Nissan JUKE - 2014 Fuse Box Diagram

Nissan JUKE - 2014 Fuse Box Diagram

JVC0572X
1.
Outside mirror remote control switch (P.3-25)
2.
Headlight, fog light and turn signal switch
— Headlight (P.2-35)
— Turn signal light (P.2-38)
— Fog light* (P.2-39)
3.
Paddle shifter* (P.5-20)
4.
Steering wheel
— Electric power steering system (P.5-38)
— Horn (P.2-39)
— Driver’s supplemental air bag (P.1-38)
5.
Wiper and washer switch (P.2-32)
6.
Shift lever
— Continuously Variable Transmission (CVT)
(P.5-17)
— Manual Transmission (MT) (P.5-23)
7.
Fuse box cover (P.8-21)
8.
Vehicle Dynamic Control (VDC) OFF switch
(P.5-41)
9.
All-Wheel Drive (AWD) switch* (P.5-33)
10.
Tilting steering wheel lever (P.3-23)
11.
Steering-wheel-mounted controls (left side)
— Audio control (P.4-69)
— Bluetooth
®
Hands-Free Phone System con-
trol (P.4-72, P.4-85)
12.
Ignition switch (models without Intelligent Key
system) (P.5-10)
13.
Steering-wheel-mounted controls (right side)
— Cruise control switches (P.5-30)
14.
Heated seat switch* (P.2-40)
*:
if so equipped
Illustrated table of contents
0-7
COCKPIT
0-10
Illustrated table of contents
SDI2639
MR16DDT ENGINE
1.
Engine oil filler cap (P.8-8)
2.
Radiator filler cap (P.8-8)
— Vehicle overheat (P.6-10)
3.
Brake and clutch* fluid reservoir (P.8-11)
4.
Air cleaner (P.8-16)
5.
Window washer fluid reservoir (P.8-12)
6.
Engine drive belt location (P.8-15)
7.
Engine oil dipstick (P.8-8)
8.
Engine coolant reservoir (P.8-8)
9.
Fuse/fusible link holder (P.8-19)
10.
Battery (P.8-13)
— Jump starting (P.6-8)
*:
for Manual Transmission (MT) models
ENGINE COMPARTMENT
JVC0572X
1.
Outside mirror remote control switch
2.
Headlight, fog light and turn signal switch
— Headlight
— Turn signal light
— Fog light*
3.
Paddle shifter*
4.
Steering wheel
— Electric power steering system
— Horn
— Driver’s supplemental air bag
5.
Wiper and washer switch
6.
Shift lever
— Continuously Variable Transmission (CVT)
— Manual Transmission (MT)
7.
Fuse box cover
8.
Vehicle Dynamic Control (VDC) OFF switch
9.
All-Wheel Drive (AWD) switch*
10.
Tilting steering wheel lever
11.
Steering-wheel-mounted controls (left side)
— Audio control
— Bluetooth
®
Hands-Free Phone System con-
trol
12.
Ignition switch (models without Intelligent Key
system)
13.
Steering-wheel-mounted controls (right side)
— Cruise control switches
14.
Heated seat switch*
*:
if so equipped
Instruments and controls
2-3
COCKPIT
SPA2809
Loose fuel cap warning message
Push the reset switch
*
A
for more than 1
second to reset the LOOSE FUEL CAP warning
message after the fuel cap has been tightened.
For additional information see “Fuel-filler cap”
(P.3-21) of this manual.
JVI0326X
Check tire pressure warning message
The CHECK TIRE PRES (pressure) warning
message is displayed when the low tire pressure
warning light
is illuminated and low tire
pressure is detected. Check and adjust the tire
pressure
to
the
recommended
COLD
tire
pressure
shown
on
the
Tire
and
Loading
Information
label.
The
CHECK
TIRE
PRES
warning message turns off when the low tire
pressure warning light
turns off.
The low tire pressure warning light
remains
illuminated until the tires are inflated to the
recommended COLD tire pressure. The CHECK
TIRE PRES warning message is displayed each
time the ignition switch is placed in the ON
position as long as the low tire pressure warning
light
remains illuminated.
For more information see “Low tire pressure
warning light” (P.2-15), “Tire Pressure Monitor-
ing System (TPMS)” (P.5-4), and “Wheels and
tires” (P.8-30).
Extended storage fuse warning message
The SHIPPING MODE ON/PUSH STORAGE
FUSE warning message may be displayed if the
extended storage fuse switch is not pushed in
(switched on). When this message is displayed,
push in (switch on) the extended storage fuse
switch
to
turn
off
the
message.
For
more
information, see “Extended storage fuse switch”
(P.8-22).
Instruments and controls
2-7
2-42
Instruments and controls
SIC4525
The power outlet is located in the instrument
panel.
CAUTION
.
The
outlet
and
plug
may
be
hot
during or immediately after use.
.
Do not use with accessories that
exceed a 12 volt, 120W (10A) power
draw. Do not use double adapters or
more than one electrical accessory.
.
Use power outlet with the engine
running
to
avoid
discharging
the
vehicle battery.
.
Avoid using power outlet when the
air conditioner, headlights or rear
window defroster is on.
.
This power outlet is not designed
for use with a cigarette lighter unit.
.
Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.
.
Before inserting or disconnecting a
plug, be sure the electrical acces-
sory being used is turned OFF.
.
When not in use, be sure to close
the cap. Do not allow water or any
liquid to contact the outlet.
CUP HOLDERS
CAUTION
.
Avoid abrupt starting and braking
when the cup holder is being used
to prevent spilling the drink. If the
liquid is hot, it can scald you or your
passenger.
.
Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.
POWER OUTLET
STORAGE
during this 5 seconds period will stop SCAN
tuning and the radio will remain tuned to that
station.
If the SCAN tuning button is not pushed within 5
seconds,
SCAN
tuning
moves
to
the
next
station.
to
Station memory operations:
12 stations can be set for the FM band (6 each
for FM1 and FM2), 18 for SiriusXM Satellite
Radio (6 each for XM1, XM2 and XM3)* and 6
can be set for the AM band for easy access.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station using the SEEK,
SCAN or TUNE button.
3.
Push and hold the desired radio station
preset button
to
until a beep sound is
heard. (The radio mutes when the radio
station preset button is pushed.)
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations.
*: if so equipped
Radio Data System (RDS):
RDS stands for Radio Data System, and is a
data information service transmitted by some
radio stations on the FM band (not AM band)
encoded
within
a
regular
radio
broadcast.
Currently, most RDS stations are in large cities,
but many stations are now considering broad-
casting RDS data.
RDS can display:
.
Station call sign, such as “WHFR 98.3”.
.
Station name, such as “The Groove”.
.
Music or programming type such as “Clas-
sical”, “Country” or “Rock”.
.
Traffic reports about delays or construction.
If the station broadcasts RDS information, the
RDS icon is displayed.
RADIO DISPLAY change:
When the DISP/TEXT button is pushed during
the FM or SAT radio mode, the radio display will
change in the following order.
.
For FM radio:
Frequency
PS (Programme Service)/PTY
(Programme type)
.
For SiriusXM Satellite Radio*:
Category Name
?
Channel Name
?
Artist/
Feature
?
Song/Program
In the FM radio mode, pushing the DISP/TEXT
button will switch the frequency display to the
PTY display (if available), and if the DISP/TEXT
button is not pushed again within 5 seconds, it
will automatically switch to the PS display. If PTY
is not available, pushing the DISP/TEXT button
will only switch between the frequency display
and the PS display.
*: if so equipped
Heater, air conditioner, audio and phone systems
4-43
4-50
Heater, air conditioner, audio and phone systems
frequency. To return to the regular radio display
screen, touch the “OK” key.
to
Station memory operations:
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2), 18 for SiriusXM
Satellite Radio (6 each for XM1, XM2 and XM3)
and 6 stations can be set for the AM band.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station/channel using
the SEEK/CATEGORY button or the TUNE
knob.
3.
Push and hold the desired station preset
button
to
until the beep sound is
heard.
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations/channels.
Channels (SiriusXM Satellite Radio):
When the SiriusXM Satellite Radio is being
played, select “Channels” key to display a list of
channels. Select a preferred channel from the
list to change to that channel.
Categories (SiriusXM Satellite Radio):
When the SiriusXM Satellite Radio is being
played, select “Categories” key to display a list
of channels. Select a preferred channel from the
list to display options within that category.
Compact Disc (CD) player operation
Place the ignition switch in the ACC or ON
position and insert the Compact Disc (CD) into
the slot with the label side facing up. The CD will
be guided automatically into the slot and start
playing.
If the radio is already operating, it will auto-
matically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the ON·OFF button will
start the CD.
Do not use 3.1 in (8 cm) discs.
PLAY:
When the CD button is pushed with the system
off and the CD loaded, the system will turn on
and the CD will start to play.
When the CD button is pushed with the CD
loaded and the radio playing, the radio will
automatically be turned off and the CD will start
to play.
While listening to a CD or an MP3/WMA CD,
certain
text
may
be
displayed
(when
a
CD
encoded with text is being used). Depending on
how the CD or MP3/WMA CD is encoded, the
text is displayed listing the artist, album and
song title.
Next/Previous Track and Fast
Forward/Rewind:
When the
or
button is pushed for more
than 1.5 seconds while the CD is being played,
the
CD
will
play
while
fast
forwarding
or
rewinding. When the button is released, the
CD will return to normal play speed.
When the
or
button is pushed for less
than 1.5 seconds while the CD is being played,
the next track or the beginning of the current
track on the CD will be played.
When the rewind button is pushed for less than
1.5 seconds within 3 seconds after the current
track starts playing, the previous track will be
played.
4-60
Heater, air conditioner, audio and phone systems
3.
The channel indicator will then come on and
the sound will resume. Programming is now
complete.
4.
Other keys can be set in the same manner.
If the battery cable is disconnected or if the fuse
opens, the radio memory will be canceled. In
that case, reset the desired stations.
Presets can also be selected by touching the
desired preset number on the screen.
Compact Disc (CD) player operation
If the radio is already operating, it automatically
turns off and the compact disc begins to play.
CD button:
When the CD button is pushed with the system
off and the compact disc loaded, the system will
turn on and the compact disc will start to play.
When the CD button is pushed with a compact
disc loaded and the radio playing, the radio will
automatically be turned off and the compact
disc will start to play.
CD/MP3/WMA display mode:
Menu item
CD/MP3 display mode
While listening to a CD or an MP3/WMA CD, certain text may be displayed (when a
CD encoded with text is being used). Depending on how the CD or MP3/WMA CD
is encoded, the text is displayed listing the artist, album and song title. There are
other keys displayed on the screen when a CD is playing:
Random
Touch the “Random” key to apply a random play pattern to the CD. If an MP3 CD is
playing, touching “Random” or alternates between Random Folder, and Random All.
This text will appear on the display. To cancel Random mode, touch the “Random”
key until the key is no longer highlighted.
Repeat
Touch the “Repeat” key to apply a repeat play pattern to the CD. If an MP3 CD is
playing, touching “Repeat” alternates between repeating the current song and
repeating the current folder. This text will appear on the display. To cancel Repeat
mode, touch the “Repeat” key until the key is no longer highlighted.
Browse
Touch the “Browse” key to display the titles on the CD in list format. Touch the title of
a song in the list to begin playing that song. If an MP3 CD is playing, touching the
“Browse” key will also list the folders on the disc. Follow the procedure for selecting a
song with the touch-screen to choose a folder.
8-6
Maintenance and do-it-yourself
improper
servicing
may
result
in
operating
difficulties or excessive emissions, and could
affect
your
warranty
coverage.
If
in
doubt
about any servicing, we recommend that
it be done by a NISSAN dealer.
SDI2639
MR16DDT ENGINE
1.
Engine oil filler cap
2.
Radiator filler cap
3.
Brake and clutch* fluid reservoir
4.
Air cleaner
5.
Window washer fluid reservoir
6.
Engine drive belt location
7.
Engine oil dipstick
8.
Engine coolant reservoir
9.
Fuse/fusible link holder
10.
Battery
*:
for Manual Transmission (MT) models
ENGINE COMPARTMENT CHECK
LOCATIONS
light to moderate stops is normal and does not
affect the function or performance of the brake
system.
Proper brake inspection intervals should
be followed.
For additional information, see the
maintenance
log
section
of
your
“NISSAN
Service and Maintenance Guide”.
SDI2654
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Open the engine hood.
3.
Remove the fuse/fusible link holder cover by
pushing the tab
*
1
and lifting the cover
from the right side
*
2
, then the left side
*
3
.
4.
Locate the fuse that needs to be replaced.
5.
Remove
the
fuse
using
the
fuse
puller
located in the passenger compartment fuse
box.
Maintenance and do-it-yourself
8-19
FUSES
8-20
Maintenance and do-it-yourself
SDI1754
6.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
.
7.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
The holder
*
4
also contains the fuses. For
checking and/or replacing, see a NISSAN
dealer.
SDI2642
Fusible links
If any electrical equipment does not operate and
the fuses are in good
condition, check the
fusible links in the holders
*
1
and
*
2
. If any of
these fusible links are melted, replace only with
genuine NISSAN parts.
For checking and replacing the fusible links in
the holders
*
2
, see a NISSAN dealer.
SDI2643
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Remove the fuse box cover
*
1
.
3.
Remove the fuse with the fuse puller
*
2
.
SDI1754
4.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
.
5.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
Maintenance and do-it-yourself
8-21
8-22
Maintenance and do-it-yourself
SDI2705
Extended storage fuse switch (if so
equipped)
To reduce battery drain, the extended storage
fuse switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If
the
extended
storage
fuse
switch
is
not
pushed in (switched on), the meter may display
a warning message. See “Extended storage fuse
warning message” (P.2-7).
If any electrical equipment does not operate,
remove the extended storage fuse switch and
check for an open fuse.
NOTE:
If the extended storage fuse switch mal-
functions or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
1.
To remove the extended storage fuse switch,
be sure the ignition switch is in the OFF or
LOCK position.
2.
Be sure the headlight switch is in the OFF
position.
3.
Remove the fuse box cover.
4.
Pinch the storage fuse switch and pull it in
the direction illustrated.
CAUTION
Be
careful
not
to
allow
children
to
swallow the battery and removed parts.
KEY BATTERY REPLACEMENT
JVC0572X
1.
Outside mirror remote control switch (P.3-25)
2.
Headlight, fog light and turn signal switch
— Headlight (P.2-35)
— Turn signal light (P.2-38)
— Fog light* (P.2-39)
3.
Paddle shifter* (P.5-20)
4.
Steering wheel
— Electric power steering system (P.5-38)
— Horn (P.2-39)
— Driver’s supplemental air bag (P.1-36)
5.
Wiper and washer switch (P.2-32)
6.
Shift lever
— Continuously Variable Transmission (CVT)
(P.5-17)
— Manual Transmission (MT) (P.5-23)
7.
Fuse box cover (P.8-21)
8.
Vehicle Dynamic Control (VDC) OFF switch
(P.5-41)
9.
All-Wheel Drive (AWD) switch* (P.5-33)
10.
Tilting steering wheel lever (P.3-23)
11.
Steering-wheel-mounted controls (left side)
— Audio control (P.4-48)
— Bluetooth
®
Hands-Free Phone System con-
trol (P.4-50)
12.
Ignition switch (models without Intelligent Key
system) (P.5-10)
13.
Steering-wheel-mounted controls (right side)
— Cruise control switches (P.5-30)
14.
Heated seat switch* (P.2-40)
*:
if so equipped
Illustrated table of contents
0-7
COCKPIT
0-10
Illustrated table of contents
SDI2639
MR16DDT ENGINE
1.
Engine oil filler cap (P.8-8)
2.
Radiator filler cap (P.8-8)
— Vehicle overheat (P.6-10)
3.
Brake and clutch* fluid reservoir (P.8-11)
4.
Air cleaner (P.8-16)
5.
Window washer fluid reservoir (P.8-12)
6.
Engine drive belt location (P.8-15)
7.
Engine oil dipstick (P.8-8)
8.
Engine coolant reservoir (P.8-8)
9.
Fuse/fusible link holder (P.8-19)
10.
Battery (P.8-13)
— Jump starting (P.6-8)
*:
for Manual Transmission (MT) models
ENGINE COMPARTMENT
JVC0572X
1.
Outside mirror remote control switch
2.
Headlight, fog light and turn signal switch
— Headlight
— Turn signal light
— Fog light*
3.
Paddle shifter*
4.
Steering wheel
— Electric power steering system
— Horn
— Driver’s supplemental air bag
5.
Wiper and washer switch
6.
Shift lever
— Continuously Variable Transmission (CVT)
— Manual Transmission (MT)
7.
Fuse box cover
8.
Vehicle Dynamic Control (VDC) OFF switch
9.
All-Wheel Drive (AWD) switch*
10.
Tilting steering wheel lever
11.
Steering-wheel-mounted controls (left side)
— Audio control
— Bluetooth
®
Hands-Free Phone System con-
trol
12.
Ignition switch (models without Intelligent Key
system)
13.
Steering-wheel-mounted controls (right side)
— Cruise control switches
14.
Heated seat switch*
*:
if so equipped
Instruments and controls
2-3
COCKPIT
SPA2809
Loose fuel cap warning message
Push the reset switch
*
A
for more than 1
second to reset the LOOSE FUEL CAP warning
message after the fuel cap has been tightened.
For additional information see “Fuel-filler cap”
(P.3-21) of this manual.
JVI0326X
Check tire pressure warning message
The CHECK TIRE PRES (pressure) warning
message is displayed when the low tire pressure
warning light
is illuminated and low tire
pressure is detected. Check and adjust the tire
pressure
to
the
recommended
COLD
tire
pressure
shown
on
the
Tire
and
Loading
Information
label.
The
CHECK
TIRE
PRES
warning message turns off when the low tire
pressure warning light
turns off.
The low tire pressure warning light
remains
illuminated until the tires are inflated to the
recommended COLD tire pressure. The CHECK
TIRE PRES warning message is displayed each
time the ignition switch is placed in the ON
position as long as the low tire pressure warning
light
remains illuminated.
For more information see “Low tire pressure
warning light” (P.2-15), “Tire Pressure Monitor-
ing System (TPMS)” (P.5-4), and “Wheels and
tires” (P.8-30).
Extended storage fuse warning message
The SHIPPING MODE ON/PUSH STORAGE
FUSE warning message may be displayed if the
extended storage fuse switch is not pushed in
(switched on). When this message is displayed,
push in (switch on) the extended storage fuse
switch
to
turn
off
the
message.
For
more
information, see “Extended storage fuse switch”
(P.8-22).
Instruments and controls
2-7
2-42
Instruments and controls
SIC4525
The power outlet is located in the instrument
panel.
CAUTION
.
The
outlet
and
plug
may
be
hot
during or immediately after use.
.
Do not use with accessories that
exceed a 12 volt, 120W (10A) power
draw. Do not use double adapters or
more than one electrical accessory.
.
Use power outlet with the engine
running
to
avoid
discharging
the
vehicle battery.
.
Avoid using power outlet when the
air conditioner, headlights or rear
window defroster is on.
.
This power outlet is not designed
for use with a cigarette lighter unit.
.
Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.
.
Before inserting or disconnecting a
plug, be sure the electrical acces-
sory being used is turned OFF.
.
When not in use, be sure to close
the cap. Do not allow water or any
liquid to contact the outlet.
CUP HOLDERS
CAUTION
.
Avoid abrupt starting and braking
when the cup holder is being used
to prevent spilling the drink. If the
liquid is hot, it can scald you or your
passenger.
.
Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.
POWER OUTLET
STORAGE
Radio (SAT) band select:
Pushing the
button will change the band as
follows:
AUX (if connected portable device)
?
XM1*
?
XM2*
?
XM3*
?
AUX (if connected portable
device)
The last channel played will also come on when
the ON·OFF button is pushed to ON.
When the stereo broadcast signal is weak, the
radio will automatically change from stereo to
monaural reception.
When the radio band select button is pushed
while the ignition switch is in the ACC or ON
position, the radio will come on at the station last
played.
*: if so equipped
TUNE (Tuning):
.
For AM and FM radio
Push the TUNE button
or
for
manual tuning. To move quickly through the
stations, push and hold the TUNE button.
.
For SiriusXM Satellite Radio*
Push the TUNE button
or
to seek
stations from all of the categories when any
CAT is not selected.
*: if so equipped
SEEK tuning CATEGORY:
.
For AM and FM radio
Push the SEEK button
or
to tune
from low to high or high to low frequencies
and to stop at the next broadcasting station.
.
For SiriusXM Satellite Radio*
Push the
or
to tune to the first
station of the next or previous category.
*: if so equipped
During satellite radio reception, the following
notices will be displayed under certain condi-
tions.
.
NO SIGNAL (No signal is received while the
SAT tuner is connected.)
.
OFF AIR (Broadcasting signed off)
.
CHECK
ANTENNA
(Antenna
connection
error)
.
LOADING
(When
the
initial
setting
is
performed)
.
UPDATING (When the satellite radio sub-
scription is not active)
.
INVALID CH (Invalid channel is received.)
SCAN tuning:
Push the SCAN button to tune from low to high
frequencies and stops at each broadcasting
station for 5 seconds. Pushing the button again
during this 5 seconds period will stop SCAN
tuning and the radio will remain tuned to that
station.
If the SCAN tuning button is not pushed within 5
seconds,
SCAN
tuning
moves
to
the
next
station.
to
Station memory operations:
12 stations can be set for the FM band (6 each
for FM1 and FM2), 18 for SiriusXM Satellite
Radio (6 each for XM1, XM2 and XM3)* and 6
can be set for the AM band for easy access.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station using the SEEK,
SCAN or TUNE button.
3.
Push and hold the desired radio station
preset button
to
until a beep sound is
heard. (The radio mutes when the radio
station preset button is pushed.)
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations.
Heater, air conditioner, audio and phone systems
4-33
4-40
Heater, air conditioner, audio and phone systems
TUNE (Tuning):
.
For AM and FM radio
Turn the TUNE knob for manual tuning.
.
For SiriusXM Satellite Radio
Turn the TUNE knob to seek channels from
all of the categories when any category is
not selected.
SEEK tuning:
.
For AM and FM radio
Push the SEEK/CATEGORY button
or
to tune from low to high or high to low
frequencies and to stop at the next broad-
casting station.
.
For SiriusXM Satellite Radio
Push the SEEK/CATEGORY button
or
to tune to the first channel of the next or
previous category.
Tuning with the touch screen (AM and FM
radio):
When in AM or FM mode, the radio can be
tuned using the touch screen. To bring up the
visual tuner, touch the “Tune” key on the lower
right corner of the screen. A screen appears
with a bar running from low frequencies on the
left to high frequencies on the right. Touch the
screen at the location of the frequency you wish
to tune and the station will change to that
frequency. To return to the regular radio display
screen, touch the “OK” key.
to
Station memory operations:
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2), 18 for SiriusXM
Satellite Radio (6 each for XM1, XM2 and XM3)
and 6 stations can be set for the AM band.
1.
Choose the radio band using the radio band
select button.
2.
Tune to the desired station/channel using
the SEEK/CATEGORY button or the TUNE
knob.
3.
Push and hold the desired station preset
button
to
until the beep sound is
heard.
4.
The station indicator will then come on and
the sound will resume. Memorizing is now
complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations/channels.
Channels (SiriusXM Satellite Radio):
When the SiriusXM Satellite Radio is being
played, select “Channels” key to display a list of
channels. Select a preferred channel from the
list to change to that channel.
Categories (SiriusXM Satellite Radio):
When the SiriusXM Satellite Radio is being
played, select “Categories” key to display a list
of channels. Select a preferred channel from the
list to display options within that category.
Compact Disc (CD) player operation
Place the ignition switch in the ACC or ON
position and insert the Compact Disc (CD) into
the slot with the label side facing up. The CD will
be guided automatically into the slot and start
playing.
If the radio is already operating, it will auto-
matically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the ON·OFF button will
start the CD.
Do not use 3.1 in (8 cm) discs.
PLAY:
When the CD button is pushed with the system
off and the CD loaded, the system will turn on
and the CD will start to play.
When the CD button is pushed with the CD
loaded and the radio playing, the radio will
automatically be turned off and the CD will start
to play.
8-6
Maintenance and do-it-yourself
improper
servicing
may
result
in
operating
difficulties or excessive emissions, and could
affect
your
warranty
coverage.
If
in
doubt
about any servicing, we recommend that
it be done by a NISSAN dealer.
SDI2639
MR16DDT ENGINE
1.
Engine oil filler cap
2.
Radiator filler cap
3.
Brake and clutch* fluid reservoir
4.
Air cleaner
5.
Window washer fluid reservoir
6.
Engine drive belt location
7.
Engine oil dipstick
8.
Engine coolant reservoir
9.
Fuse/fusible link holder
10.
Battery
*:
for Manual Transmission (MT) models
ENGINE COMPARTMENT CHECK
LOCATIONS
light to moderate stops is normal and does not
affect the function or performance of the brake
system.
Proper brake inspection intervals should
be followed.
For additional information, see the
maintenance
log
section
of
your
“NISSAN
Service and Maintenance Guide”.
SDI2654
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Open the engine hood.
3.
Remove the fuse/fusible link holder cover by
pushing the tab
*
1
and lifting the cover
from the right side
*
2
, then the left side
*
3
.
4.
Locate the fuse that needs to be replaced.
5.
Remove
the
fuse
using
the
fuse
puller
located in the passenger compartment fuse
box.
Maintenance and do-it-yourself
8-19
FUSES
8-20
Maintenance and do-it-yourself
SDI1754
6.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
.
7.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
The holder
*
4
also contains the fuses. For
checking and/or replacing, see a NISSAN
dealer.
SDI2642
Fusible links
If any electrical equipment does not operate and
the fuses are in good
condition, check the
fusible links in the holders
*
1
and
*
2
. If any of
these fusible links are melted, replace only with
genuine NISSAN parts.
For checking and replacing the fusible links in
the holders
*
2
, see a NISSAN dealer.
SDI2643
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Remove the fuse box cover
*
1
.
3.
Remove the fuse with the fuse puller
*
2
.
SDI1754
4.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
.
5.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
Maintenance and do-it-yourself
8-21
8-22
Maintenance and do-it-yourself
SDI2705
Extended storage fuse switch (if so
equipped)
To reduce battery drain, the extended storage
fuse switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If
the
extended
storage
fuse
switch
is
not
pushed in (switched on), the meter may display
a warning message. See “Extended storage fuse
warning message” (P.2-7).
If any electrical equipment does not operate,
remove the extended storage fuse switch and
check for an open fuse.
NOTE:
If the extended storage fuse switch mal-
functions or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
1.
To remove the extended storage fuse switch,
be sure the ignition switch is in the OFF or
LOCK position.
2.
Be sure the headlight switch is in the OFF
position.
3.
Remove the fuse box cover.
4.
Pinch the storage fuse switch and pull it in
the direction illustrated.
CAUTION
Be
careful
not
to
allow
children
to
swallow the battery and removed parts.
KEY BATTERY REPLACEMENT