Nissan Armada - 2017 Fuse Box Diagram

Nissan Armada - 2017 Fuse Box Diagram

0-8
Illustrated table of contents
JVC0957X
1.
Side ventilator (P.4-51)
2.
Meters and gauges (P.2-5)
3.
Center ventilator (P.4-51)
4.
Center multi-function control panel (P.4-4)
— Vehicle information and setting buttons
(P.4-8)
— Clock (P.4-13)
5.
Center display
— Around View
¡
Monitor (if so equipped)
(P.4-29)
— RearView Monitor (if so equipped) (P.4-21)
— Navigation system*
— DVD player operation (P.4-74)
6.
Hazard warning flasher switch (P.6-2)
7.
Defroster switch (P.2-36)/Deicer switch (if so
equipped) (P.2-36)
8.
Front passenger supplemental air bag (P.1-52)
9.
Fuse box (P.8-20)
10.
Parking brake (P.5-22)
11.
Hood release handle (P.3-21)
12.
Steering wheel
— Horn (P.2-43)
— Driver supplemental air bag (P.1-52)
— Power steering (P.5-135)
13.
Push-button ignition switch (P.5-12)
14.
Climate controlled seat switch (if so equipped)
(P.2-45)/Heated seat switch (if so equipped)
(P.2-43)
15.
Heated steering wheel switch (if so equipped)
(P.2-42)
16.
Power outlet (P.2-48)
17.
Front passenger air bag status light (P.1-60)
18.
Cup holder (P.2-50)
19.
Heater and air conditioner (P.4-52)
20.
Audio system (P.4-59)
21.
Glove box (P.2-53)
*:
Refer
to
the
separate
Navigation
System
Owner’s Manual.
INSTRUMENT PANEL
0-10
Illustrated table of contents
JVC0965X
VK56VD ENGINE
1.
Window washer fluid reservoir (P.8-10)
2.
Fuse/fusible link holder (P.8-18)
3.
Engine oil dipstick (P.8-6)
4.
Power steering fluid reservoir (P.8-8)
5.
Engine oil filler cap (P.8-6)
6.
Brake fluid reservoir (P.8-9)
7.
Fuse/fusible link holder (P.8-18)
8.
Battery (P.8-11)
9.
Radiator filler cap (P.8-4)
10.
Engine coolant reservoir (P.8-4)
11.
Drive belts (P.8-13)
12.
Air cleaner (P.8-15)
ENGINE COMPARTMENT
2-4
Instruments and controls
JVC0957X
1.
Side ventilator
2.
Meters and gauges
3.
Center ventilator
4.
Center multi-function control panel
— Vehicle information and setting buttons
— Clock
5.
Center display
— Around View
¡
Monitor (if so equipped)
— RearView Monitor (if so equipped)
— Navigation system*
— DVD player operation
6.
Hazard warning flasher switch
7.
Defroster switch/Deicer switch (if so equipped)
8.
Front passenger supplemental air bag
9.
Fuse box
10.
Parking brake
11.
Hood release handle
12.
Steering wheel
— Horn
— Driver supplemental air bag
— Power steering
13.
Push-button ignition switch
14.
Climate controlled seat switch (if so equipped)/
Heated seat switch (if so equipped)
15.
Heated steering wheel switch (if so equipped)
16.
Power outlet
17.
Front passenger air bag status light
18.
Cup holder
19.
Heater and air conditioner
20.
Audio system
21.
Glove box
*:
Refer
to
the
separate
Navigation
System
Owner’s Manual.
INSTRUMENT PANEL
2-16
Instruments and controls
and all tires are properly inflated, it
is
recommended
you
consult
a
NISSAN dealer.
.
Since the spare tire is not equipped
with the TPMS, when a spare tire is
mounted or a wheel is replaced, the
TPMS will not function and the low
tire pressure warning light will flash
for
approximately
1
minute.
The
light will remain on after 1 minute.
Have
your
tires
replaced
and/or
TPMS
system
reset
as
soon
as
possible.
It
is
recommended
you
visit
a
NISSAN
dealer
for
these
services.
.
Replacing tires with those not ori-
ginally specified by NISSAN could
affect the proper operation of the
TPMS.
CAUTION
.
The TPMS is not a substitute for the
regular tire pressure check. Be sure
to check the tire pressure regularly.
.
If
the
vehicle
is
being
driven
at
speeds
of less than 16
MPH (25
km/h), the TPMS may not operate
correctly.
.
Be sure to install the specified size
of tires to the four wheels correctly.
Master warning light
When the ignition switch is in the ON position,
the master warning light illuminates if any of the
following are displayed on the vehicle informa-
tion display:
.
No key warning
.
Low fuel warning
.
Low washer fluid warning
.
Parking brake release warning
.
Door/liftgate open warning
.
Front
radar
obstruction
warning
(if
so
equipped)
.
Headlight warning
.
Loose fuel cap warning
.
Check tire pressure warning
.
Back-up
Collision
Intervention
(BCI)
not
available warning (if so equipped)
.
Back-up Collision Intervention (BCI) mal-
function warning (if so equipped)
.
Forward Emergency Braking (FEB) system
warning (if so equipped)
.
Extended
storage
fuse
warning
(if
so
equipped)
See “Vehicle information display” (P.2-20).
Seat belt warning light and chime
The light and chime remind you to fasten seat
belts. The light illuminates whenever the ignition
switch is placed in the ON position, and will
remain illuminated until the driver’s seat belt is
fastened. At the same time, the chime will sound
for about 6 seconds unless the driver’s seat belt
is securely fastened.
The
seat
belt
warning
light
for
the
front
passenger will illuminate if the seat belt is not
fastened when the front passenger’s seat is
occupied. For approximately 5 seconds after the
ignition switch is placed in the ON position, the
system does not activate the warning light for
the front passenger.
See “Seat belts” (P.1-18) for precautions on
seat belt usage.
Supplemental air bag warning light
After
placing
the
ignition
switch
in
the
ON
position, the supplemental air bag warning light
will illuminate. The supplemental air bag warning
light will turn off after about 7 seconds if the air
bag and/or pretensioner systems are opera-
tional.
2-24
Instruments and controls
8. Parking brake release warning
This warning appears when the vehicle speed is
above 4 MPH (7 km/h) and the parking brake is
applied.
9. Low fuel warning
This warning appears when the fuel level in the
tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches the 0 (Empty) position.
There is a small reserve of fuel remaining
in the tank when the fuel gauge reaches
the 0 (Empty) position.
10. Low washer fluid warning
This warning appears when the washer tank fluid
is at a low level. Add washer fluid as necessary.
(See “Window washer fluid” (P.8-10).)
11. Door/liftgate open warning (ignition
switch is in the ON position)
This warning appears if any of the doors and/or
the liftgate are open or not closed securely. The
vehicle icon indicates which door or the liftgate
is open on the display.
12. Loose fuel cap warning
This warning appears when the fuel-filler cap is
not tightened correctly after the vehicle has
been refueled. (See “Fuel-filler cap” (P.3-27).)
13. Check tire pressure warning
This warning appears when the low tire pressure
warning light in the meter illuminates and low tire
pressure is detected. The warning appears each
time the ignition switch is placed in the ON
position as long as the low tire pressure warning
light remains illuminated. If this warning appears,
stop the vehicle and adjust the tire pressure to
the recommended COLD tire pressure shown
on the Tire and Loading Information label. (See
“Low tire pressure warning light” (P.2-15) and
“Tire Pressure Monitoring System (TPMS)” (P.5-
5).)
14. Extended storage fuse warning (if so
equipped)
This warning may appear if the extended storage
fuse switch is not pushed in (switched on).
When this warning appears, push in (switch on)
the extended storage fuse switch to turn off the
warning. For more information, see “Extended
storage fuse switch” (P.8-21).
15. Back-up Collision Intervention (BCI)
not available warning (if so equipped)
This warning appears when the Back-up Colli-
sion Intervention (BCI) system is temporarily not
available.
For more details, see “Back-up Collision Inter-
vention (BCI)” (P.5-56).
16. Back-up Collision Intervention (BCI)
malfunction warning (if so equipped)
This warning appears when the Back-up Colli-
sion Intervention (BCI) system is not functioning
properly.
For more details, see “Back-up Collision Inter-
vention (BCI)” (P.5-56).
17. Headlight warning
This warning appears if the LED headlights are
malfunctioning. It is recommended you have the
system checked by a NISSAN dealer.
18. Front radar obstruction warning (if so
equipped)
This warning appears when the sensor area of
the front bumper is covered with dirt or is
obstructed, making it impossible to detect a
vehicle ahead.
The
following
systems
will
be
automatically
canceled.
SIC4456
Back side of front console
SIC4391
Luggage room
Type A (if so equipped)
The power outlet is used for powering electrical
accessories such as cellular telephones.
CAUTION
.
The
outlet
and
plug
may
be
hot
during or immediately after use.
.
Do not use with accessories that
exceed a combined power draw of
12
volts,
120W
(10A)
for
all
the
power outlets. Do not use double
adapters or more than one electrical
accessory.
.
This power outlet is not designed
for use with a cigarette lighter unit.
.
Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal tem-
perature fuse may blow.
SIC2648
Main switch
Type B (if so equipped)
The power outlet (plug type) is located on the
back side of the front console. It can operate
when the ignition switch in the ON position and
the main switch (located in the console box) is
ON.
The specification of this power outlet is for
use of a 120 volt, 150W (1.25A) power draw.
To turn on or off the power supply to the outlet,
push the ON
*
1
or OFF
*
2
side of the main
switch. When the switch is turned to the ON
position, the indicator light
*
A
will illuminate.
Instruments and controls
2-49
3-34
Pre-driving checks and adjustments
LOCK position.
The driver’s seat and steering wheel will return
to
the
previous
positions
when
the
ignition
switch is pushed to the ACC position.
The driver’s seat will not return to the previous
positions if the seat or steering adjusting switch
is operated when the seat is at the exit position.
Cancel or activate entry/exit function
The shift lever must be in the P (Park) position
with the ignition switch in the OFF position.
The
entry/exit
function
can
be
activated
or
canceled
by
pressing
and
holding
the
SET
switch for more than 10 seconds.
The entry/exit function can also be activated or
canceled if the “Lift Steering Wheel on Exit” key
or “Slide Driver Seat Back on Exit” key is turned
to ON or OFF in the “Comfort” settings. (See
“How to use SETTING button” (P.4-13).)
Initialize entry/exit function
If the battery cable is disconnected, or if the fuse
opens,
the
entry/exit
function
will
not
work
though this function was set on before. In such
a case, after connecting the battery or replacing
with a new fuse, open and close the driver’s
door more than two times after the ignition
switch is turned from the ON position to the
LOCK position. The entry/exit function will be
activated.
MEMORY STORAGE
Two
positions
for
the
driver’s
seat,
steering
column and outside mirrors can be stored in the
automatic drive positioner memory. Follow these
procedures to use the memory system.
1.
Move the shift lever to the P (Park) position.
2.
Adjust the driver’s seat, steering column and
outside mirrors to the desired positions by
manually operating each adjusting switch.
For additional information, see “Seats” (P.1-
2) and “Tilt/telescopic
steering”
(P.3-29)
and “Outside mirrors” (P.3-31).
3.
Push the SET switch and, within 5 seconds,
push the memory switch (1 or 2) fully for at
least 1 second.
The indicator light for the pushed memory
switch
will
stay
on
for
approximately
5
seconds after pushing the switch.
When the memory is stored in the memory
switch (1 or 2), a buzzer will sound.
If memory is stored in the same memory
switch, the previous memory will be deleted.
Linking Intelligent Key to a stored mem-
ory position
The Intelligent Key can be linked to a stored
memory position with the following procedure.
1.
Follow
the
steps
for
storing
a
memory
position.
2.
While the indicator light for the memory
switch being set is illuminated for 5 sec-
onds, push the
button on the Intelligent
Key. If the indicator light blinks, the Intelli-
gent Key is linked to that memory setting.
Push the ignition switch to the OFF position, and
then push the
button on the Intelligent Key.
The driver’s seat, steering wheel and outside
mirrors will move to the memorized position.
Confirming memory storage
.
Push the ignition switch to the ON position
and
push
the
SET switch.
If
the
main
memory has not been stored, the indicator
light will
come on for approximately 0.5
second. When the memory has stored in
position, the indicator light will stay on for
approximately 5 seconds.
.
If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using
the previous procedure.
4-72
Monitor, heater, air conditioner, audio, phone and voice recognition systems
tions.
.
NO SIGNAL (No signal is received while the
SAT tuner is connected.)
.
OFF AIR (Broadcasting signed off)
.
CHECK
ANTENNA
(Antenna
connection
error)
.
LOADING
(When
the
initial
setting
is
performed)
.
UPDATING (When the satellite radio sub-
scription is not active)
.
INVALID CH (Invalid channel is received.)
SCAN tuning:
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broad-
casting station/channel for 5 seconds. Pushing
the button again during this 10 seconds period
will stop SCAN tuning and the radio will remain
tuned to that station/channel.
If the SCAN tuning button is not pushed within 5
seconds,
SCAN
tuning
moves
to
the
next
station/channel.
*
1
to
*
6
Station memory operations:
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2), 18 for SiriusXM
Satellite Radio (6 each for XM1, XM2 and XM3)
and 6 stations can be set for the AM band.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station/channel using
the SEEK·CAT, TRACK, SCAN button or the
radio TUNE knob.
3.
Push and hold the desired station preset
button
*
1
to
*
6
until the radio mutes.
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations/channels.
Menu (SiriusXM Satellite Radio):
When the “Menu” key on the display is selected
while
the
SiriusXM
Satellite
Radio
is
being
played, the menu list will be displayed.
The following items are available.
.
Preset List
Displays the preset channel list. If 1 of the 6
preset stations listed is touched and held,
the current station will be stored as the new
preset.
.
Customize Channel List
Selects specific channels to skip while using
the TUNE, SEEK·CAT or Menu-Categories
feature.
.
Favorite Artists & Songs
Stores the current artist or song that is being
played. Touch the “Alert” key to be reminded
when the stored artist or song is playing on a
station while listening to SiriusXM Satellite
Radio.
.
Categories
Selecting a category will go to the first
channel
in
that
category
as
defined
by
SiriusXM Satellite Radio.
.
Direct Tune
Inputs
the
channel
number
by
using
a
keypad.
Compact Disc (CD) player operation
Push the ignition switch to the ACC or ON
position and insert the Compact Disc (CD) into
the slot with the label side facing up. The CD will
be guided automatically into the slot and start
playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If the radio is already operating, it will auto-
matically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the ON·OFF button will
difficulties or excessive emissions, and could
affect
your
warranty
coverage.
If
in
doubt
about any servicing, it is recommended
you have it done by a NISSAN dealer.
JVC0965X
VK56VD ENGINE
1.
Window washer fluid reservoir
2.
Fuse/fusible link holder
3.
Engine oil dipstick
4.
Power steering fluid reservoir
5.
Engine oil filler cap
6.
Brake fluid reservoir
7.
Fuse/fusible link holder
8.
Battery
9.
Radiator filler cap
10.
Engine coolant reservoir
11.
Drive belts
12.
Air cleaner
Do-it-yourself
8-3
ENGINE COMPARTMENT CHECK
LOCATIONS
ENGINE COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch is pushed to the
OFF or LOCK position and the headlight
switch is turned to OFF.
2.
Open
the
engine
hood
and
remove
the
cover on the battery.
3.
Remove the fuse/fusible link holder cover
*
1
,
*
2
or
*
3
.
4.
Remove the fuse with the fuse puller.
SDI1753
Type A (if so equipped)
SDI1754
Type B (if so equipped)
5.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
. Spare fuses are stored in the
passenger compartment fuse box.
6.
If a new fuse also opens, have the electrical
system checked and repaired. It is recom-
mended you visit a NISSAN dealer for this
service.
Fusible links
If any electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace only with genuine NISSAN parts.
Do-it-yourself
8-19
8-20
Do-it-yourself
JVM0200X
PASSENGER COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch is pushed to the
OFF or LOCK position and the headlight
switch is turned to OFF.
2.
Open the fuse box lid.
3.
Remove the fuse with the fuse puller
*
A
.
SDI1754
4.
If the fuse is open, replace it with a new fuse.
5.
If a new fuse also opens, have the electrical
system checked and repaired. It is recom-
mended you visit a NISSAN dealer for this
service. Spare fuses are stored in the fuse
box.
SDI2704
Extended storage fuse switch (if so
equipped)
To reduce battery drain, the extended storage
fuse switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If
the
extended
storage
fuse
switch
is
not
pushed in (switched on), the “SHIPPING MODE
ON,
PUSH
STORAGE
FUSE
warning
may
appear on the vehicle information display (if so
equipped).
See
“Vehicle
information
display”
(P.2-20).
If any electrical equipment does not operate,
remove the extended storage fuse switch and
check for an open fuse.
NOTE:
If the extended storage fuse switch mal-
functions or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
1.
To remove the extended storage fuse switch,
be sure the ignition switch is in the OFF or
LOCK position.
2.
Be sure the headlight switch is in the OFF
position.
3.
Remove the fuse box cover.
4.
Pinch the locking tabs
*
1
found on each
side of the storage fuse switch.
5.
Pull the storage fuse switch straight out from
the fuse box
*
2
.
CAUTION
Be
careful
not
to
allow
children
to
swallow the battery and removed parts.
Do-it-yourself
8-21
INTELLIGENT KEY BATTERY
REPLACEMENT