Polaris Hammer - 2005 Fuse Box Diagram

Polaris Hammer - 2005 Fuse Box Diagram

25
SAFETY
Location of Safety and Vehicle Information Labels
Location F
FUSE and RELAY LOCATION
(Under side cover, on side of fuse box cover)
FUSE BOX REMOVAL
(on base of fuse box)
32
COMPONENT IDENTIFICATION
RIGHT SIDE VIEW
1.
Drive Belt (under guard)
2.
Passenger Seat / Cowl
3.
Seat Strap
4.
Operator’s Seat
5.
Rear Shock Absorber (access through RH side cover)
6.
Side Cover
7.
Front Turn Signal
8.
Front Fork
9.
Oil Cooler
10. Rear Brake Pedal
11. Operator Foot Rest
12. Engine Oil Fill Cap/Dipstick
13. Engine Oil Drain Plug (under engine)
14. Drive Sprocket (under cover)
15. Rear Brake Fluid Reservoir (under side cover)
16. Fuses (under side cover)
17. Passenger Foot Rest
18. Exhaust Muffler (2)
19. Front Brake Caliper4
1
2
18
17
8
7
10
11
12
9
16
15
14
13
5
6
4
3
19
46
INSTRUMENTS, FEATURES AND CONTROLS
Side Covers
Your motorcycle is equipped with two removable side covers. Remove the left side cover to access the battery.
Remove the right side cover to access the fuses and the rear brake fluid reservoir.
To remove either side cover, pull the lower corners of the side cover out slightly until lower dart is disengaged. Pull
evenly on upper left and right side to disengage the two top darts. Remove cover from the motorcycle. Be sure
rubber grommets are in place before reversing the above procedure to install the side covers.
Sidestand
The sidestand is located on the left side of the motorcycle.
Correctly retract the sidestand before operating the motorcycle. An improperly retracted sidestand
could come into contact with the ground and cause loss of control.
WARNING
To extend the sidestand, swing it out from the end until it is fully extended. Lean the motorcycle toward the
sidestand until the sidestand firmly supports the motorcycle.
To retract the sidestand, lean the motorcycle away from the sidestand until the motorcycle is fully upright. Swing
the sidestand back into its fully retracted position.
95
MAINTENANCE
Rear Suspension
Adjust Rear Shock Absorber Preload (Ride Height)
1.
To adjust the shock absorber spring pre-load:
1. Rest the motorcycle on the sidestand. Remove the right
side cover (page 46).
2. Remove the fuse box from right panel by lifting upward
on the tab at the forward end while pulling the fuse box forward
(page 127). Make sure that the rear brake fluid reservoir cap is
secured to prevent fluid loss (page 111).
3. Remove three (10mm) bolts (A) holding the fuse box
bracket to chassis.
4. Remove the wire harness dart (B) from the fuse box bracket by squeezing the tabs with a long nose
pliers.
5. Carefully pull and rotate the fuse box bracket toward the front of the motorcycle.
A
B
96
MAINTENANCE
Rear Suspension
InspectRear Shock Absorber Preload (Ride Height)
2.
The uppermost spanner nut on the shock is the locknut (1). The
spanner nut closest to the spring is the adjuster nut (2). Loosen the
locknut by turning it counterclockwise (as viewed from the top of
shock absorber) with the spanner wrench.
3.
Spray a light lubricant on the adjuster nut where it contacts the
spring. DO NOT allow spray to contact the drive belt.
4.
Adjust shock absorber preload by rotating adjuster nut clockwise (as
viewed from the top of shock absorber) to INCREASE the ride
height measurement (firm), and counterclockwise to DECREASE
the ride height measurement (softer). Re-check ride-height
dimension after adjustment.
5.
Tighten lock nut securely against adjuster nut when adjustment is
complete.
6.
Reinstall fuse box bracket and securely tighten the 3 bolts that
secure panel to chassis.
7.
Re-install fuse box and right side cover.
1. Preload Adjustment Locknut
2. Preload Adjuster Nut
3. Increase Ride Height Measurement
4. Reduce Ride Height Measurement
1
3
4
2
123
MAINTENANCE
Battery
The battery contains sulfuric acid, which can cause severe burns. Do not allow sulfuric acid to
contact skin, eyes, or clothing.
Antidotes:
External: Flush with water.
Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten eggs, or
vegetable oil. Call physician immediately.
Eyes: Flush with water for 15 minutes and get prompt medical attention.
WARNING
The motorcycle uses a permanently sealed, maintenance-free battery. Do not remove the battery cap strip for any
reason. Keep the battery connections clean and tight at all times.
Notice
If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance charger
should be connected to the battery. A fused maintenance charger connection is provided beneath the left side cover. The
connector is designed for use with the VICTORY maintenance charger available at your authorized VICTORY dealer.
127
MAINTENANCE
Fuses
Use only recommended amperage fuses to avoid damage to the electrical system.
Caution
1.
Remove right side cover and release fuse box from bracket by lifting tab (A)
and sliding the fuse box forward (see diagram below right.)
2.
Release tabs on each side of fuse box cover, and remove cover.
3.
Remove fuse from fuse box and push new fuse firmly in its place. A spare 15
amp fuse is located in the fuse box.
4.
Reinstall the fuse box cover with the double cutout toward the front of the
motorcycle. The fuse box decal should be readable from the right side of the
motorcycle.
5.
Reinstall the fuse box to the bracket.
6.
Reinstall the side cover.
Fuse Application
Fuse Size
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlamp / Brake Lamp
15 amp
Tail Lamp, Flashers, Indicator Lamp, Horn
15 amp
Ignition / Gauges
15 amp
Spare Fuse
15 amp
A
156
SPECIFICATIONS
Model Year 2005
HAMMER
Wheels and Tires
Front Wheel Type/Size
Cast or Billet - 18 x 3.0
Rear Wheel Type Size
Cast or Billet - 18 x 8.5
Front Tire Type/Size
Dunlop Elite 3
(130/70R18)
Rear Tire Type/Size
Dunlop Elite 3
(250/40R18)
Electrical
Alternator
38 Amp Max Output
Battery
12 Volts 18 Amp Hour
Lights and Fuses
Fuses
Engine / ECM
15 amp
Fuel Pump
10 amp
Headlamp / Brake Lamp
15 amp
Tail Lamp, Flashers,
Indicator Lamps, Horn
15 amp
Ignition / Gauges
15 amp
Bulbs
Headlamp (International)
High: H8 / Low H11 (H4)
Taillight
Non-Serviceable LED
Turn Signal
R10W
Indicator
2.3 Watt Wedge Base
NOTE: Dimensions and specifications may vary with features, options and accessories.