Nissan Quest - 2013 Fuse Box Diagram

Nissan Quest - 2013 Fuse Box Diagram

0-6
Illustrated table of contents
GUID-F7B216D8-F960-48DA-8767-559E890BB396
SSI0825
1.
Vehicle Dynamic Control (VDC) OFF switch
(P.2-40)
2.
Blind Spot Warning (BSW) switch* (P.2-39)
— Blind Spot Warning (BSW)* (P.5-17)
3.
Sliding door switch* (driver’s side) (P.3-9)
4.
Sliding door switch* (passenger’s side) (P.3-9)
5.
Instrument brightness control switch (P.2-37)
6.
Power lift gate switch* (P.3-26)
7.
Headlight, fog light and turn signal switch
— Headlight (P.2-33)
— Turn signal (P.2-37)
— Fog light* (P.2-37)
8.
Trip computer switch (P.2-22)
9.
TRIP/RESET switch for twin trip odometer
(P.2-6)
10.
Wiper and washer switch (P.2-30)
11.
Fuse box cover (P.8-20)
12.
Fuel-filler door opener handle (P.3-30)
13.
Hood release handle (P.3-25)
14.
Headlight aiming control* (P.2-36)
15.
Power door main switch* (P.3-9, P.3-27)
16.
Steering-wheel-mounted controls (left side)
— Audio control steering switch* (P.4-102)
— Hands-Free Phone System switch* (P.4-115,
P.4-126)
17.
Horn (P.2-38)
18.
Steering-wheel-mounted controls (right side)
— Cruise control system (P.5-24)
*:
if so equipped
COCKPIT
GUID-3A4CEA77-5BE4-4FE6-B1A8-2659A7636D0E
SDI2715
VQ35DE ENGINE
GUID-EEC870E3-1878-4751-8AE6-5D5884DD625A
1.
Power steering fluid reservoir (P.8-11)
2.
Drive belt location (P.8-15)
3.
Engine oil filler cap (P.8-8)
4.
Brake fluid reservoir (P.8-12)
5.
Air cleaner (P.8-17)
6.
Fuse/fusible link holder (P.8-20)
7.
Window washer fluid reservoir (P.8-13)
8.
Engine coolant reservoir (P.8-7)
9.
Radiator filler cap (P.8-7)
10.
Engine oil dipstick (P.8-8)
11.
Battery (P.8-13)
Illustrated table of contents
0-9
ENGINE COMPARTMENT
GUID-DCC2794A-4B62-4A96-BA3A-A529DCB296EE
SSI0825
1.
Vehicle Dynamic Control (VDC) OFF switch
2.
Blind Spot Warning (BSW) switch*
— Blind Spot Warning (BSW)*
3.
Sliding door switch* (driver’s side)
4.
Sliding door switch* (passenger’s side)
5.
Instrument brightness control switch
6.
Power lift gate switch*
7.
Headlight, fog light and turn signal switch
— Headlight
— Turn signal
— Fog light*
8.
Trip computer switch
9.
TRIP/RESET switch for twin trip odometer
10.
Wiper and washer switch
11.
Fuse box cover
12.
Fuel-filler door opener handle
13.
Hood release handle
14.
Headlight aiming control*
15.
Power door main switch*
16.
Steering-wheel-mounted controls (left side)
— Audio control steering switch*
— Hands-Free Phone System switch*
17.
Horn
18.
Steering-wheel-mounted controls (right side)
— Cruise control system
*:
if so equipped
Instruments and controls
2-3
COCKPIT
ing after adjusting the tire pressure,
a tire may be flat. If you have a flat
tire, replace it with a spare tire as
soon as possible.
.
When a spare tire is mounted or a
wheel is replaced, the TPMS will not
function and the low tire pressure
warning light will flash for approxi-
mately
1
minute.
The
light
will
remain on after 1 minute. Contact
your
NISSAN
dealer
as
soon
as
possible for tire replacement and/
or system resetting.
.
Replacing tires with those not ori-
ginally specified by NISSAN could
affect the proper operation of the
TPMS.
CAUTION
.
The TPMS is not a substitute for the
regular tire pressure check. Be sure
to check the tire pressure regularly.
.
If
the
vehicle
is
being
driven
at
speeds of less than 16
MPH (25
km/h), the TPMS may not operate
correctly.
.
Be
sure
to
correctly
install
the
specified size of tires to the four
wheels.
Master warning light
GUID-AE6F59CE-42B9-444F-B156-919C688575F5
When the ignition switch is in the ON position,
the master warning light illuminates if any of the
following are displayed on the dot matrix liquid
crystal display:
.
No key warning
.
Low fuel warning
.
Low washer fluid warning
.
Parking brake release warning
.
Door/lift gate open warning
.
Loose fuel cap warning
.
Check tire pressure warning
.
Extended
storage
fuse
warning
(if
so
equipped)
See “Dot matrix liquid crystal display” (P.2-18).
Seat belt warning light and chime
GUID-A109F64D-D61F-4A96-AD87-98431E7D57E1
The light and chime remind you to fasten seat
belts. The light illuminates whenever the ignition
switch is pushed to the ON position, and will
remain illuminated until the driver’s seat belt is
fastened. At the same time, the chime will sound
for approximately 6 seconds unless the driver’s
seat belt is securely fastened.
The
seat
belt
warning
light
for
the
front
passenger will illuminate if the seat belt is not
fastened when the front passenger’s seat is
occupied. For approximately 5 seconds after the
ignition switch is in the ON position, the system
does not activate the warning light for the front
passenger.
See “Seat belts” (P.1-16) for precautions on
seat belt usage.
Supplemental air bag warning light
GUID-053868B0-D825-4DAD-80BD-8335FF04C712
After pushing the ignition switch to the ON
position, the supplemental air bag warning light
will illuminate. The supplemental air bag warning
light will turn off after about 7 seconds if the
supplemental front air bag and supplemental
side air bag, curtain side-impact air bag systems
and/or pretensioner seat belt are operational.
If any of the following conditions occur, the front
air
bag,
side
air
bag,
curtain
air
bag
and
pretensioner systems needs servicing and your
vehicle must be taken to your nearest NISSAN
dealer.
.
The
supplemental
air
bag
warning
light
remains on after approximately 7 seconds.
.
The
supplemental
air
bag
warning
light
flashes intermittently.
.
The supplemental air bag warning light does
not come on at all.
Instruments and controls
2-15
11. Loose fuel cap warning
GUID-AE37C079-2D1D-4EC5-BC3E-A6F3746AC355
This warning appears when the fuel-filler cap is
not tightened correctly after the vehicle has
been refueled. (See “Fuel-filler cap” (P.3-30).)
12. Check tire pressure warning
GUID-DA5B077D-A7AE-4C80-ABBC-FC03EE16A559
This warning appears when the low tire pressure
warning light in the meter illuminates and low tire
pressure is detected. The warning appears each
time the ignition switch is placed in the ON
position as long as the low tire pressure warning
light remains illuminated. If this warning appears,
stop the vehicle and adjust the tire pressure to
the recommended COLD tire pressure shown
on the Tire and Loading Information label. (See
“Low tire pressure warning light” (P.2-14) and
“Tire Pressure Monitoring System (TPMS)” (P.5-
3).)
13. “TIMER” indicator
GUID-1125717D-01A2-4EE0-BD94-FCEC2E95C1E9
This indicator appears when the set “timer”
indicator activates. You can set the time for up to
6 hours. (See “Trip computer” (P.2-22).)
14. Low outside temperature warning
GUID-05A3065E-96A4-4FAF-9E94-F0DF064F6767
This warning appears if the outside temperature
is below 37
8
F (3
8
C). The warning can be set not
to be displayed. (See “Trip computer” (P.2-22).)
15. Extended storage fuse warning (if so
equipped)
GUID-6AB8FBE8-1539-40E0-88C7-FC678D1B5DB6
This warning may appear if the extended storage
fuse switch is not pushed in (switched on).
When this warning appears, push in (switch on)
the extended storage fuse switch to turn off the
warning. For more information, see “Extended
storage fuse switch” (P.8-21).
SIC4237
Instruments and controls
2-21
SIC4723
Instrument panel
SIC4724
Cargo area
Type A
To use the power outlet, pull the cover as
illustrated.
CAUTION
.
The
outlet
and
plug
may
be
hot
during or immediately after use.
.
Do not use with accessories that
exceed a 12 volt, 120W (10A) power
draw. Do not use double adapters or
more than one electrical accessory.
.
This power outlet is not designed
for use with a cigarette lighter unit.
.
Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.
SIC2648
Main switch
Type B (if so equipped)
The power outlet (plug type) is located on the
front console. It can operate when the ignition
switch in the ON position and the main switch
(located on the instrument panel) is ON.
The specification of this power outlet is for
use of a 120 volt, 150W (1.25A) power draw.
To turn on or off the power supply to the outlet,
push the ON
*
1
or OFF
*
2
side of the main
switch. When the switch is turned to the ON
position, the indicator light
*
A
will illuminate.
Instruments and controls
2-41
GUID-D7276E5F-FB84-463B-BDF9-A346295A447B
The automatic drive positioner system has two
features:
.
Entry/exit function
.
Memory storage
ENTRY/EXIT FUNCTION
GUID-5F29AE45-A8DA-42BF-A7C8-04256D167074
This system is designed so that the driver’s seat
will automatically move when the selector lever
is in the P (Park) position. This allows the driver
to get into and out of the driver’s seat more
easily.
The driver’s seat will slide backward when the
driver’s door is opened with the ignition switch
in the LOCK position.
The driver’s seat will return to the previous
positions when the ignition switch is pushed to
the ACC position.
The driver’s seat will not return to the previous
positions if the seat adjusting switch is operated
when the seat is at the exit position.
Cancel or activate entry/exit function
GUID-97B13C13-98B1-43DA-BF4E-6CC11E5EE734
The selector lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The
entry/exit
function
can
be
activated
or
canceled
by
pressing
and
holding
the
SET
switch for more than 10 seconds.
The indicator lights on the memory switches (1
and 2) will blink once when the function is
canceled, and the indicator lights will blink twice
when the function is activated. Note that the
indicator lights may illuminate after 5 seconds
while holding the SET switch. This indicates
readiness for linking the Intelligent Key to a
stored memory position. Keep the SET switch
pressed for more than 10 seconds to turn on or
off the entry/exit function.
The entry/exit function can also be activated or
canceled if the “Slide Driver Seat Back on Exit”
key is turned to ON or OFF in the “Comfort”
settings. (See “Vehicle information and settings
(models with center multi-function control pa-
nel)” (P.4-8).)
Initialize entry/exit function
GUID-E526DD89-2FEC-4DC6-8386-CED70B431AFF
If the battery cable is disconnected, or if the fuse
opens,
the
entry/exit
function
will
not
work
though this function was set on before. In such
a case, after connecting the battery or replacing
with a new fuse, open and close the driver’s
door more than two times after the ignition
switch is placed in the LOCK position from the
ON
position.
The
entry/exit
function
will
be
activated.
SPA2855
MEMORY STORAGE
GUID-BEDCA7A8-8409-4EC2-8EAE-7F30A20C2AA8
Two positions for the driver’s seat and outside
mirrors can be stored in the automatic drive
positioner memory. Follow this procedure to use
the memory system.
1.
Move the selector lever to the P (Park)
position.
2.
Push the ignition switch to the ON position.
3.
Adjust the driver’s seat and outside mirrors
to the desired positions by manually operat-
ing each adjusting switch. For additional
information, see “Seats” (P.1-2) and “Out-
side mirrors” (P.3-35).
Pre-driving checks and adjustments
3-37
AUTOMATIC DRIVE POSITIONER (if
so equipped)
3-38
Pre-driving checks and adjustments
4.
Push the SET switch and, within 5 seconds,
push the memory switch (1 or 2).
The indicator light for the pushed memory
switch
will
stay
on
for
approximately
5
seconds after pushing the switch.
If memory is stored in the same memory
switch, the previous memory will be deleted.
Linking Intelligent Key to a stored mem-
ory position
GUID-04712762-5C07-46C9-89DF-7F2803A498EB
The Intelligent Key can be linked to a stored
memory position with the following procedure.
1.
Follow one of the steps for storing a memory
position.
.
While the indicator light for the memory
switch being set is illuminated for 5 sec-
onds, push the
button on the Intelligent
Key.
.
Push the ignition switch to the OFF position,
and then push the SET switch. Push the
button while pushing the memory button
while the indicator light stays on for approxi-
mately 5 seconds.
If the indicator light blinks, the Intelligent Key is
linked to that memory setting.
Push the ignition switch to the OFF position, and
then push the
button on the Intelligent Key.
The driver’s seat and outside mirrors will move to
the memorized position.
Confirming memory storage
GUID-C7D22E67-E6D7-436F-A7E9-FBD8970F3E83
.
Push the ignition switch to the ON position
and
push
the
SET switch.
If
the
main
memory has not been stored, the indicator
light will come on for approximately 0.5
second. When the memory has stored in
position, the indicator light will stay on for
approximately 5 seconds.
.
If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using
the previous procedure.
.
If optional keys are added to your vehicle,
the memory storage procedure to switch 1
or 2 and linking Intelligent Key procedure to
a stored memory position should be per-
formed again for each Intelligent Key. For
additional Intelligent Key information, see
“Keys” (P.3-3).
Selecting the memorized position
GUID-66874194-881E-4A22-96FF-EE790B2F0E22
1.
Move the selector lever to the P (Park)
position.
2.
Use one of the following methods to move
the driver’s seat and outside mirrors.
.
Push
the
ignition
switch
to
the
ON
position and push the memory switch (1
or 2).
.
Within
45
seconds
of
opening
the
driver’s door, push the memory switch
(1 or 2).
The driver’s seat and outside mirrors will
move to the memorized position with the
indicator light flashing, and then the light will
stay on for approximately 5 seconds.
SYSTEM OPERATION
GUID-B0CC6635-8934-4D55-BA9A-D54FF3D35461
The automatic drive positioner system will not
work or will stop operating under the following
conditions:
.
When the vehicle speed is above 4 MPH (7
km/h) (entry/exit function).
.
When the vehicle is driven (memory sto-
rage).
.
When the adjusting switch for the driver’s
seat is turned on while the automatic drive
positioner is operating.
.
When the driver’s seat and outside mirrors
have already been moved to the memorized
position.
.
When no position is stored in the memory
switch.
.
When the engine is started while moving the
automatic drive positioner.
.
When the selector lever is moved from the P
(Park) position to any other position. (How-
ever, it will not be canceled while the driver’s
4-76
Monitor, heater, air conditioner, audio, phone and voice recognition systems
period will stop SCAN tuning and the radio will
remain tuned to that station/channel.
If the Radio SCAN tuning button is not pushed
within 5 seconds, SCAN tuning moves to the
next station/channel.
*
1
to
*
6
Station memory operations:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2), 18 for SiriusXM
Satellite Radio (6 each for XM1, XM2 and XM3)
and 6 stations can be set for the AM band.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station/channel using
the SEEK·CAT, SCAN button or the radio
TUNE·SCROLL control knob.
3.
Push and hold the desired station preset
button
*
1
to
*
6
until the radio mutes.
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations/channels.
SAA3607
Compact Disc (CD) player operation
GUID-4EB7CD04-F4EC-4584-BA97-A08FF4F31188
Place the ignition switch in the ACC or ON
position and insert the Compact Disc (CD) into
the slot with the label side facing up. The CD will
be guided automatically into the slot and start
playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If the radio is already operating, it will auto-
matically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the PWR button will start
the CD.
Do not use 3.1 in (8 cm) discs.
PLAY:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the CD·AUX button is pushed with the
system off and the CD loaded, the system will
turn on and the CD will start to play.
When the CD·AUX button is pushed with the
CD loaded and the radio playing, the radio will
automatically be turned off and the CD will start
to play.
Next/Previous Track and Fast
Forward/Rewind:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the FF or REW button is pushed for more
than 1.5 seconds while the CD is being played,
the
CD
will
play
while
fast
forwarding
or
rewinding. When the button is released, the
CD will return to normal play speed.
When the FF or REW button is pushed for less
than 1.5 seconds while the CD is being played,
the next track or the beginning of the current
track on the CD will be played.
.
UPDATING (When the satellite radio sub-
scription is not active)
SCAN tuning:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broad-
casting station/channel for 5 seconds. Pushing
the button again during this 5 seconds period
will stop SCAN tuning and the radio will remain
tuned to that station/channel.
If the SCAN tuning button is not pushed within 5
seconds,
SCAN
tuning
moves
to
the
next
station/channel.
*
1
to
*
6
Station memory operations:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2), 18 for SiriusXM
Satellite Radio (6 each for XM1, XM2 and XM3)
and 6 stations can be set for the AM band.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station/channel using
the
SEEK/TRACK,
SCAN
button
or
the
radio TUNE knob.
3.
Push and hold the desired station preset
button
*
1
to
*
6
until the radio mutes.
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations/channels.
List (AM and FM radio) (models with
navigation system):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “List” key on the display is selected
while the FM or AM radio is being played, the
preset station list will be displayed.
If 1 of the 6 preset stations listed is touched and
held, the current station will be stored as the
new preset.
Menu (SiriusXM Satellite Radio):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “Menu” key on the display is selected
while
the
SiriusXM
Satellite
Radio
is
being
played, the menu list will be displayed.
The following items are available.
.
Preset List
Displays the preset channel list. If 1 of the 6
preset stations listed is touched and held,
the current station will be stored as the new
preset.
.
Customize Channel List
Selects specific channels to skip while using
the
TUNE,
SEEK/CATEGORY or
Menu-
Categories feature.
.
Favorite Artists & Songs
Stores the current artist or song that is being
played. Touch the “Alert” key to be reminded
when the stored artist or song is playing on a
station while listening to SiriusXM Satellite
Radio.
.
Categories
Selecting a category will go to the first
channel
in
that
category
as
defined
by
SiriusXM Satellite Radio.
.
Direct Tune
Inputs
the
channel
number
by
using
a
keypad.
Text (models without navigation system):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “Text” key is selected with the multi-
function controller on the display and then the
ENTER button is pushed while the satellite radio
is being played, the text information listed below
will be displayed on the screen.
.
CH Name
.
Category
.
Name
.
Title
.
Other
Monitor, heater, air conditioner, audio, phone and voice recognition systems
4-83
8-6
Maintenance and do-it-yourself
affect warranty coverage.
If in doubt about
any servicing, we recommend that it be
done by a NISSAN dealer.
GUID-8DF375C4-D2AC-40BF-8919-179130A7B1A6
SDI2715
VQ35DE ENGINE
GUID-2BF22F9C-AD70-479A-B6B1-C3822E0C8D88
1.
Power steering fluid reservoir
2.
Drive belt location
3.
Engine oil filler cap
4.
Brake fluid reservoir
5.
Air cleaner
6.
Fuse/fusible link holder
7.
Window washer fluid reservoir
8.
Engine coolant reservoir
9.
Radiator filler cap
10.
Engine oil dipstick
11.
Battery
ENGINE COMPARTMENT CHECK
LOCATIONS
8-20
Maintenance and do-it-yourself
GUID-2A7EB98C-06EB-4C49-B4CD-5F466EB75D08
SDI2181
ENGINE COMPARTMENT
GUID-CA4EBE21-B3CE-413F-A37D-F2E747557888
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Open the engine hood.
3.
Remove the fuse/fusible link holder cover by
pushing the tab
*
1
.
4.
Remove the fuse with the fuse puller located
in the passenger compartment fuse box.
SDI1754
5.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
. Spare fuses are stored in the
passenger compartment fuse box.
6.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
Fusible links
GUID-35942A92-B8C3-4636-8D6F-137D926C007D
If any electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace only with genuine NISSAN parts.
FUSES
JVM0187X
PASSENGER COMPARTMENT
GUID-377BDCAB-1F2D-4209-92B3-FFBA626F3776
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Pull to remove the fuse box cover
*
1
.
3.
Remove the fuse with the fuse puller
*
2
.
4.
If the fuse is open, replace it with a new fuse.
5.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
SDI2704
Extended storage fuse switch
GUID-2BFC6F36-C181-408E-ACC9-7BC9BA96C2A2
To reduce battery drain, the extended storage
fuse switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If
the
extended
storage
fuse
switch
is
not
pushed in (switched on), the "SHIPPING MODE
ON,
PUSH
STORAGE
FUSE"
warning
may
appear on the dot matrix liquid crystal display.
See “Dot matrix liquid crystal display” (P.2-18).
If any electrical equipment does not operate,
remove the extended storage fuse switch and
check for an open fuse.
Maintenance and do-it-yourself
8-21
8-22
Maintenance and do-it-yourself
NOTE:
If the extended storage fuse switch mal-
functions, or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
1.
To remove the extended storage fuse switch,
be sure the ignition switch is in the OFF or
LOCK position.
2.
Be sure the headlight switch is in the OFF
position.
3.
Remove the fuse box cover.
4.
Pinch the locking tabs
*
1
found on each
side of the storage fuse switch.
5.
Pull the storage fuse switch straight out from
the fuse box
*
2
.
GUID-CA8545B0-9BF6-43C6-A676-EFA5AA3A5260
CAUTION
Be
careful
not
to
allow
children
to
swallow the battery and removed parts.
SDI2451
Replace the battery as follows:
1.
Remove the mechanical key from the key.
2.
Insert a small screwdriver into the slit of the
corner and twist it to separate the upper part
from the lower part. Use a cloth to protect
the casing.
INTELLIGENT KEY BATTERY
REPLACEMENT