Kia Sedona - 2008 Fuse Box Diagram

Kia Sedona - 2008 Fuse Box Diagram

3 19
Features of your vehicle
How to reset the power sliding door
and power tailgate
If the battery has been discharged or dis-
connected, the related fuse has been
replaced or disconnected, and the power
sliding door or power tailgate doesn't
work properly, the power sliding door and
power tailgate must be reset as follows:
1. Put the shift lever in the P (Park) for
automatic transaxle.
2. Close the sliding door's windows and
fuel filler lid.
3. Pull the SHUNT connector on the dri-
ver's side fuse panel and reinstall it
after 1 minute.
4. Close the sliding door or tailgate man-
ually.
5. Open the sliding door or tailgate com-
pletely using the transmitter or main
control button on the overhead con-
sole.
6. Close the sliding door or tailgate com-
pletely using the transmitter or main
control button on the overhead con-
sole.
For the left/right power sliding doors and
power tailgate, follow above steps to
reset.
If the power sliding door or power tailgate
doesn't work properly after above proce-
dure, have the system checked by an
authorized Kia dealer.
WARNING
• Never intentionally place any
object or part of your body in the
path of the power sliding door or
power tailgate to make sure the
automatic stop operates.
• Make sure rear passengers are
seated and there are no people or
objects around the door before
operating the power sliding door.
Make sure all faces, arms, hands,
body parts and any other obstruc-
tions are safely out of the way
before operating the power slid-
ing doors or power tailgate.
Never place any object or part of
your body in the path of the
power sliding door or power tail-
gate. This could result in serious
injury or cause damage to the
vehicle.
Make sure there are no people or
objects around the door before
operating the power sliding door
or power tailgate. Have rear pas-
sengers or cargo get in or out of
the vehicle after the door is open
fully and stopped.
1VQA4005
On the driver’s side fuse panel
3 27
Features of your vehicle
The ignition switch must be in the ON
position for power windows to operate.
Each door has a power window switch
that
controls
that
door’s
window.
However, the driver has a power window
lock switch which can block the operation
of passenger windows.
The power windows can be operated for
approximately 30 seconds after the igni-
tion key is removed or turned to the ACC
or LOCK position. However, if the front
doors are opened, the power windows
cannot be operated even within the 30
seconds after the ignition key removal.
While driving, if you notice buffeting and
pulsation (wind shock) with either side
window open, you should open the oppo-
site window slightly to reduce the condi-
tion.
Window opening and closing
The driver’s door has a master power
window switch that controls all the win-
dows in the vehicle.
To open or close a window, press down
(8) or pull up (8) the front portion of the
corresponding switch.
• To open or close a rear quarter win-
dow, push (8) the corresponding
switch.
(Continued)
• Never try to operate the main
switch on the driver's door and
the
individual
door
window
switch in opposing directions at
the same time. If this is done, the
window will stop and cannot be
opened or closed.
WARNING -
Windows
• Always double check to make
sure all arms, hands, head and
other obstructions are safely out
of the way before closing a win-
dow.
Do not allow children to play with
the power windows. Keep the dri-
ver’s door power window lock
switch in the LOCK position
(depressed). Serious injury can
result from unintentional window
operation by the child.
• Do not extend face or arms out-
side through the window opening
while driving.
CAUTION
• To prevent the power window
system from the possibility of
damage, do not open or close two
windows at the same time. This
will also ensure the longevity of
the fuse.
(Continued)
Features of your vehicle
176
3
(1) : It can be used when the ignition
switch is in ACC or ON position.
(2), (3) : It can be used regardless of the
ignition switch position.
Power outlet
The power outlets are designed to pro-
vide power for mobile telephones or
other devices designed to operate with
vehicle electrical systems. The devices
should draw less than 10 amps with the
engine running.
Digital clock
Whenever the battery terminals, related
fuses are disconnected, you must reset
the time.
When the ignition switch is in the ACC or
ON position, the clock buttons operate as
follows:
CAUTION
• Use power outlet only when the
engine is running and remove the
accessory plug after use. Using
the accessory plug for prolonged
periods of time with the engine
off could cause the battery to dis-
charge.
Only use 12V electric accessories
which are less than 10A in elec-
tric capacity.
• Adjust the air-conditioner or
heater to the lowest operating
level when using the power outlet.
Close the cover when not in use.
• Some electronic devices can
cause
electronic
interference
when plugged into a vehicle’s
power outlet. These devices may
cause excessive audio static and
malfunctions in other electronic
systems or devices used in your
vehicle.
OVQ038092N
3 187
Features of your vehicle
6. CD EJECT Button
When the
button is pressed with a CD
loaded, the CD will eject.
Forcing to eject : To force to eject a CD,
press this button for more than 3 sec-
onds.
(Do this only when a CD is jammed and
you can not eject it in the normal way -
e.g.) in case that you have inserted 2
CDs by mistake)
7
. RANDOM (RDM) Button
With random, you can listen to the tracks
in random, rather than sequential order.
To use random, do the following:
Press the RDM button to listen to record-
ed tracks in random sequence. Press
RDM again to cancel or turn the power
OFF then ON.The unit defaults to playing
tracks in sequential order.
NOTICE
To assure proper operation of the unit,
keep the vehicle interior temperature
within a normal range by using the
vehicle's air conditioning or heating
system.
• When replacing the fuse, replace it
with a fuse having the correct capaci-
ty.
• All stored bookmarks are all erased
when the car battery is disconnected
or power to the vehicle is lost. If this
occurs, the bookmarks will have to be
reset.
This equipment is designed to be used
only in a 12 volt DC battery system
with negative ground.
• This unit is made of precision parts.
Do not attempt to disassemble or
adjust any parts.
When driving your vehicle, be sure to
keep the volume of the unit set low
enough to allow you to hear sounds
coming from the outside.
Do not expose this equipment (includ-
ing the speakers and CD) to water or
excessive moisture.
NOTICE
Do not insert warped or poor quality
discs into the CD player as damage to
the unit may occur.
Do not insert anything like coins into
the player slot as damage to the unit
may occur.
• Do not place beverages close to the
audio system. The playback mecha-
nism may be damaged if you spill
them.
• Do not strike or allow anything to
impact the audio system, damage to
the system mechanisms could occur.
• Off-road or rough surface driving
may cause the compact disc to skip.
Do not use the compact disc when
driving in such conditions as damage
to the compact disc face could occur.
• Do not attempt to grab or pull the
compact disc out while the disc is
being pulled into the audio unit by the
self-loading mechanism.
Damage to
the audio unit and compact disc could
occur.
Avoid using recorded compact discs in
your audio unit.
Original compact
discs are recommended for
best
results.
Features of your vehicle
194
3
10. CD SCAN Button
• To playback the first 10 seconds of
each track, press the CD SCAN button
more than 0.8 seconds.
• To playback the first 10 seconds of
each track in the selected folder, press
the CD SCAN button within 0.8 sec-
onds. (MP3 CD only)
Press the CD SCAN button again with-
in 10 sec. when you have reached the
desired track.
11. FILE SEARCH Knob
(TUNE Select Knob)
You can skip the track (file) by turning
the FILE SEARCH knob clockwise or
counterclockwise.
After selecting the desired track (file),
press the FILE SEARCH knob to play-
back the track (file).
If you do not press the FILE SEARCH
knob within five seconds, the search
will stop.
12. FOLDER SEARCH (FLDR)
Button
• You can move through the folder by
pushing the FLDR button to up (
)
and down(
).
After moving the desired folder, press
the FILE SEARCH knob to play back in
the selected folder. If you do not press
the FILE SEARCH knob within 5 sec-
onds, the folder searching function will
be released. It can not be operated in a
single folder.
13. INFO Button
While playing CD(MP3), If this button is
pressed repeatedly, the played file infor-
mation will be displayed in the following
order.
FILE NAME
SONG TITLE
ARTIST
NAME
ALBUM TITLE
FOLDER
NAME
TOTAL
FILE
MARK
ADDRESS
FILE NAME
“NO DATA” wil be displayed in case that
there is no information on the selected
item.
NOTICE
To assure proper operation of the unit,
keep the vehicle interior temperature
within a normal range by using the
vehicle's air conditioning or heating
system.
• When replacing the fuse, replace it
with a fuse having the correct capacity.
• All stored bookmarks are all erased
when the car battery is disconnected
or power to the vehicle is lost.
If this
occurs, the bookmarks will have to be
reset.
This equipment is designed to be used
only in a 12 volt DC battery system
with negative ground.
• This unit is made of precision parts.
Do not attempt to disassemble or
adjust any parts.
When driving your vehicle, be sure to
keep the volume of the unit set low
enough to allow you to hear sounds
coming from the outside.
Do not expose this equipment (includ-
ing the speakers and tape) to water or
excessive moisture.
3 203
Features of your vehicle
12. DISC UP/DOWN Button
• By
pressing
"DISC
"/"DISC
"
while CD changer is playing you can
move backward or forward to the next
disc
and
playback
automatically
begins.
If any of the slots do not contain a CD,
your car audio will skip the empty slot
and play only those that contain a CD.
When switching CD’s, the LCD dis-
plays the selected CD’s number.
13. FILE SEARCH Knob
(TUNE Select Knob)
You can skip the track (file) by turning
the FILE SEARCH knob clockwise or
counterclockwise.
After selecting the desired track (file),
press the FILE SEARCH knob to play-
back the track (file).
If you do not press the FILE SEARCH
knob within five seconds, the search
will stop.
14. FOLDER SEARCH (FLDR)
Button
• You can move through the folder by
pushing the FLDR button to up (
)
and down(
).
After moving the desired folder, press
the FILE SEARCH knob to play back in
the selected folder. If you do not press
the FILE SEARCH knob within 5 sec-
onds, the folder searching function will
be released. It can not be operated in a
single folder.
15. INFO Button
While playing CD(MP3), If this button is
pressed repeatedly, the played file infor-
mation will be displayed in the following
order.
FILE NAME
SONG TITLE
ARTIST
NAME
ALBUM TITLE
FOLDER
NAME
TOTAL
FILE
MARK
ADDRESS
FILE NAME
“NO DATA” wil be displayed in case that
there is no information on the selected
item.
NOTICE
To assure proper operation of the unit,
keep the vehicle interior temperature
within a normal range by using the
vehicle's air conditioning or heating
system.
• When replacing the fuse, replace it
with a fuse having the correct capaci-
ty.
Stored bookmarks are all erased when
the car battery is disconnected or
power to the vehicle is lost. If this
occurs, the bookmarks will have to be
reset.
This equipment is designed to be used
only in a 12 volt DC battery system
with negative ground.
• This unit is made of precision parts.
Do not attempt to disassemble or
adjust any parts.
When driving your vehicle, be sure to
keep the volume of the unit set low
enough to allow you to hear sounds
coming from the outside.
Do not expose this equipment (includ-
ing the speakers and tape) to water or
excessive moisture.
3 223
Features of your vehicle
Troubleshooting
Problem
Possible causes / solutions
Press the STOP/EJECT button to release the disc. The player will attempt to eject the disc
up to three times before performing the Auto-Reload function. Once the Auto-Reload func-
tion is complete, press the STOP/EJECT button again to release the disc from the player.
If a disc is still stuck or blocked in the RSE unit, turn the ignition off and then on again to reset
the RSE unit.
Verify that the headphone is equipped with batteries, and that the batteries are charged.
Insert or replace 2 AAA batteries to resume headphone function.
If the display does not show “NO DISC”, then there is no power. Check the vehicle fuse. If the
RSE still does not work, contact your authorized Kia dealer.
Make sure you are pointing the remote control at the face of the RSE at a 45° angle. Change
the battery. [Device requires one (1) CR2025 battery.] Use the control buttons on the RSE
display panel. If the remote control still does not work, contact your authorized Kia dealer.
Invalid button press. The function you are trying to perform is not available.
The disc becomes stuck or
blocked.
There is no audio in the head-
phones.
The RSE does not work.
The remote control does not
work.
Continue receiving an invalid
icon[
:
]
when a button is
pressed
6
Maintenance services / 6-2
Maintenance schedule / 6-3
Owner maintenance / 6-7
Engine compartment / 6-9
Engine oil / 6-10
Engine coolant / 6-11
Air cleaner / 6-13
Automatic transaxle / 6-13
Brakes / 6-15
Lubricants and fluids / 6-16
Power steering / 6-17
Climate control air filter / 6-17
Wiper blades / 6-18
Fuses / 6-20
Battery / 6-28
Tires and wheels / 6-30
Lubricant / 6-42
Appearance care / 6-43
Emission control system / 6-46
Maintenance
6 9
Maintenance
ENGINE COMPARTMENT
OVQ068001N
1. Engine coolant reservoir
2. Engine oil filler cap
3. Brake fluid reservoir
4. Air cleaner
5. Fuse box
6. Negative battery terminal
7. Positive battery terminal
8. Auto transaxle oil dipstick
9. Radiator cap
10. Engine oil dipstick
11. Power steering fluid reservoir
12. Windshield washer fluid reservoir
* The actual engine room in the vehicle may differ from the illustration.
Maintenance
20
6
FUSES
A vehicle’s electrical system is protected
from electrical overload damage by
fuses.
This vehicle has three fuse panels, one
located in the driver’s side panel bolster,
another in the cargo area, the other in
the engine compartment near the bat-
tery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check the
appropriate circuit fuse. If a fuse has
blown, the element inside the fuse will be
melted.
If the electrical system does not work,
first check the driver’s side fuse panel.
Always replace a blown fuse with one of
the same rating.
If the replacement fuse blows, this indi-
cates an electrical problem. Avoid using
the system involved and immediately
consult an Authorized Kia Dealer.
Three kinds of fuses are used: blade type
for lower amperage rating and cartridge
type, fusible link for higher amperage rat-
ings.
Fuse replacement
1VQA4037
Normal
Normal
Blade type
Cartridge type
Fusible link
Blown
Blown
Normal
Blown
WARNING
- Fuse replace-
ment
• Never replace a fuse with any-
thing but another fuse of the
same rating.
• A higher capacity fuse could
cause damage possibly a fire.
Never install a wire instead of the
proper fuse - even as a temporary
repair. It may cause extensive
wiring damage and possibly a fire.
CAUTION
Do not use a screwdriver or any
other metal object to remove fuses
because it may cause a short circuit
and damage the system.
6 21
Maintenance
Engine compartment
1. Turn the ignition switch and all other
switches off.
2. Remove the fuse box cover by press-
ing the tap and pulling up.
3. Check the removed fuse; replace it if it
is blown. To remove or insert the fuse,
use the fuse puller in the main fuse
box in the engine compartment.
4. Push in a new fuse of the same rating,
and make sure it fits tightly in the clips.
If it fits loosely, consult an Authorized Kia
Dealer.
Inner panel
1. Turn the ignition switch and all other
switches off.
2. Open the fuse panel cover.
1VQA4006
CAUTION
After checking the fuse box in the
engine
compartment,
securely
install the fuse box cover.
If not,
electrical failures may occur from
water leaking in.
1VQA4002
OVQ066016N
Driver’s side panel
Rear cargo area panel
Maintenance
22
6
3. Pull the suspected fuse straight out.
Use the removal tool provided on the
main fuse box in the engine compart-
ment.
4. Check the removed fuse; replace it if it
is blown.
Spare fuses are provided in the main
fuse box in the engine compartment.
5. Push in a new fuse of the same rating,
and make sure it fits tightly in the clips.
If it fits loosely, consult an Authorized Kia
Dealer.
If you do not have a spare, use a fuse of
the same rating from a circuit you may
not need for operating the vehicle, such
as the cigar lighter fuse.
If the headlights or other electrical com-
ponents do not work and the fuses are
OK, check the fuse block in the engine
compartment. If a fuse is blown, it must
be replaced.
Main fuse
If the main fuse is blown, it must be
removed as follows:
1. Disconnect the negative battery cable.
2. Remove the nuts shown in the picture
above.
3. Replace the fuse with a new one of the
same rating.
4. Reinstall in the reverse order of
removal.
NOTICE
If the main fuse is blown, consult an
Authorized Kia Dealer.
1VQA4008
1VQA4004
6 23
Maintenance
Fuse/Relay panel description
Inside the fuse/relay box covers, you can find the fuse/relay label describing fuse/relay
name and capacity.
Driver’s side panel
Engine compartment
OVA067012/OVQ067017N/OVQ067104N/OVQ046010N
Rear cargo area panel
Maintenance
24
6
Driver's side fuse panel
Description
Fuse rating
Protected component
AUDIO
15A
Audio, Step lamp
MEMORY
7.5A
Climate control module, Clock, Cluster, Trip computer, Front area module, Power sliding door module, Power
tailgate module, Driver's door module, Front passenger door module, Driver's power seat module,
Driver position memory system unit
VRS
10A
Variable rack stroke system module, Variable rack stroke system control button
IG2-1
7.5A
Air conditioner control module, Multi function switch, Inside relay box, ECM mirror, Rain sensor, Seat Warmer
IG2-2
7.5A
Rear climate control button, Front area module, Power sliding door module, Power tailgate module, Driver's door
module, Front passenger door module, Driver's power seat module, Driver position memory system unit
OBD-II
7.5A
OBD-II, Diagonosis connector
ROOM
7.5A
Vanity mirror, Map lamp, Overhead console, Room lamp switch, Climate control module, Homelink
K/LOCK
7.5A
Key interlock solenoid
ILLUMI
7.5A
Instrument panel illumination
AMP
25A
Amplifier
SEAT WARMER
20A
Inside relay box(Seat warmer)
SUNROOF
25A
Sunroof module
DDM
30A
Driver's door module
TPMS
7.5A
Tire pressure monitoring system
PEDAL
15A
Power adjustable pedal relay(None-driver position memory system only)
P/OUTLET 1
15A
Power outlet(Front)
ASS P/SEAT
20A
Front passenger's power seat module
DRV P/SEAT
30A
Driver's power seat module
ADM
30A
Front passenger door module
ACC
7.5A
Audio, Clock, Outside rearview mirror control and folding switch
P/OUTLET 2
15A
Cigar lighter, Power outlet
START
7.5A
Start relay
AIRBAG IND
7.5A
Cluster
6 25
Maintenance
Description
Fuse rating
Protected component
ENG
7.5A
Automatic shift lever switch, Vehicle speed sensor, Inhibitor switch, Transaxle control module,
Input speed sensor, Output speed sensor, Back-up lamp switch, Fuel filter
IG1
7.5A
Trip computer, Buzzer(Back warning system), Cluster, ESC switch, Ambient temperature sensor, Generator
ABS
7.5A
ABS control module, ESC control module, Yaw rate sensor, Steering angle sensor
AIRBAG
15A
Air bag control module
ALTERNATOR
-
Generator relay
SHUNT
-
Shunt connector
Description
Fuse rating
Protected component
RR D/LOCK
20A
Sliding door lock relay, Sliding door unlock relay, Sliding door lock actuator, Tailgate lock actuator
RR WIPER
15A
Rear wiper relay, Rear wiper motor
RR DEFOG
25A
Rear window defroster relay, Rear window defroster
POWER TAIL GATE
30A
Power tailgate module
P/QUARTER
10A
Power rear quarter glass open relay, Power rear quarter glass close relay, Power rear quarter glass motor
RR P/WIN-RH
25A
Sliding door power window relay(Right), Sliding door power window motor(Right)
RR P/WIN-LH
25A
Sliding door power window relay(Left), Sliding door power window motor(Left)
PSD-RH
30A
Power sliding door module(Right)
PSD-LH
30A
Power sliding door module(Left)
LUGGAGE
7.5A
Step lamp, Power tailgate ON/OFF switch, Tailgate lamp
FUEL DOOR
15A
Fuel filler lid relay, Fuel filler lid actuator
RR P/OTLT-LH
15A
Rear power outlet(Left)
RR P/OTLT-RH
15A
Rear power outlet(Right)
RR DEFOG RELAY
-
Rear window defroster relay
Rear cargo area panel
Maintenance
26
6
Description
Fuse rating
Protected component
P/TRAIN
7.5A
Theft alarm relay, Main relay,
TCM, Generator, ECM, Injector
15A, ECU 2 15A, ECU 1 10A,
Air conditioner compressor relay,
Inlet metering valve, EGR sole-
noid valve, Air flow sensor,
Diesel box, Immobilizer module
FUEL PUMP
15A
Fuel pump motor
SP
7.5A
Spare fuse
SP
10A
Spare fuse
SP
15A
Spare fuse
SP
20A
Spare fuse
SP
25A
Spare fuse
ABS 1
40A
ABS control module,
ESC control module
ABS 2
20A
ABS control module,
ESC control module
FRT WIPER
30A
Front wiper ON relay
KEY SW 2
30A
Start relay, IG2 Load(Variable
rack stroke, ECM mirror, Rain
sensor, Seat warmer)
RAM 1
50A
Rear area module
RAM 2
50A
Rear area module
RAM 3
50A
Rear area module
Engine compartment
Description
Fuse rating
Protected component
FRT/RR WASHER
10A
Front washer motor relay,
Rear washer motor relay
IG 2
7.5A
Fuel filter
STOP LAMP
20A
Stop lamp,
High mounted stop lamp
FUEL HEATER
20A
Fuel filter heater
KEY SW 1
25A
Instrument panel module
STOP SIGNAL
7.5A
TCU, PCU/ECU, ABS/ESC Unit
A/C COMP
7.5A
Air conditioner compressor relay
ATM
15A
ATM solenoid
FRT DEICER
15A
Front deicer
HORN
15A
Horn relay
ECU 1
10A
PCU/ECU, A/C comp relay, Mass
air flow sensor, Immobilizer unit
O2 DN
10A
O2 sensor(RL, RR)
ECU 2
15A
PCU/ECU, Oil control valve 1/2,
Variable intake manifold valve 1/2,
Canister purge solenoid valve,
Canister close valve,
Pulse width modulation relay
O2 UP
10A
O2 sensor(FL, FR)
IGN COIL
20A
Ignition coil 1/2/3/4/5/6, Condensor
INJECTOR
15A
PCU/ECU, Injector 1/2/3/4/5/6,
Glow relay 1/2, Intake manifold
valve, EGR Solenoid valve,
Cooling fan relay, Air flow sen-
sor, Intake throttle valve
6 27
Maintenance
Description
Fuse rating
Protected component
IPM 1
50A
Instrument panel module
IPM 2
50A
Instrument panel module
IPM 3
50A
Instrument panel module
FRT BLOWER
40A
Inside relay box(Front blower
relay)
RR BLOWER
30A
Inside relay box(Rear blower
relay)
IG 2 RELAY
-
Ignition relay
A/C COMP RELAY
-
Air conditioner compressor relay
MAIN RELAY
-
Main relay
START RELAY
-
Start relay
FUEL PUMP RELAY
-
Fuel pump relay
Engine compartment (main fuse)
Description
Fuse rating
Protected component
ALT
150A/200A
Generator
C/FAN
60A
Cooling fan
Maintenance
28
6
OVQ066018N
Shunt connector
Your vehicle is equipped with a shunt
connector to prevent battery discharge if
your vehicle is parked without being
operated for prolonged periods. Use the
following procedures before parking the
vehicle for prolonged periods.
1. Turn off the engine.
2. Turn off the headlights and tail lights.
3. Open the driver’s side panel cover and
pull up the shunt connector.
NOTICE
• If the shunt connector is pulled up
from the fuse panel, the warning
chime, audio, clock and interior
lamps, etc., will not operate. Some
items must be reset after replacement.
(Refer to “Items to be reset···.” on
page 6-30)
• Even though the shunt connector
is
pulled up, the battery can still be dis-
charged by operation of the head-
lights or other electrical devices.
1VQA4005
Shunt connector
BATTERY
WARNING
- Battery
dangers
Always read the following
instructions carefully when
handling a battery.
Keep lighted cigarettes and
all other flames or sparks
away from the battery.
Hydrogen, a highly com-
bustible gas,
is always
present in battery cells and
may explode if ignited.
(Continued)