Polaris 600 PRO-RMK - 2016 Fuse Box Diagram

Polaris 600 PRO-RMK - 2016 Fuse Box Diagram

35
FEATURES
12-Volt DC Power Receptacle
If equipped, the 12-volt DC power
receptacle is located on the hood next
to the instrument cluster. The 12-volt
power receptacle is protected by a 2
amp mini blade fuse located in the
protective bag above the clutch
cover.
Use of the 12-volt DC power
receptacle is recommended for
connecting power-sensitive devices
such as GPS units and cell phones.
NOTE:
The 12-volt DC power receptacle and the jumper harness required to
connect the receptacle to the hood wiring harness can be purchased
from your POLARIS dealer.
12-Volt RCA Power Sources
Some rider accessories require the use of an RCA power adapter. If your
model is not equipped with an RCA power plug on the handlebar cover,
an accessory 12-volt RCA adapter or RCA power plug can be purchased
from your POLARIS dealer.
12-Volt RCA Adapter
The RCA adapter can be used if your
model is equipped with the 12-volt
DC power receptacle. Plug the
adapter into the receptacle to convert
it to a 12-volt RCA power outlet.
12-Volt RCA Power Plug
The RCA power plug
(with cover) mounts to
the handlebar cover and
is plugged into the main
vehicle wire harness.
Installation instructions are provided with the accessory.
This power point is powered by the load shed relay and is not fuse
protected. POLARIS recommends using this power point for electric
helmet shields.
12-Volt Receptacle (if equipped)
12-Volt RCA Adapter
RCA Power Plug with Cover
121
MAINTENANCE
Lights
The headlight and taillight assemblies feature LED elements and are not
serviceable. If an LED fails to illuminate in either the headlight or
taillight, the entire assembly must be replaced. Please see your
POLARIS dealer.
Fuse Replacement
The brake system and ACC 2-amp fuses are located in the protective
bag above the clutch cover.
NOTICE:
Always replace a blown fuse with a new fuse having the same
amperage rating of the blown fuse. Never replace a fuse with a fuse of
a higher amperage rating.
Constant Power Fuse
Models equipped with electric start have a battery/electric start wire
harness. The 2 amp constant power fuse is located in the electric start
wiring harness.
This fuse protects KEY ON power at the ignition switch. KEY ON
power supplies battery voltage to the IDD and GPS puck.
If the IDD does not turn on when the key is in the ON position, check
for a blown fuse. If the fuse is blown, inspect the constant power circuit.
Repair or replace any damaged components before replacing the fuse.
137
MAINTENANCE
Battery (if equipped)
Battery Installation
IMPORTANT:
Route the
BROWN harness ground
wires (A) and BLACK main
battery ground cable (B) as
shown in the image. Both are
routed up and over the
rubber strap. If the ground
wires/cable are routed down
the side of the battery, they
may interfere with the rear
side panel tab. Note the
routing of the RED (positive)
battery cable (C) and that
the right fender (D) is pulled away from the chassis. Item (E) is the
constant power fuse connector.
7.
Verify that cables are properly routed.
NOTICE:
Ensure that the battery wires are routed in such a way that they
cannot come into contact with the brake disc.
8.
Secure the right fender using the plastic rivet.
9.
Reinstall the console using the two plastic rivets.
10.
Reinstall the side panel.
157
WARRANTY
Warranty Coverage and Exclusions
Limitations of Warranties and Remedies
This POLARIS Limited Warranty excludes any failures that are not caused by a defect
in material or workmanship. THIS WARRANTY DOES NOT COVER CLAIMS OF
DEFECTIVE DESIGN. This warranty also does not cover acts of God, accidental
damage, normal wear and tear, abuse or improper handling. This warranty also does not
cover any vehicle, component or part that has been altered structurally, modified,
neglected, improperly maintained or used for racing, competition or purposes other than
for which it was designed.
This warranty also excludes failures resulting from improper lubrication; improper
engine timing; improper fuel; surface imperfections caused by external stress, heat, cold
or contamination; operator error or abuse; improper component alignment, tension,
adjustment or altitude compensation; failure due to snow, water, dirt or other foreign
substance ingestion/contamination; improper maintenance; modified components; use
of aftermarket components; unauthorized repairs; repairs made after the warranty period
expires or by an unauthorized repair center; use of the product in competition or for
commercial purposes. Warranty will not apply to any product which has been damaged
by abuse, accident, fire or any other casualty not determined a defect of materials or
workmanship.
This warranty excludes damages or failures caused by abuse, accident, fire or any other
cause other than a defect in materials or workmanship and provides no coverage for
consumable components, general wear items or any parts exposed to friction surfaces,
stresses, environmental conditions and/or contamination for which they were not
designed or not intended, including but not limited to the following items:
Skis
Ski wear rods
Tracks
Slide rails
Suspension components
Finished and unfinished surfaces
Brake components
Carburetor/Throttle body components
Seat components
Engine components
Clutches and components
Drive belts
Steering components
Hydraulic components
Batteries
Circuit breakers/Fuses
Light bulbs/Sealed beam lamps
Electronic components
Idler wheels
Spark Plugs
Sealants
Lubricants
Coolant
Filters
Fuel