Nissan Frontier - 2011 Fuse Box Diagram

Nissan Frontier - 2011 Fuse Box Diagram

QR25DE engine
1.
Windshield-washer fluid
reservoir (P. 8-15)
2.
Fuse/fusible link box (P. 8-24)
3.
Fuse and relay box (P. 8-24)
4.
Air cleaner (P. 8-20)
5.
Engine oil filler cap (P. 8-10)
6.
Engine oil dipstick (P. 8-10)
7.
Brake fluid reservoir/Clutch fluid
reservoir (M/T model) (P. 8-14)
8.
Drive belt location (P. 8-18)
9.
Radiator cap (P. 8-8)
10.
Power steering fluid reservoir (P. 8-14)
11.
Battery (P. 8-16)
12.
Engine coolant reservoir (P. 8-8)
See the page number indicated in paren-
theses for operating details.
WDI0643
ENGINE COMPARTMENT CHECK
LOCATIONS
0-8
Illustrated table of contents
VQ40DE engine
1.
Windshield-washer fluid reservoir
(P. 8-15)
2.
Fuse/fusible link box (P. 8-24)
3.
Fuse and relay box (P. 8-24)
4.
Engine oil filler cap (P. 8-10)
5.
Engine oil dipstick (P. 8-10)
6.
Brake fluid reservoir/Clutch fluid
reservoir (M/T model) (P. 8-14)
7.
Air cleaner (P. 8-20)
8.
Drive belt location (P. 8-18)
9.
Radiator cap (P. 8-8)
10.
Power steering fluid reservoir (P. 8-14)
11.
Battery (P. 8-16)
12.
Engine coolant reservoir (P. 8-8)
See the page number indicated in paren-
theses for operating details.
LII0167
Illustrated table of contents
0-9
The power outlets are for powering electrical
accessories such as cellular telephones.
The bottom power outlet located on instrument
panel is powered directly by the vehicle’s battery.
The power outlet located inside the center con-
sole is powered only when the ignition switch is in
the ACC or ON position.
Open the cap to use a power outlet.
CAUTION
The outlet and plug may be hot during
or immediately after use.
Only certain power outlets are designed
for use with a cigarette lighter unit. Do
not use any other power outlet for an
accessory
lighter.
See
your
NISSAN
dealer for additional information.
Do not use with accessories that ex-
ceed a 12 volt, 120W (10A) power draw.
Do not use double adapters or more
than one electrical accessory.
Use power outlets with the engine run-
ning to avoid discharging the vehicle
battery.
Avoid using power outlets when the air
conditioner, headlights or rear window
defroster is on.
Before
inserting
or
disconnecting
a
plug, be sure the electrical accessory
being used is turned OFF.
Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may open.
When not in use, be sure to close the
cap. Do not allow water or any other
liquids to contact the outlet.
Front row
LIC1430
Center console
LIC0761
POWER OUTLET
Instruments and controls
2-37
The FM stereo indicator, ST, illuminates during
FM stereo reception. When the stereo broadcast
signal is weak, the radio automatically changes
from stereo to monaural reception.
TUNE buttons:
Manual tuning
Press the TUNE
or
button for less
than 0.5 seconds for manual tuning.
To move quickly through the channels, press and
hold either TUNE
or
button down
for more than 1.5 seconds.
SEEK buttons:
SEEK tuning
Press the SEEK
or
button to seek
through the frequencies. Seek tuning begins
from low to high frequencies, or high to low
frequencies,
depending
on
which
button
is
pressed, and stops at the next broadcasting sta-
tion. Once the highest broadcasting station is
reached, the radio continues in the seek mode at
the lowest broadcasting station.
Station memory operations:
18 stations can be set for the FM and AM radio to
the A, B and C preset button in any combination
of AM or FM stations.
1. Press the PRESET A·B·C button to change
between storage banks. The radio displays
the icon A, B or C to indicate which set of
presets are active.
2. Tune to the desired station using manual
TUNE or SEEK tuning. Press and hold any of
the desired station memory buttons (1 – 6)
until a beep sound is heard. (The radio mutes
when the select button is pressed.)
3. The channel indicator will then come on and
the sound will resume. Programming is now
complete.
4. Other buttons can be set in the same man-
ner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be canceled. In that
case, reset the desired stations.
Compact disc (CD) player operation
Place the ignition switch in the ACC or ON
position and carefully insert the compact disc
into the slot with the label side up. The compact
disc is automatically pulled into the slot and starts
to play.
If the radio is already operating, it automatically
turns off and the compact disc begins to play.
CD button:
When the CD button is pressed with a compact
disc loaded and the radio playing, the radio turns
off and the last used compact disc starts to play.
TUNE (rewind and fast
forward) buttons:
When
the
TUNE
or
button
is
pressed while the compact disc is playing, the
compact disc plays at an increased speed while
rewinding or fast forwarding. When the button is
released, the compact disc returns to normal play
speed.
SEEK buttons:
When
is pressed while the compact disc
is playing, the next track following the present
one
starts
to
play
from
the
beginning.
Press
several times to skip several tracks.
Each time the button is pressed, the CD ad-
vances 1 additional track. The track number ap-
pears in the display window. (When the last track
on the compact disc is skipped, the first track is
played.)
When
is pressed, the track being played
returns to the beginning. Press
several
times to skip back several tracks. Each time the
button is pressed, the CD moves back one track.
Heater, air conditioner, audio and phone systems
4-27
If a compact disc is playing when the RADIO
button is pushed, the compact disc will automati-
cally be turned off and the last radio station
played will come on.
The FM stereo indicator ST will glow during FM
stereo reception. When the stereo broadcast
signal is weak, the radio will automatically change
from stereo to monaural reception.
CAT FOLDER (tuning)
button:
To
manually
tune
the
radio,
press
the
CAT
FOLDER button
or
or turn the tun-
ing knob to right or left.
To move quickly through the channels, press and
hold either the
or
button down for
more than 1.5 seconds.
SEEK/TRACK tuning
button:
Press the SEEK/TRACK button
or
for less than 1.5 seconds to tune from high to low
or low to high frequencies and stop at the next
broadcasting station.
To seek quickly through the channels, press and
hold the SEEK/TRACK button for more than 1.5
seconds. When the button is released the radio
will seek to the next broadcasting station.
SCAN RPT tuning:
Press the SCAN RPT button for more than 1.5
seconds to stop at each broadcasting station
(AM, FM or SAT if so equipped) for 5 seconds.
Pressing the button again during this 5 second
period will stop scan tuning and the radio will
remain tuned to that station. If the SCAN RPT
button is not pressed within 5 seconds, scan
tuning moves to the next station.
PRESET A·B·C (Station memory opera-
tions):
18 stations can be set for the FM, AM and SAT
(satellite, if so equipped) radio to the A, B and C
preset button in any combination of FM, AM or
SAT stations.
1. Choose preset bank A, B or C using the
PRESET A·B·C select button.
2. Select the desired FM, AM or SAT station
band.
3. Tune to the desired station using manual,
SEEK or SCAN tuning. Press and hold any
of the desired station memory buttons (1 –
6) until a beep sound is heard.
4. The channel indicator will then come on and
the sound will resume. Programming is now
complete.
5. Other buttons can be set in the same man-
ner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be canceled. In that
case, reset the desired stations.
Radio data system (RDS):
RDS stands for Radio Data System, and is a data
information service transmitted by some radio
stations on the FM band (not AM band). Cur-
rently, most RDS stations are in large cities, but
many stations are now considering broadcasting
RDS data.
RDS can display:
Station call sign, such as “WHFR 98.3”.
Station name, such as “The Groove”.
Music or programming type such as “Clas-
sical”, “Country”, or “Rock”.
Artist and song information.
If the station broadcasts RDS information, the
RDS icon is displayed.
4-32
Heater, air conditioner, audio and phone systems
QR25DE engine
1.
Windshield-washer fluid reservoir
2.
Fuse/Fusible link box
3.
Fuse and relay box
4.
Air cleaner
5.
Engine oil filler cap
6.
Engine oil dipstick
7.
Brake fluid reservoir/Clutch fluid
reservoir (M/T model)
8.
Drive belt location
9.
Radiator cap
10.
Power steering fluid reservoir
11.
Battery
12.
Engine coolant reservoir
NOTE:
Engine cover removed for clarity.
WDI0643
ENGINE COMPARTMENT CHECK
LOCATIONS
8-6
Maintenance and do-it-yourself
VQ40DE engine
1.
Windshield-washer fluid reservoir
2.
Fuse/fusible link box
3.
Fuse and relay box
4.
Engine oil filler cap
5.
Engine oil dipstick
6.
Brake fluid reservoir/Clutch fluid
reservoir (M/T model)
7.
Air cleaner
8.
Drive belt location
9.
Radiator cap
10.
Power steering fluid reservoir
11.
Battery
12.
Engine coolant reservoir
NOTE:
Engine cover removed for clarity.
LII0167
Maintenance and do-it-yourself
8-7
Two types of fuses are used. Type
²
A
is used in
the fuse boxes in the engine compartment. Type
²
B
is used in the passenger compartment fuse
box.
Type A fuses are provided as spare fuses. They
are stored in the passenger compartment fuse
box.
Type A fuses can be installed in the engine com-
partment
and
passenger
compartment
fuse
boxes.
If a type A fuse is used to replace a type B fuse,
the type A fuse will not be level with the fuse
pocket as shown in the illustration. This will not
affect the performance of the fuse. Make sure the
fuse is installed in the fuse box securely.
Type B fuses cannot be installed in the under-
hood fuse boxes. Only use type A fuses in the
underhood fuse boxes.
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not come on,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Open the engine hood.
LDI0455
LDI0457
LDI0444
FUSES
8-24
Maintenance and do-it-yourself
3. Remove the fuse box cover by pushing the
tab and lifting the cover up.
4. Remove the fuse with the fuse puller. The
fuse puller is located in the center of the fuse
block in the passenger compartment.
5. If the fuse is open
²
A
, replace it with a new
fuse
²
B
.
6. If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
Fusible links
If the electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace with only Genuine NISSAN parts.
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Pull the fuse box cover to remove.
3. Remove the fuse with the fuse puller.
WDI0452
LDI0445
Maintenance and do-it-yourself
8-25
4. If the fuse is open
²
A
, replace it with an
equivalent good fuse
²
B
.
5. Push the fuse box cover to install.
6. If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
CAUTION
Be careful not to allow children to swallow
the battery or removed parts.
Type A
WDI0452
Type B
LDI0456
BATTERY REPLACEMENT
8-26
Maintenance and do-it-yourself