for use with the VICTORY maintenance charger available at your authorized VICTORY dealer.
130
MAINTENANCE
Fuses
Notice
Use only recommended amperage fuses to avoid damage to the electrical system.
1.
Remove the right side cover. Release the fuse box from the bracket by
lifting the tab (1) and sliding the fuse box rearward (see diagram below
right.)
2.
Release the tabs on each side of the fuse box cover and remove the
cover.
3.
Remove the damaged fuse from the fuse box and seat the new fuse
firmly in its place. A spare 15 amp fuse is located in the fuse box.
4.
Reinstall the fuse box cover with the double cutout toward the front of
the motorcycle. Reinstall the fuse box to the bracket.
5.
Reinstall the side cover.
Fuse Application
Fuse Size
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlight / Brake Light Lamps
20 amp
Taillight Lamp, Flashers, Indicator Lamp, Horn
15 amp
Ignition / Gauges
15 amp
Accessory Fuse (for emergency use)
(Bike will operate without fuse)
15 amp
1
159
SPECIFICATIONS
Model Year 2009
HAMMER
Wheels and Tires
Front Wheel Type/Size
Cast 18 x 3.5 or Billet 18 x 3.0
Rear Wheel Type Size
Cast or Billet 18 x 8.5
Front Tire Type/Size
Dunlop Elite 3 / 130/70R18
Rear Tire Type/Size
Dunlop Elite 3 / 250/40R18
Electrical
Alternator
38 Amp Max Output
Battery
12 Volts 18 Amp Hour
Lights and Fuses
Fuses
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlight / Brake Light Lamps
20 amp
Tail Light Lamps / Flashers / Indicator Lamps / Horn
15 amp
Ignition / Gauges
15 amp
Accessory
15 amp
Bulbs
Headlight (International)
High H11 / Low H11
Taillight
Non-Serviceable LED
Turn Signal
R10W
Indicator
2.3 Watt Wedge Base
NOTE: Dimensions and specifications may vary with features, options and accessories.