Nissan Murano - 2007 Fuse Box Diagram

Nissan Murano - 2007 Fuse Box Diagram

1. Headlight, fog light* and turn signal switch
(P.2-22)
2. Trip odometer reset button (P.2-4)
3. Instrument brightness control switch
(P.2-26)
4. Meters/gauges (P.2-3)
5. Windshield (P.2-20)/rear window (P.2-21)
wiper and washer switch
6. Hazard warning flasher switch (P.2-27)
7. Center ventilator (P.4-21)
8. Audio control (P.4-27)
9. Display (P.4-2, P.4-11)/clock (P.4-4, P4-18)
10. Rear window defroster and Heated outside
mirror* switch (P.2-22)
11. Display
screen
control
(P.4-2,
P4-11)
and/or Navigation system*1
12. Passenger supplemental air bag (P.1-41)
13. Side ventilator (P.4-21)
14. Headlight aiming control switch* (P.2-25)
15. Vehicle
Dynamic
Control
(VDC)
OFF
switch* (P.2-29) or Headlight aiming con-
trol* (P.2-25)
16. Steering switch for audio control* (P.4-43)
17. Fuse box cover (P.8-21)
18. Tilting steering wheel lock lever (P.3-28)
19. Driver supplemental air bag (P.1-41)/Horn
(P.2-28)
20. Cruise control main/set switch (P.5-22)
21. Ignition switch/steering lock (P.5-9)
(P.5-10)
22. Heater/air conditioner control (P.4-23)
SSI0176
INSTRUMENT PANEL
Illustrated table of contents
0-5
1. Power steering fluid reservoir (P.8-12)
2. Engine oil filler cap (P.8-10)
3. Brake fluid reservoir (P.8-13)
4. Air cleaner (P.8-17)
5. Windshield washer fluid reservoir (P.8-14)
6. Engine coolant reservoir (P.8-8)
7. Drive belts (P.8-16)
8. Radiator filler cap (P.8-8)
9. Engine oil dipstick (P.8-9)
10. Fuse/fusible link holder (P.8-21)
11. Battery (P.8-14)
SDI1760
ENGINE COMPARTMENT CHECK
LOCATIONS
0-8
Illustrated table of contents
1. Headlight, fog light* and turn signal switch
2. Trip odometer reset button
3. Instrument brightness control switch
4. Meters/gauges
5. Windshield/rear window wiper and washer
switch
6. Hazard warning flasher switch
7. Center ventilator
8. Audio control
9. Display/clock
10. Rear window defroster and Heated outside
mirror* switch
11. Display screen control and/or Navigation
system*1
12. Passenger supplemental air bag
13. Side ventilator
14. Headlight aiming control switch*
15. Vehicle Dynamic Control (VDC) OFF
switch* or Headlight aiming control*
16. Steering switch for audio control*
17. Fuse box cover
18. Tilting steering wheel lock lever
19. Driver supplemental air bag/Horn
20. Cruise control main/set switch
21. Ignition switch/steering lock
22. Heater/air conditioner control
23. Coin box
24. Outside mirror remote control
25. Cellular phone holder
26. AWD lock switch (AWD models)
27. Heated seat switch*
28. Power outlet cover
29. Glove box
*: if so equipped
SSI0176
INSTRUMENT PANEL
2-2
Instruments and controls
hicle battery.
±
Avoid using power outlets when the
air
conditioner,
headlights
or
rear
window defroster is on.
±
Before inserting or disconnecting a
plug, be sure to turn off the power
switch of electrical accessory being
used or the ACC power of the vehicle.
±
Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.
±
When not in use, be sure to close the
cap/cover. Do not allow water to con-
tact the outlet.
COIN BOX
To open, push the coin box lid
²
1
as illustrated.
The inner tray can be removed
²
2
as illustrated.
Do not place valuable items in the box.
Do not use the coin box as an ashtray.
CELLULAR PHONE HOLDER
WARNING
±
A cellular telephone should not be
used while driving so full attention
may be given to vehicle operation.
Some jurisdictions prohibit the use
of cellular telephones while driving.
±
If a conversation in a moving vehicle
requires you to take notes, pull off
the road to a safe location and stop
SIC2057
SIC2058
STORAGE
Instruments and controls
2-31
The automatic drive positioner system has two
features:
±
Entry/exit function
±
Memory storage
ENTRY/EXIT FUNCTION
This system is designed so that the driver’s seat
and outside mirror will automatically move when
the selector lever is in the P (Park) position. This
allows the driver to get into and out of the
driver’s seat more easily.
The driver’s seat will slide backward:
The driver’s seat will slide backward when the
driver’s door is opened with the ignition switch
(knob) in the LOCK position.
The driver’s seat will return to the previous
position:
±
When the key is inserted into the ignition
switch after closing the driver’s door, or when
the driver’s door is closed after inserting the
key into the ignition switch.
±
When the ignition switch is pushed with the
driver’s
door
closed.
(Intelligent
Key
equipped model)
±
When the key or ignition switch is turned to
the ON position.
±
The driver’s seat will not return to the previ-
ous positions if the seat adjusting switch is
operated when the seat is at the exit position.
The entry/exit feature can be canceled. See “4.
Display screen, heater, air conditioner and audio
systems” section of this manual.
The entry/exit function can be activated or can-
celled by pressing and holding the SET switch
for more than 10 seconds while the ignition key
is in the LOCK position. The indicator light will
blink once when the function is cancelled, and
the indicator light will blink twice when the
function is activated. If the battery cable is
disconnected, or if the fuse opens, the entry/exit
function will be cancelled. In such a case, after
connecting the battery or replacing with a new
fuse, open and close the driver’s door more than
two times with the ignition key or ignition switch
in the LOCK position to activate the entry/exit
function.
MEMORY STORAGE
Two positions for the driver’s seat, pedals (Brake
and Accelerator) and outside mirrors can be
stored in the automatic drive positioner memory.
Follow these procedures to use the memory
system.
1. Set the selector lever to the P (Park) position.
2. Adjust the driver’s seat, pedals (Brake and
Accelerator) and outside mirrors to the de-
sired positions by manually operating each
adjusting switch. For additional information,
see “Seats” in the “1. Safety — seats, seat
belts
and
supplemental
restraint
system”
SPA2185
AUTOMATIC DRIVE POSITIONER
(if so equipped)
Pre-driving checks and adjustments
3-33
section and “Pedal position adjustment” and
“Outside mirrors” earlier in this section.
3. Turn the ignition ON.
4. Push the SET switch and, within 5 seconds,
push the memory switch (1 or 2) fully for at
least 1 second.
The indicator light for the pushed memory
switch will come on and stay on for approxi-
mately 5 seconds after pushing the switch.
After the indicator light goes off, the selected
positions are stored in the selected memory
(1 or 2).
If memory is stored in the same memory switch,
the previous memory will be deleted.
Linking a remote keyless entry to a
stored memory position
A remote keyless entry can be linked to a stored
memory position with the following procedure.
1. Follow the steps for storing a memory posi-
tion.
2. While
the
indicator
light
for
the
memory
switch being set is illuminated for 5 seconds,
push the unlock button on the remote keyless
entry. The indicator light will blink. After the
indicator light goes off, the remote keyless
entry is linked to that memory setting.
With the key removed from the ignition switch,
push the unlock button on the keyfob. The
driver’s seat, pedals (Brake and Accelerator)
and outside mirrors will move to the memorized
position.
Confirming memory storage
±
Turn the ignition switch to the ON position
and push the SET switch. If the main memory
has not been stored, the indicator light will
come
on
for
approximately
0.5
seconds.
When the memory has stored the position,
the indicator light will stay on for approxi-
mately 5 seconds.
±
If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using the
previous procedure.
±
If a new memory is stored, the previous
memory and link will be erased. In this case,
reset the desired position and link using the
previous procedure.
Selecting the memorized position
1. Set the selector lever to the P (Park) position.
2. Turn the ignition ON.
3. Push the memory switch (1 or 2) fully for at
least 1 second.
The driver’s seat, pedals (Brake and Accel-
erator) and outside mirrors will move to the
memorized position with the indicator light
flashing, and then the light will stay on for
approximately 5 seconds.
SYSTEM OPERATION
The automatic drive positioner system will not
work or will stop operating under the following
conditions:
±
when the vehicle speed is above 4 MPH (7
km/h).
±
when the adjusting switch for the driver’s
seat, pedals and outside mirror are operated
while the automatic drive positioner is oper-
ating.
±
when the memory switch (1 or 2) and the
SET switch is not pushed for at least 1
second.
±
when the seat, pedals and outside mirror
have been already moved to the memorized
positions.
±
when no seat, pedals and outside mirror
positions are stored in the memory switch.
±
when the engine is started while moving the
automatic drive positioner.
±
when the selector lever is moved from the P
3-34
Pre-driving checks and adjustments
change from stereo to monaural reception.
TUNE (Tuning):
To tune the radio, turn the TUNE knob to the
right or left.
Use these buttons for manual tuning.
SEEK tuning:
Push the SEEK button
or
for less
than 0.5 second to tune from high to low or low
to high frequencies and stop at the next broad-
casting station (channel).
Push the SEEK button
or
for more
than 0.5 second, to fast tune from high to low or
low to high frequencies.
SCAN tuning:
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broadcast-
ing station (channel) for 5 seconds. Pushing the
button again during this 5 seconds period will
stop SCAN tuning and the radio will remain
tuned to that station (channel).
If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next station
(channel).
Station memory operations:
Eighteen (18) stations can be set for the FM, AM
and SAT band to the A, B and C preset button.
1. Choose preset channel A, B or C using the
preset select button.
2. Tune to the desired station using the SEEK,
SCAN or TUNE button and keep pushing any
of the desired station memory buttons (1 to
6) until a beep sound is heard. (The radio
mutes when the select button is pushed.)
3. The channel indicator will then come on and
the sound will resume. Memorizing is now
complete.
4. Other buttons can be set in the same manner.
If the battery cable is disconnected, or if the fuse
blows, the radio memory will be erased. In that
case, reset the desired stations.
Radio data system (RDS):
RDS stands for Radio Data System, and is a
data information service transmitted by some
radio stations on the FM band (not AM band)
and/or SATELLITE band encoded within a regu-
lar radio broadcast. Currently, most RDS sta-
tions are in large cities, but many stations are
now considering broadcasting RDS data.
RDS can display:
±
Station call sign, such as “WHFR 98.3”.
±
Station name, such as “The Groove”.
±
Music or programming type such as “Classi-
cal”, “Country”, or “Rock”.
±
Traffic reports about delays or construction.
If the station broadcasts RDS information, the
RDS icon is displayed.
Category (CAT) button:
When the CAT button is pushed for less than
0.5 second, the AM/FM (Satellite) radio frequen-
cies (Category) will move to the next/previous
step (Category). Push and hold the button for
more than 0.5 second to move quickly through
the steps (Categories).
Compact disc (CD) player operation
Turn the ignition switch to the ACC or ON
position and insert the compact disc into the slot
with the label side facing up. The compact disc
will be guided automatically into the slot and
start playing.
After loading the disc, the number of tracks on
the disc and the play time will appear on the
display.
If the radio is already operating, it will automati-
cally turn off and the compact disc will play.
If the system has been turned off while the
compact
disc
was
playing,
pushing
the
POWER/VOL control knob will start the com-
pact disc.
4-36
Display screen, heater, air conditioner and audio systems
Display satellite radio text
To indicate the satellite radio text, push the
button while the satellite radio is playing.
The text will change as follows:
When no data is available, “——” will appear.
FM-AM-SAT radio operation
FM/AM/SAT radio select:
The satellite radio mode will be skipped unless
the optional satellite receiver and antenna are
installed, and an XM
or SIRIUS
TM
satellite radio
service subscription is active.
Pushing the RADIO button will change the band
as follows:
AM
FM
SAT (Satellite)
When the RADIO button is pushed while the
ignition switch is in the ACC or ON, the radio will
come on at the station last played.
The last station played will also come on when
the power knob is turned to ON.
If a compact disc or tape is playing when the
RADIO button is pushed, the compact disc or
tape will automatically be turned off and the last
radio station played will come on.
The FM stereo indicator ST will glow during FM
stereo reception. When the stereo broadcast
signal
is
weak,
the
radio
will
automatically
change from stereo to monaural reception.
TUNE (Tuning):
To tune the radio, turn the TUNE knob to the
right or left.
Use these buttons for manual tuning.
SEEK tuning:
Push the SEEK button
or
for less
than 0.5 second to tune from high to low or low
to high frequencies and stop at the next broad-
casting station (channel).
Push the SEEK button
or
for more
than 0.5 second, to fast tune from high to low or
low to high frequencies.
SCAN tuning:
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broadcast-
ing station (channel) for 5 seconds. Pushing the
button again during this 5 seconds period will
stop SCAN tuning and the radio will remain
tuned to that station (channel).
If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next station
(channel).
Station memory operations:
Eighteen (18) stations can be set for the FM, AM
and SAT band to the A, B and C preset button.
1. Choose preset channel A, B or C using the
preset select button.
2. Tune to the desired station using the SEEK,
SCAN or TUNE button and keep pushing any
of the desired station memory buttons (1 to
6) until a beep sound is heard. (The radio
mutes when the select button is pushed.)
3. The channel indicator will then come on and
the sound will resume. Memorizing is now
complete.
4. Other buttons can be set in the same manner.
If the battery cable is disconnected, or if the fuse
blows, the radio memory will be erased. In that
case, reset the desired stations.
Radio data system (RDS):
RDS stands for Radio Data System, and is a
data information service transmitted by some
radio stations on the FM band (not AM band)
and/or SATELLITE band encoded within a regu-
lar radio broadcast. Currently, most RDS sta-
tions are in large cities, but many stations are
4-40
Display screen, heater, air conditioner and audio systems
1. Power steering fluid reservoir
2. Engine oil filler cap
3. Brake fluid reservoir
4. Air cleaner
5. Windshield washer fluid reservoir
6. Engine coolant reservoir
7. Drive belts
8. Radiator filler cap
9. Engine oil dipstick
10. Fuse/fusible link holder
11. Battery
SDI1760
ENGINE COMPARTMENT CHECK
LOCATIONS
Maintenance and do-it-yourself
8-7
Some vehicles are equipped with engine com-
partment
and
passenger
compartment
fuse
boxes that use only type
²
A
fuses. Other ve-
hicles are equipped with type
²
A
fuses in the
engine compartment fuse box and type
²
B
fuses
in the passenger compartment fuse box.
Type
²
A
fuses are provided as spare fuses. They
are stored in the passenger compartment fuse
box.
Type
²
A
fuses can be installed in the engine
compartment and passenger compartment fuse
boxes.
If a type
²
A
fuse is used to replace a type
²
B
fuse, the type
²
A
fuse will not be level with the
fuse pocket as shown in the illustration. This will
not affect the performance of the fuse. Make
sure the fuse is installed in the fuse box securely.
Type
²
B
fuses cannot be installed in the under-
hood fuse boxes. Only use type
²
A
fuses in the
underhood fuse boxes.
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
SDI1751
SDI1752
SDI1504
FUSES
Maintenance and do-it-yourself
8-21
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch and headlight
switch are OFF.
2. Open the engine hood.
3. Remove the fusible link cover.
4. Remove the fuse with the fuse puller.
5. If the fuse is open
²
A
, replace it with a new
fuse
²
B
.
6. If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
Fusible links
If any electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace only with genuine NISSAN parts.
SDI1753
Type A
SDI1754
Type B
8-22
Maintenance and do-it-yourself
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Pull to open the fuse box lid
²
1
.
3. Pinch the fuse perpendicularly with the fuse
puller
²
A
and pull it out.
4. If the fuse is open, replace it with a new fuse
²
B
.
5. If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
KEYFOB
Replace the battery as follows:
1. Open the lid using a suitable tool.
2. Replace the battery with a new one.
SDI1505
SPA1374
BATTERY REPLACEMENT
Maintenance and do-it-yourself
8-23