Nissan 370Z - 2012 Fuse Box Diagram

Nissan 370Z - 2012 Fuse Box Diagram

SSI0653
1.
Ventilator (P.4-24)
2.
Center display and multi-function control panel (if
so equipped) (P.4-3) or Instrument pocket (if so
equipped) (P.2-40)
— Navigation system* (if so equipped)
— Vehicle information and setting buttons (if so
equipped) (P.4-7)
— Bluetooth
®
Hands-Free Phone System (if so
equipped) (P.4-81, P.4-92, P.4-104)
3.
Front passenger air bag status light (P.1-33)
4.
Front passenger supplemental air bag (P.1-28)
5.
Fuse box cover (P.8-22)
6.
Push-button ignition switch (P.5-8)
7.
Hazard warning flasher switch (P.2-35)
8.
Seat heater switch (if so equipped) (P.2-36) or
Climate controlled seat switch (if so equipped)
(P.2-38)
9.
Soft top operating switch (for Roadster models)
(P.3-21)
10. SynchroRev Match mode (S-MODE) switch (if so
equipped) (P.5-17)
11. Heater and air conditioner (P.4-24)
— Rear window defroster switch (P.2-31)
12. Audio system (P.4-31)
13. Power outlet (P.2-39)
14. Glove box (P.2-41)
*:
Refer
to
the
separate
Navigation
System
Owner’s Manual.
Illustrated table of contents
0-11
INSTRUMENT PANEL
JVM0086X
VQ37VHR ENGINE MODEL
1.
Fuse/fusible link holder (P.8-22)
2.
Battery (P.8-16)
3.
Radiator filler cap (P.8-9)
4.
Engine oil dipstick (P.8-11)
5.
Engine oil filler cap (P.8-11)
6.
Brake fluid reservoir (P.8-14)
7.
Clutch fluid reservoir (Manual Transmission mod-
els) (P.8-14)
8.
Power steering fluid reservoir (P.8-13)
9.
Window washer fluid reservoir (P.8-15)
10. Air cleaner (P.8-19)
11. Drive belt location (P.8-18)
12. Engine coolant reservoir (P.8-9)
Illustrated table of contents
0-13
ENGINE COMPARTMENT
2-4
Instruments and controls
SSI0653
1.
Ventilator (P.4-24)
2.
Center display and multi-function control panel (if
so equipped) (P.4-3) or Instrument pocket (if so
equipped) (P.2-40)
— Navigation system* (if so equipped)
— Vehicle information and setting buttons (if so
equipped) (P.4-7)
— Bluetooth
®
Hands-Free Phone System (if so
equipped) (P.4-81, P.4-104)
3.
Front passenger air bag status light (P.1-33)
4.
Front passenger supplemental air bag (P.1-28)
5.
Fuse box cover (P.8-22)
6.
Push-button ignition switch (P.5-8)
7.
Hazard warning flasher switch (P.2-35)
8.
Seat heater switch (if so equipped) (P.2-36) or
Climate controlled seat switch (if so equipped)
(P.2-38)
9.
Soft top operating switch (for Roadster models)
(P.3-21)
10. SynchroRev Match mode (S-MODE) switch (if so
equipped) (P.5-17)
11. Heater and air conditioner (P.4-24)
— Rear window defroster switch (P.2-31)
12. Audio system (P.4-31)
13. Power outlet (P.2-39)
14. Glove box (P.2-41)
*:
Refer
to
the
separate
Navigation
System
Owner’s Manual.
INSTRUMENT PANEL
SSD1161
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor.
If maximum engine power is needed to free a
stuck vehicle, turn the VDC system off.
To turn off the VDC system, push the VDC OFF
switch. The
indicator will illuminate.
Push the VDC OFF switch again or restart the
engine to turn on the system. (See “Vehicle
Dynamic Control (VDC) system” (P.5-28).)
SIC3984
Center console
SIC3985
Lower glove box
The power outlet is located in the center console
and on the lower glove box.
CAUTION
.
The
outlet
and
plug
may
be
hot
during or immediately after use.
.
Do not use with accessories that
exceed a 12 volt, 120W (10A) power
draw. Do not use double adapters or
more than one electrical accessory.
.
Use power outlet with the engine
running
to
avoid
discharging
the
vehicle battery.
.
Avoid using power outlet when the
air conditioner, headlights or rear
window defroster is on.
.
This power outlet is not designed
for use with a cigarette lighter unit.
.
Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal tem-
perature fuse may blow.
.
Before inserting or disconnecting a
plug, be sure the electrical acces-
sory being used is turned OFF.
Instruments and controls
2-39
VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH
POWER OUTLET
4-46
Center display, heater, air conditioner, audio, phone and voice recognition systems
SCAN tuning:
Push the SCAN tuning button to tune from low
to high frequencies and stops at each broad-
casting
station
for
5
seconds.
Pushing
the
button again during this 5 seconds period will
stop SCAN tuning and the radio will remain
tuned to that station.
If the SCAN tuning button is not pushed within 5
seconds,
SCAN
tuning
moves
to
the
next
station.
to
Station memory operations:
Twelve stations can be set for the FM band (6
each for FM1 and FM2) and 6 stations can be
set for the AM band.
1.
Choose the radio band AM, FM1 or FM2
using the radio band select button.
2.
Tune to the desired station using the SEEK,
SCAN or TUNE button.
3.
Select the desired station and push and
hold the desired station preset buttons 1 to
6 until a beep sound is heard. (The radio
mutes when the select button is pushed.)
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
blows, the radio memory will be erased. In that
case, reset the desired stations.
Compact Disc (CD) player operation
Place the ignition switch in the ACC or ON
position, and insert the CD into the slot with the
label side facing up. The CD will be guided
automatically into the slot and start playing.
After loading the disc, the number of tracks on
the disc will appear on the display.
If the radio is already operating, it will auto-
matically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the PWR button will start
the CD.
MP3 or WMA CDs are not supported with this
CD player. If an MP3 or WMA CD is inserted
into the slot, the counter on the audio display
automatically advances without sound. However
this is a specification of the CD mechanism and
not a malfunction.
Do not use 3.1 in (8 cm) discs.
CD PLAY:
When the CD button is pushed with the system
off and the CD loaded, the system will turn on
and the CD will start to play.
When the CD button is pushed with the CD
loaded and the radio playing, the radio will
automatically be turned off and the CD will start
to play.
FF (Fast Forward), REW (Rewind):
When the
or
of the TUNE button is
pushed while the CD is being played, the CD
will play while fast forwarding or rewinding.
When the button is released, the CD will return
to normal play speed.
APS (Automatic Program Search) FF,
APS REW:
When the
of the SEEK button is pushed
while the CD is being played, the next track or
the current track on the CD will start to play from
its beginning. Push several times to skip through
tracks. The CD will advance the number of times
the button is pushed. (When the last track on
the CD is skipped through, the first track will be
played.)
When the
button is pushed, the track being
played returns to its beginning. Push several
times to skip back through tracks. The CD will
go back the number of times the button is
pushed.
4-50
Center display, heater, air conditioner, audio, phone and voice recognition systems
notices will be displayed under certain condi-
tions.
.
NO SIGNAL (No signal is received while the
SAT tuner is connected.)
.
OFF AIR (Broadcasting signed off)
.
CHECK
ANTENNA
(Antenna
connection
error)
.
LOADING
(When
the
initial
setting
is
performed)
.
UPDATING (When the satellite radio sub-
scription is not active)
SCAN tuning:
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broad-
casting station/channel for 5 seconds. Pushing
the button again during this 5 seconds period
will stop SCAN tuning and the radio will remain
tuned to that station/channel.
If the SCAN tuning button is not pushed within 5
seconds,
SCAN
tuning
moves
to
the
next
station/channel.
*
1
to
*
6
Station memory operations:
18 stations/channels can be set for the SAT
band (6 each for XM1, XM2 and XM3), 12 can
be set for the FM band (6 each for FM1 and
FM2), and 6 can be set for the AM band.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station/channel using
the SEEK, SCAN or TUNE button.
3.
Push and hold the desired radio station
preset button
*
1
to
*
6
until a beep sound
is heard. (The radio mutes when the select
button is pushed.)
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations.
RADIO DISPLAY change:
When the DISP button is pushed while the radio
is being played, the audio display will change as
follows:
Compact Disc (CD) changer operation
Push the ignition switch to the ACC or ON
position, push the LOAD button and insert the
CD into the slot with the label side facing up.
The CD will be guided automatically into the slot
and start playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If the radio is already operating, it will auto-
matically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the ON·OFF button will
start the CD.
CD LOAD:
To insert a CD in the CD changer, push the
LOAD button for less than 1.5 seconds. Select
the loading position by pushing the CD insert
select button
*
1
to
*
6
, then insert the CD.
To
insert
6
CDs
to
the
CD
changer
in
succession, push the LOAD button for more
than 1.5 seconds.
The inserted slot numbers will illuminate on the
display.
.
UPDATING (When the satellite radio sub-
scription is not active)
SCAN tuning:
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broad-
casting station/channel for 5 seconds. Pushing
the button again during this 5 seconds period
will stop SCAN tuning and the radio will remain
tuned to that station/channel.
If the SCAN tuning button is not pushed within 5
seconds,
SCAN
tuning
moves
to
the
next
station/channel.
*
1
to
*
6
Station memory operations:
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2), 18 for XM radio (6
each for XM1, XM2 and XM3) and 6 stations
can be set for the AM band.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station/channel using
the
SEEK/TRACK,
SCAN
button
or
the
radio TUNE knob.
3.
Push and hold the desired station preset
button
*
1
to
*
6
until the radio mutes.
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations/channels.
List (AM and FM radio):
When the “List” key on the display is selected
while the FM or AM radio is being played, the
preset station list will be displayed.
If 1 of the 6 preset stations listed is touched and
held, the current station will be stored as the
new preset.
Menu (XM Satellite Radio):
When the “Menu” key on the display is selected
while the XM Satellite Radio is being played, the
menu list will be displayed.
The following items are available.
.
Preset List
Displays the preset channel list. If 1 of the 6
preset stations listed is touched and held,
the current station will be stored as the new
preset.
.
Customize Channel List
Selects specific channels to skip while using
the
TUNE,
SEEK/CATEGORY or
Menu-
Categories feature.
.
Favorite Artists & Songs
Stores the current artist or song that is being
played. Touch the “Alert” key to be reminded
when the stored artist or song is playing on a
station while listening to XM.
.
Categories
Selecting a category will go to the first
channel in that category as defined by XM
Radio.
.
Direct Tune
Inputs
the
channel
number
by
using
a
keypad.
Compact Disc (CD) player operation
Push the ignition switch to the ACC or ON
position and insert the Compact Disc (CD) into
the slot with the label side facing up. The CD will
be guided automatically into the slot and start
playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If the radio is already operating, it will auto-
matically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the ON·OFF button will
start the CD.
Do not use 3.1 in (8 cm) discs.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-55
8-8
Maintenance and do-it-yourself
JVM0086X
VQ37VHR ENGINE MODEL
1.
Fuse/fusible link holder
2.
Battery
3.
Radiator filler cap
4.
Engine oil dipstick
5.
Engine oil filler cap
6.
Brake fluid reservoir
7.
Clutch fluid reservoir (Manual Transmission mod-
els)
8.
Power steering fluid reservoir
9.
Window washer fluid reservoir
10 Air cleaner
11. Drive belt location
12. Engine coolant reservoir
ENGINE COMPARTMENT CHECK
LOCATIONS
8-22
Maintenance and do-it-yourself
If the brakes do not operate properly, have the
brakes checked by a NISSAN dealer.
SELF-ADJUSTING BRAKES
Your
vehicle
is
equipped
with
self-adjusting
brakes.
The disc-type brakes self-adjust every time the
brake pedal is applied.
WARNING
See
a
NISSAN
dealer
for
a
brake
system check if the brake pedal height
does not return to normal.
BRAKE PAD WEAR WARNING
The disc brake pads have audible wear warn-
ings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound will
first
occur
only
when
the
brake
pedal
is
depressed. After more wear of the brake pad
the sound will always be heard even if the brake
pedal
is
not
depressed.
Have
the
brakes
checked as soon as possible if the wear warning
sound is heard.
Under
some
driving
or
climate
conditions,
occasional brake squeak, squeal or other noise
may be heard. Occasional brake noise during
light to moderate stops is normal and does not
affect the function or performance of the brake
system.
Proper brake inspection intervals should
be followed.
For additional information, see the
maintenance
log
section
of
your
“NISSAN
Service and Maintenance Guide”.
SDI1479A
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch is pushed to the
OFF or LOCK position and the headlight
switch is turned to OFF.
BRAKES
FUSES
2.
Open
the
engine
hood
and
remove
the
cover on the battery and the fuse/fusible link
holder.
3.
Remove the fuse/fusible link holder cover.
4.
Remove the fuse with the fuse puller located
in the passenger compartment fuse box.
SDI1754
5.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
. Spare fuses are stored in the
passenger compartment fuse box.
6.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
Fusible links
If any electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace only with genuine NISSAN parts.
Maintenance and do-it-yourself
8-23
8-24
Maintenance and do-it-yourself
SDI2361
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch is pushed to the
OFF or LOCK position and the headlight
switch is turned to OFF.
2.
Open the fuse box lid.
3.
Remove the fuse with the fuse puller
*
A
.
4.
If the fuse is open, replace it with a new fuse.
Spare fuses are stored in the fuse box.
5.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
SDI2704
Extended storage switch (if so equipped)
To reduce battery drain, the extended storage
switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If any electrical equipment does not operate,
remove the extended storage switch and check
for an open fuse.
NOTE:
If the extended storage switch malfunc-
tions,
or
if
the
fuse
is
open,
it
is
not
necessary to replace the switch. In this
case, remove the extended storage switch
and replace it with a new fuse of the same
rating.
How to remove the extended storage
switch:
1.
To remove the extended storage switch, be
sure the ignition switch is in the OFF or
LOCK position.
2.
Be sure the headlight switch is in the OFF
position.
3.
Remove the fuse box cover.
4.
Pinch the locking tabs
*
1
found on each
side of the storage switch.
5.
Pull the storage switch straight out from the
fuse box
*
2
.
SDI2451
CAUTION
Be
careful
not
to
allow
children
to
swallow the battery and removed parts.
Replace the battery as follows:
1.
Remove the mechanical key from the key.
2.
Insert a small screwdriver into the slit of the
corner and twist it to separate the upper part
from the lower part. Use a cloth to protect
the casing.
3.
Replace the battery with a new one.
Recommended battery:
CR2032 or equivalent
.
Do
not
touch
the
internal
circuit
and
electric
terminals
as
doing
so
could
cause a malfunction.
.
Hold the battery by the edges. Holding
the battery across the contact points will
seriously deplete the storage capacity.
.
Make sure that the
+
side faces the
bottom case.
Maintenance and do-it-yourself
8-25
INTELLIGENT KEY BATTERY
REPLACEMENT