Kia Amanti - 2004 Fuse Box Diagram

Kia Amanti - 2004 Fuse Box Diagram

1
2
3
4
5
6
7
8
9
Knowing your vehicle
Power windows
The ignition switch must be in the ON
position for power windows to oper-
ate. Each door has a power window
switch that controls that door’s win-
dow. However, the driver has a power
window lock switch which can block
the operation of passenger windows.
If you notice buffeting and pulsation
(wind shock) with either side window
open, you should open the opposite
window slightly to reduce the condi-
tion.
NOTICE
To prevent the power window sys-
tem from the possibility of damage,
do not open or close two windows at
the same time. This will also ensure
the longevity of the fuse.
CAUTION
• Do not allow children to play
with the power windows. Keep
the driver’s door power win-
dow lock switch in the LOCK
position (depressed). Serious
injury can result from uninten-
tional window operation by
the child.
• Do not extend face or arms
outside through the window
opening while driving.
Always double check to make
sure all arms, hands and other
obstructions are safely out of
the way before closing a win-
dow
1
2
3
4
5
6
7
8
9
Knowing your vehicle
NOTICE
Use when the engine is running.
• Only use the electric appliances
which are less than 12V and 10A
in electric capacity.
• Adjust the air-conditioner or
heater to the lowest operation
level when you have to use the
power socket while using air-con-
ditioner or heater.
Close the cover when not in use.
Clock
Digital (if equipped)
Whenever the battery terminals, A/V
CLOCK fuse, or Power Connect are
disconnected, you must reset the
time.
Press the Clock Control PUSH but-
ton in front of the monitor to access
the mode set buttons.
Use these
buttons to adjust the time/date dis-
played on the monitor.
1. Press the MODE button (
).
2. Select the mode to be reset; hour
(
), minute (
), month (
) and
date (
).
3. Reset the data using button
(
)
or button
(
) while the selected
mode blinks.
If the
(
) or
(
) button(s) are
pressed for more than 3 seconds,
the display will begin to change
rapidly. When the
(
) or
(
)
button(s)
are
pressed
then
released, the display will change
in single increments.
4. Press the SET (
) button when
the data is correctly set.
1GHA2110
6 7
In case of an emergency
ELECTRICAL CIRCUIT PROTECTION
Fuses
A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses.
This vehicle has two fuse panels,
one located in the driver's side knee
bolster, the other in the engine com-
partment near the battery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside the
fuse will be melted.
If the electrical system does not
work, first check the driver’s side
fuse panel.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and imme-
diately consult an Authorized Kia
Dealer.
Two kinds of fuses are used: stan-
dard for lower amperage rating and
main for higher amperage ratings.
1
2
3
4
5
6
7
8
9
MMSA6003
Standard
Main fuse
Normal
Normal
Blown
Blown
In case of an emergency
8
6
Fuse replacement
1. Turn the ignition switch and all
other switches off.
2. Pull the suspected fuse straight
out. Use the removal tool provided
on the main fuse box in the engine
compartment.
3. Check the removed fuse; replace it
if it is blown.
Spare fuses are provided in the
fuse panel.
4. Push in a new fuse of the same
rating, and make sure it fits tightly
in the clips.
If it fits loosely, consult an Authorized
Kia Dealer.
If you do not have a spare, use a
fuse of the same rating from a circuit
you may not need for operating the
vehicle, such as the radio or room
lamp fuse.
If the headlights or other electrical
components do not work and the
fuses are OK, check the fuse block in
the engine compartment. If a fuse is
blown, it must be replaced.
1
2
3
4
5
6
7
8
9
1GHA402
WARNING
- Fuse replace-
ment
Never replace a fuse with any-
thing but another fuse of the
same rating.
• A higher capacity fuse could
cause damage and possibly a
fire.
Never install a wire instead of
the proper fuse - even as a
temporary repair. It may cause
extensive wiring damage and
possibly a fire.
• Do not use a screwdriver or
any other metal object to
remove fuses because it may
cause a short circuit and dam-
age the system.
Driver - side knee bolster
6 9
In case of an emergency
To check the fuse or relay in the
engine compartment, remove the
engine compartment shroud.
1. Turn the ignition switch and all
other switches off.
2. Remove the fuse box cover by
removing the bolt on the cover and
unhooking the tab on one end and
tilting the cover back toward the
other end.
3. Check the fuses. If one is blown,
replace it with a new one of the
same rating.
NOTICE
After checking the fuse box in the
engine
compartment,
securely
install the fuse box cover.
If not,
electrical failures may occur from
water leaking in.
Main fuse
If the BATT (60A) or ALT (140A) fuse
are blown, it must be removed as fol-
lows:
1. Disconnect the negative battery
cable.
2. Remove the screws shown in the
picture above.
3. Replace the fuse with a new one
of the same rating.
4. Reinstall in the reverse order of
removal.
1
2
3
4
5
6
7
8
9
1GHA404
1GHA411
1GHA405
Engine compartment
Junction Box
Main Fuse
Relay Box
6 11
In case of an emergency
1
2
3
4
5
6
7
8
9
Fuse/Relay panel description
Inside the fuse/relay box covers, you can find the fuse/relay label describing fuse/relay name and capacity.
C/FAN
20A
FUSE
PULLER
P/SEAT(FR)
30A
H/
LP
(LO-LH)
HORN
START
IGN SW-2
30A
R/FAN
30A
R/FAN
A/CON FAN-2
WIPER (LO)
TAIL
LP
H/
LP
(HI)
A/CON FAN-1
FOG
LP
(FR)
FUEL PUMP
A/CON
1
6
2
7
3
8
11
12
16
20
15
14
17
18
22
23
19
25
24
27
21
13
9
10
4
5
28
26
IGN SW-1
30A
ABS 2
30A
ABS 1
30A
1. FUEL PUMP
2. H/LP (LO-LH)
3. ABS
4. INJECTOR
5. A/CON COMP
6. ATM RLY
7. ECU RLY
8. IGN COIL
9. O2 SNSR
10. ENG SNSR
(20A)
(15A)
(10A)
(10A)
(10A)
(20A)
(20A)
(20A)
(15A)
(15A)
11. HORN
12. TAIL LP
13. H/LP WASHER
14. ETS
15. FOG LP (FR)
16. H/LP (HI)
17. SPARE
18. SPARE
19. SPARE
20. SPARE
(15A)
(20A)
(20A)
(20A)
(15A)
(15A)
(30A)
(20A)
(15A)
(10A)
21. BLOWER MTR
22. S/WARMER
23. AMP
24. DRL
25. H/LP (LO-RH)
26. P/FUSE-1
27. ECU
28. ECS
NOT USED
(30A)
(30A)
(20A)
(15A)
(15A)
(30A)
(10A)
(15A)
USE THE DESIGNATED FUSE AND RELAY ONLT.
Engine compartment
10A
B/ALARM
15A
A/BAG
20A
C/LIGHTER
10A
S/WARMER
20A
P/WDW(RH)
15A
P/HANDLE
15A
T/SIG LP
30A
HTD GLASS
15A
TRUNK OPEN
SHUNT CONN
USE ONLY DESIGNATED FUSE ONLY
POWER/CONN
15A
STOP LP
10A
MIRROR HTD
10A
LAN UNIT
10A
B/ALARM
10A
DR LP
15A
AV.CLOCK
30A
P/SEAT(RR)
10A
BACK WARN'G
10A
ROOM LP
15A
F/LID OPEN
10A
TAIL LP(RH)
10A
TAIL LP(LH)
15A
FOG LP(RR), PIC
20A
P/WDW(LH)
10A
EPS
10A
CURTAIN(RR)
10A
A/CON
20A
WIPER(FR)
10A
LAN UNIT
10A
H/LP
10A
CLOCK
20A
P/OUTLET
10A
T/REDUCER
10A
AV
10A
A/BAG IND
10A
B/UP LP
10A
CLUSTER
10A
ENG SNSR
10A
TRIP COMPUTER
2GHN603/2GHN604
Driver-side knee bolster
In case of an emergency
12
6
1
2
3
4
5
6
7
8
9
Description
Fuse rating
Protected component
1
FUEL PUMP
20A
Fuel pump
2
H/LP (LO-LH)
15A
Headlight (low-left)
3
ABS
10A
Anti-lock brake system
4
INJECTOR
10A
Injector
5
A/CON COMP
10A
Air-conditioner compressor
6
ATM RLY
20A
Automatic transaxle control relay
7
ECU RLY
20A
Engine control unit relay
8
IGN COIL
20A
Ignition coil
9
O2 SNSR
15A
Oxygen sensor
10
ENG SNSR
15A
Power train control system sensors
11
HORN
15A
Horn
12
TAIL LP
20A
Tail light
13
H/LP WASHER
20A
Headlight washer
14
ETS
20A
Electronic throttle system
15
FOG LP (FR)
15A
Fog light (front)
16
H/LP (HI)
15A
Headlight (high)
17
SPARE
30A
spare fuse
18
SPARE
20A
spare fuse
19
SPARE
15A
spare fuse
20
SPARE
10A
spare fuse
21
BLOWER MTR
30A
Blower motor
22
S/WARMER
30A
Seat warmer
23
AMP
20A
Radio amplifier
24
DRL*
15A
Daytime running light
Description
Fuse rating
Protected component
25
H/LP (LO-RH)
15A
Headlight (low beam-right)
26
P/FUSE-1
30A
All electrical system
27
ECU
10A
Engine control unit
28
ECS
15A
Electronic control suspension
!
NOT USED
Not used
C/FAN
20A
Condenser fan
P/SEAT (FR)
30A
Power seat (front)
IGN SW-1
30A
Ignition switch
ABS 2
30A
Anti-lock brake system
ABS 1
30A
Anti-lock brake system
IGN SW-2
30A
Ignition switch
R/FAN
30A
Radiator fan
H/LP (LO-LH)
-
Headlight relay (low beam-left)
FUEL PUMP
-
Fuel pump relay
HORN
-
Horn relay
START
-
Start motor relay
A/CON
-
Air conditioner relay
A/CON FAN-1
-
Air conditioner fan relay
H/LP (HI)
-
Headlight relay (high beam)
R/FAN
-
Radiator fan relay
FOG LP (FR)
-
Fog light relay (front)
TAIL LP
-
Taillight relay
WIPER (LO)
-
Wiper relay (low)
A/CON FAN-2
-
Air conditioner fan relay
Engine compartment
6 13
In case of an emergency
1
2
3
4
5
6
7
8
9
Driver-side knee bolster
Description
Fuse rating
Protected component
B/ALARM
10A
Burglar alarm
A/BAG
15A
Airbag
C/LIGHTER
20A
Cigar lighter
S/WARMER
10A
Seat warmer
P/WDW(RH)
20A
Power window (right)
P/HANDLE
15A
Power steering wheel
T/SIG LP
15A
Turn signal light
HTD GLASS
30A
Defroster
TRUNK OPEN
15A
Trunk lid opener
CLUSTER
10A
Cluster
A/BAG IND
10A
Airbag indicator
P/OUTLET
20A
Electrical power socket
LAN UNIT
10A
Lan unit
CURTAIN(RR)
10A
Electric curtain (rear)
FOG LP(RR), PIC
15A
Fog light (rear), Personal identifi-
cation card
F/LID OPEN
15A
Fuel filler lid opener
P/SEAT(RR)
30A
Power seat (rear)
B/ALARM
10A
Burglar alarm
STOP LP
15A
Stop light
TRIP COMPUTER
10A
Trip computer
B/UP LP
10A
Back-up light
AV
10A
Audio
H/LP
10A
Headlight
Description
Fuse rating
Protected component
A/CON
10A
Air-conditioning system
P/WDW(LH)
20A
Power window (left)
TAIL LP(RH)
10A
Taillight (right)
BACK WARN’G
10A
Back warning
DR LP
10A
Door courtesy lamp
MIRROR HTD
10A
Outside review mirror defroster
ENG SNSR
10A
Power train control system sensors
T/REDUCER
10A
Seat belt tension reducer
CLOCK
10A
Clock
WIPER(FR)
20A
Wiper (front)
EPS
10A
Electronic power steering
TAIL LP(LH)
10A
Tail light (left)
ROOM LP
10A
Room lamp
AV, CLOCK
15A
Audio, Clock
LAN UNIT
10A
Lan unit
SHUNT CONN
-
Switch illumination
POWER/CONN
-
Power connector
In case of an emergency
14
6
1
2
3
4
5
6
7
8
9
Power connector
Your vehicle is equipped with a
power connector to prevent battery
discharge if your vehicle is parked
without being operated for prolonged
periods. Use the following proce-
dures before parking the vehicle for
prolonged period.
1. Turn off the engine.
2. Turn off the headlights and tail
lights.
3. Open the driver-side knee bolster
cover
and
pull
up
the
“POWER/CONN”.
NOTICE
If the power connector is pulled up
from the fuse panel, the warning
chime, AV system, clock and
intetrior lamps, etc., will not oper-
ate. Some items must be reset after
replacement. (Refer to “Items to
be reset···.” on page 7-33)
Even though the power connector
is pulled up, the battery can still
be discharged by operation of the
headlights or other electrical
devices.
1GHA403
Power
connector