Nissan Altima Sedan - 2006 Fuse Box Diagram

Nissan Altima Sedan - 2006 Fuse Box Diagram

QR25DE engine
1.
Power steering fluid reservoir (P. 8-16)
2.
Spark plug caps (P. 8-21)
3.
Brake fluid reservoir (P. 8-17)
4.
Clutch fluid reservoir (M/T model)
(P. 8-17)
5.
Air cleaner (P. 8-22)
6.
Battery (P. 8-18)
7.
Fuse/fusible link box (P. 8-27)
8.
Transmission dipstick (A/T models)
(P. 8-14)
9.
Engine oil dipstick (P. 8-10)
10.
Radiator cap (P. 8-9)
11.
Drive belt location (P.8-20)
12.
Fuse block (P. 8-27)
13.
Windshield washer fluid reservoir
(P. 8-18)
14.
Engine coolant reservoir (P. 8-9)
15.
Engine oil filler cap (P. 8-10)
NOTE:
Engine cover removed for clarity.
See the page number indicated in paren-
theses for operating details.
WDI0488
ENGINE COMPARTMENT CHECK
LOCATIONS
0-8
Illustrated table of contents
VQ35DE engine
1.
Power steering fluid reservoir (P. 8-16)
2.
Engine oil filler cap (P. 8-10)
3.
Brake fluid reservoir (P. 8-17)
4.
Clutch fluid reservoir (M/T model)
(P. 8-17)
5.
Air cleaner (P. 8-22)
6.
Battery (P. 8-18)
7.
Fuse/fusible link box (P. 8-27)
8.
Transmission dipstick (A/T models)
(P. 8-16)
9.
Engine oil dipstick (P. 8-10)
10.
Radiator cap (P. 8-9)
11.
Drive belt location (P.8-20)
12.
Fuse block (P. 8-27)
13.
Windshield washer fluid reservoir
(P. 8-18)
14.
Engine coolant reservoir (P. 8-9)
NOTE:
Engine cover removed for clarity.
See the page number indicated in paren-
theses for operating details.
WDI0489
Illustrated table of contents
0-9
Before
inserting
or
disconnecting
a
plug, be sure the electrical accessory
being used is turned OFF.
Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may open.
When not in use, be sure to close the
cap. Do not allow water to contact the
outlet.
The cigarette lighter operates when the ignition
switch is in the ACC or ON position.
Lift the lid
s
A
to open.
Push the lighter
s
B
in all the way. When the
lighter is heated, it will spring out. Return the
lighter to its original position after use.
Pull out the ashtray
s
C
to remove it.
This power outlet can also be used for powering
electrical
accessories
such
as
cellular
tele-
phones.
CAUTION
The cigarette lighter should not be used
while driving so full attention may be
given to vehicle operation.
The outlet and plug may be hot during
or immediately after use.
Do not use any other power outlet for an
accessory lighter.
Do not use with accessories that ex-
ceed a 12 volt, 120W (10A) power draw.
Do not use double adapters or more
than one electrical accessory.
Use power outlets with the engine run-
ning to avoid discharging the vehicle
battery.
Avoid using power outlets when the air
conditioner, headlights or rear window
defroster is on.
Before
inserting
or
disconnecting
a
plug, be sure the electrical accessory
being used is turned OFF.
Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may open.
LIC0692
CIGARETTE LIGHTER AND ASHTRAY
(if so equipped)
Instruments and controls
2-29
Press the PRESET ABC button to change be-
tween the presets:
A
B
C
The radio displays icon A, B or C to indicate
which set of presets is active.
To store a radio station in a preset:
1. Select the desired preset by pressing PRE-
SET ABC.
2. Select the desired AM, FM or SAT (if so
equipped) station band.
3. Tune to the desired station.
4. Press
the
desired
station
select
button
(>1.5 seconds).
5. A beep will sound indicating memorization is
complete.
6. Other station select buttons can be set in
the same manner.
If the battery cable is disconnected, or if the radio
fuse opens, the radio memory is canceled. In that
case, reset the desired stations.
Preset Scan
Pressing the Preset Scan button (<1.5 seconds)
scans the permanent preset memory that is se-
lected (A, B or C) from 1 - 6 for 5 seconds.
All Preset Scan
Pressing the Preset Scan button (>1.5 seconds)
scans all the permanent preset memory banks (A,
B and C) from 1 - 6 for 5 seconds.
Canceling Preset Scan mode
Pressing the Preset Scan (P.SCAN) button again
will cancel the Preset Scan mode.
Speed Sensitive Control Volume (SSV) (if
so equipped)
Your vehicle has Speed Sensitive Control Vol-
ume (SSV) for audio. The audio volume changes
as the driving speed changes.
Press the AUDIO button until the display shows
“SSV”.
Press TUNE/FF-REV (
or
)
to change between:
Off
Low
Mid
High
Compact disc (CD) player operation
Turn the ignition key to the ACC or ON position.
CAUTION
Do not force a compact disc into the CD
insert slot. This could damage the CD
and/or CD changer/player.
Trying to load a CD with the CD door
closed could damage the CD and/or CD
changer.
CD button
When the CD button is pressed with a compact
disc loaded and the radio playing, the radio turns
off and the last used compact disc starts to play.
FF (Fast Forward), REW
(Rewind) buttons
When the TUNE/FF-REV (
or
) but-
ton is pressed while the compact disc is playing,
the compact disc plays at an increased speed
while fast forwarding or rewinding. When the
button is released, the compact disc returns to
normal play speed.
SEEK/TRACK buttons
When
is pressed while the compact disc
is playing, the next track following the present
one
starts
to
play
from
the
beginning.
Press
several times to skip several tracks.
Each time the button is pressed, the CD ad-
vances 1 additional track. The track number ap-
pears in the display window. (When the last track
on the compact disc is skipped, the first track is
played.)
Display screen, heater, air conditioner and audio systems
4-27
The FM stereo indicator ST will glow during FM
stereo reception. When the stereo broadcast
signal is weak, the radio will automatically change
from stereo to monaural reception.
TUNE/FF—REV
WARNING
The radio should not be tuned while driv-
ing so full attention may be given to ve-
hicle operation.
Use the
and
buttons for manual
tuning. To move quickly through the channels,
hold the tuning buttons down.
SEEK tuning
Push SEEK/TRACK (
or
). SEEK
tuning begins from low to high frequencies or
high to low frequencies, depending on which
button is pressed, and stops at the next broad-
casting station. If using the up button, once the
highest broadcasting station is reached, the ra-
dio continues in the SEEK mode at the lowest
broadcasting station. If using the down button,
once the lowest broadcasting station is reached,
the radio continues in the SEEK mode at the
highest broadcasting station.
SCAN tuning
Push the SCAN button. SCAN illuminates in the
display window. SCAN tuning begins from low to
high frequencies. SCAN tuning stops for 5 sec-
onds at each broadcasting station that has suffi-
cient signal strength. When scanning, SCAN
blinks in the display. Pushing the SCAN button
again during this 5 second period stops SCAN
tuning and the radio remains tuned to that station.
Station memory operation
Each preset mode (A, B or C) has 6 presets,
capable of storing any combination of AM, FM,
SAT (if so equipped ) and FM RDS stations.
Press the PRESET ABC button to change be-
tween the presets:
A
B
C
The radio displays icon A, B or C to indicate
which set of presets is active.
To store a radio station in a preset:
1. Select the desired preset by pressing PRE-
SET ABC.
2. Select the desired AM, FM or SAT (if so
equipped) station band.
3. Tune to the desired station.
4. Press
the
desired
station
select
button
(>1.5 seconds).
5. A beep will sound indicating memorization is
complete.
6. Other station select buttons can be set in
the same manner.
If the battery cable is disconnected, or if the radio
fuse opens, the radio memory is canceled. In that
case, reset the desired stations.
Radio data system (RDS):
RDS stands for Radio Data System, and is a data
information service transmitted by some radio
stations on the FM band (not AM band) and/or
SAT radio encoded within a regular radio broad-
cast. Currently, most RDS stations are in large
cities, but many stations are now considering
broadcasting RDS data.
RDS can display:
Station call sign, such as “WHFR 98.3”.
Station name, such as “The Groove”.
Music or programming type such as “Clas-
sical”, “Country”, or “Rock”.
If the station broadcasts RDS information, the
RDS icon is displayed.
Display screen, heater, air conditioner and audio systems
4-31
4. The channel indicator will then come on and
the sound will resume. Memorizing is now
complete.
5. Other buttons can be set in the same man-
ner.
If the battery cable is disconnected, or if the fuse
blows, the radio memory will be canceled. In that
case, reset the desired stations.
Radio data system (RDS):
RDS stands for Radio Data System, and is a data
information service transmitted by some radio
stations on the FM band (not AM band) and/or
SAT radio encoded within a regular SAT broad-
cast. Currently, most RDS stations are in large
cities, but many stations are now considering
broadcasting RDS data.
RDS can display:
Station call sign, such as “WHFR 98.3”.
Station name, such as “The Groove”.
Music or programming type such as “Clas-
sical”, “Country” or “Rock”.
If the station broadcasts RDS information, the
RDS icon is displayed.
Program type (PTY):
PTY can be used to search for a certain program
type. Certain areas have a limited number of
stations that transmit RDS. Many stations trans-
mit call letters and frequencies only.
Searching or scanning by program type may yield
a limited number of selections.
When CAT/RPT button is pressed for more than
1.5 seconds during FM or SAT (if so equipped)
mode, the PTY name of the current tuned station
is displayed. During this time if the PTY data code
is zero or the data is unreadable, the display will
show NONE.
To change the PTY:
1. Press the CAT/RPT button.
2. Press the TUNE/FF-REV (
or
)
up/down button to chose a specific program
type.
ROCK, CLASSIC ROCK, SOFT ROCK,
TOP 40, COUNTRY, JAZZ, CLASSICAL,
OLDIES, NEWS, SPORTS, TALK, ANY
SEEK tuning:
3. After selecting a program type, push the
SEEK/TRACK button (
or
) for
less than 1.5 seconds within 10 seconds.
Tuning to the PTY station will start. If you do
not push the SEEK button within the 10
second period, the PTY mode will be can-
celed.
SCAN tuning:
4. Push the SCAN button for more than 1.5
seconds to scan the PTY name stations and
stop at each broadcasting station for 5 sec-
onds. Pushing the button again during this 5
second period will stop SCAN tuning and
the radio will remain tuned to that station. If
the SCAN button is not pushed within 5
seconds, SCAN tuning moves to the next
station.
Compact disc (CD) changer operation
CAUTION
Do not force a compact disc into the CD
insert slot. This could damage the CD
and/or CD changer/player.
Trying to load a CD with the CD door
closed could damage the CD and/or CD
changer.
4-38
Display screen, heater, air conditioner and audio systems
QR25DE engine
1.
Power steering fluid reservoir
2.
Spark plug coils
3.
Brake fluid reservoir
4.
Clutch fluid reservoir (M/T model)
5.
Air cleaner
6.
Battery
7.
Fuse/Fusible link box
8.
Transmission dipstick (A/T models)
9.
Engine oil dipstick
10.
Radiator cap
11.
Drive belt location
12.
Fuse block
13.
Windshield washer fluid reservoir
14.
Engine coolant reservoir
15.
Engine oil filler cap
NOTE:
Engine cover removed for clarity.
WDI0488
ENGINE COMPARTMENT CHECK
LOCATIONS
Maintenance and do-it-yourself
8-7
VQ35DE engine
1.
Power steering fluid reservoir
2.
Engine oil filler cap
3.
Brake fluid reservoir
4.
Clutch fluid reservoir (M/T model)
5.
Air cleaner
6.
Battery
7.
Fuse/Fusible link box
8.
Transmission dipstick (A/T models)
9.
Engine oil dipstick
10.
Radiator cap
11.
Drive belt location
12.
Fuse block
13.
Windshield washer fluid reservoir
14.
Engine coolant reservoir
NOTE:
Engine cover removed for clarity.
WDI0489
8-8
Maintenance and do-it-yourself
Self-adjusting brakes
Your
vehicle
is
equipped
with
self-adjusting
brakes.
The front and rear disc-type brakes self-adjust
every time the brake pedal is applied.
WARNING
See a NISSAN dealer for a brake system
check if the brake pedal height does not
return to normal.
Brake pad wear indicators
The disc brake pads on your vehicle have audible
wear indicators. When a brake pad requires re-
placement, a high pitched scraping or screech-
ing sound will be heard when the vehicle is in
motion. The noise will be heard whether or not the
brake
pedal
is
depressed.
Have
the
brakes
checked as soon as possible if the wear indicator
sound is heard.
Under some driving or climate conditions, occa-
sional brake squeak, squeal or other noise may
be heard. Occasional brake noise during light to
moderate stops is normal and does not affect the
function or performance of the brake system.
Proper brake inspection intervals should
be followed.
For more information regarding
brake inspections, see the appropriate mainte-
nance schedule information in the “NISSAN Ser-
vice and Maintenance Guide”.
BRAKE BOOSTER
Check the brake booster function as follows:
1. With the engine off, press and release the
brake
pedal
several
times.
When
brake
pedal movement (distance of travel) remains
the same from one pedal application to the
next, continue on to the next step.
2. While depressing the brake pedal, start the
engine. The pedal height should drop a little.
3. With the brake pedal depressed, stop the
engine. Keep the pedal depressed for about
30 seconds. The pedal height should not
change.
4. Run the engine for one minute without de-
pressing the brake pedal, then turn it off.
Depress the brake pedal several times. The
pedal travel distance will decrease gradually
with each depression as the vacuum is re-
leased from the booster.
If the brakes do not operate properly, have the
brakes checked by a NISSAN dealer.
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not come on,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Open the engine hood.
WDI0230
FUSES
Maintenance and do-it-yourself
8-27
3. Remove the fuse box cover by pushing the
tab and lifting the cover up.
4. Remove the fuse with the fuse puller. The
fuse puller is located in the center of the fuse
block in the passenger compartment.
5. If the fuse is open
s
A
, replace it with a new
fuse
s
B
.
6. If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
Fusible links
If the electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace with only genuine NISSAN parts.
WDI0452
8-28
Maintenance and do-it-yourself
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Pull the fuse box cover to remove.
3. Remove the fuse with the fuse puller.
4. If the fuse is open
s
A
, replace it with a known
good fuse
s
B
.
5. Push the fuse box cover to install.
6. If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
WDI0402
Type A
WDI0452
Maintenance and do-it-yourself
8-29