Polaris SCOUT SIXTY - 2016 Fuse Box Diagram

Polaris SCOUT SIXTY - 2016 Fuse Box Diagram

90
Maintenance
Battery
The motorcycle battery is a sealed, maintenance-free
battery. Do not remove the battery cap strip for any reason.
Keep the battery connections clean and tight at all times.
Battery electrolyte is poisonous. It contains sulfuric acid. Serious
burns can result from contact with skin, eyes or clothing.
Antidote:
External: Flush with water.
Internal: Drink large quantities of water or milk. Follow with milk of
magnesia, beaten egg, or vegetable oil. Call physician immediately.
Eyes: Flush with water for 15 minutes and get prompt medical
attention.
Batteries may produce explosive gases.
Keep sparks, flame, cigarettes, etc. away.
Ventilate when charging or using in an enclosed space.
Always shield eyes when working near batteries
KEEP OUT OF REACH OF CHILDREN.
Battery Removal
1.
Remove the seat. See page 86.
WARNING!
Improperly connecting or disconnecting battery
cables can result in an explosion and cause serious injury or death.
When removing the battery, always disconnect the negative (black)
cable first. When reinstalling the battery, always connect the negative
(black) cable last.
2.
Remove the fuse box from
the frame of the
motorcycle. Use care to
avoid pulling or
stretching wires. See
page 92. Fold the wires to
the right rear side of the
motorcycle.
3.
Remove the battery hold-
down strap.
Tool:
10 mm wrench
4.
Remove the negative (-) battery cable from the battery
terminal. Position the cable well clear of the terminal.
Tool:
10 mm wrench
5.
Remove the rubber cover from the positive (+) battery
cable and remove the cable from the terminal. Position
the cable well clear of the terminal.
6.
Tilt the battery slightly rearward, then lift it away from
the motorcycle.
WARNING
Negative (-)
Positive (+)
92
Maintenance
Fuse Replacement
The standard fuse box is located under the seat. This fuse
box houses all standard service fuses and the automatic
circuit breakers. Fuse application and size are provided on
a label on the fuse box cover.
The main vehicle fuse is located
on the wiring harness at the rear
of the battery. Remove the fuse
cap to inspect or replace this
fuse.
NOTICE:
Use fuses with the
recommended amperage
to avoid damage to the
electrical system.
1.
Remove the seat. See
page 86.
2.
Press the fuse box release
tab inward and slide the
fuse box rearward to
remove it from the
bracket. Use care to avoid
pulling or stretching the
wires.
3.
Bend the cover clips
slightly away from the
cover to remove the cover.
Tip:
Use the fuse puller provided
in the tool kit to remove a
fuse.
4.
After replacing a fuse, reinstall the fuse box cover.
5.
Reinstall the fuse box to the bracket. Make sure the
release tab engages.
6.
Reinstall the seat.
Main Vehicle
Fuse
Cover
Clips
Box Release
Tab
93
Maintenance
Electrical Precautions
Be aware of the following precautions regarding the
electrical system to avoid disruption of electrical signals
and possible system malfunction.
DO use ONLY genuine INDIAN MOTORCYCLE parts and
accessories designed for your model, and follow the
instructions provided.
DO use the accessory power jack provided (if equipped).
If it is necessary to provide power to an item that does not
use one of the previously mentioned power jacks, connect
to the “hot” side of the starter solenoid with an inline fuse,
and connect the ground wire to the chassis ground
located at the left rear section of the frame under the seat.
DO NOT splice or cut any wires.
DO NOT tap in to any power or ground on the motorcycle
unless specifically directed to do so by the INDIAN
MOTORCYCLE instructions that come with the kit.
DO NOT back-probe electrical connectors on the vehicle
unless directed to do so by the
INDIAN MOTORCYCLE
Service Manual
.
DO NOT power any accessories from the diagnostic
connector.
98
Maintenance
Anti-Lock Brake Light Remains Illuminated or Illuminates Intermittently
Possible Cause
Possible Remedy/Action
Blown fuse
Check the fuses. See page 92.
Loose or damaged pulse ring
Inspect pulse ring for looseness or chipped teeth.
Debris lodged in components
Inspect wheel speed sensor and pulse ring for debris.
Damage caused by debris
Inspect wheel speed sensor for cracked housing.
Damaged components
See service manual or authorized dealer.
117
Warranty
INDIAN MOTORCYCLE Warranty Policy
WARRANTY COVERAGE AND EXCLUSIONS:
LIMITATIONS OF WARRANTIES AND REMEDIES
This INDIAN MOTORCYCLE limited warranty excludes any failures that are not caused by a defect in material or workmanship. THIS
WARRANTY DOES NOT COVER CLAIMS OF DEFECTIVE DESIGN. This warranty also does not cover acts of God, accidental damage,
normal wear and tear, abuse or improper handling. This warranty also does not cover any motorcycle, component, or part that has been
altered structurally, modified, neglected, improperly maintained, or used for purposes other than for which it was designed.
This warranty excludes damages or failures resulting from: improper lubrication; improper engine timing; improper fuel; surface
imperfections caused by external stress, heat, cold or contamination; operator error or abuse; improper component alignment, tension,
adjustment or altitude compensation; snow, water, dirt or other foreign substance ingestion/contamination; improper maintenance;
modified components; use of aftermarket or unapproved components, accessories, or attachments; unauthorized repairs; or repairs made
after the warranty period expires or by an unauthorized repair center.
This warranty excludes damages or failures caused by abuse, accident, fire, or any other cause other than a defect in materials or
workmanship and provides no coverage for consumable components, general wear items, or any parts exposed to friction surfaces,
stresses, environmental conditions and/or contamination for which they were not designed or not intended, including but not limited to the
following items:
Wheels and tires
Filters
Fuel Injectors/Throttle body components
Suspension components
Lubricants
Engine components
Brake components
Bushings
Drive belts
Seat components
Sealants
Hydraulic components and fluids
Clutches and components
Coolants
Circuit breakers/Fuses
Steering components
Bearings
Electronic components
Batteries
Finished and unfinished surfaces
Spark plugs
Light bulbs/Sealed beam lamps