Kia Sorento - 2011 Fuse Box Diagram

Kia Sorento - 2011 Fuse Box Diagram

3 45
Safety features of your vehicle
C040300AAM
Occupant Detection System
(ODS)
Your vehicle is equipped with an occu-
pant detection system in the front pas-
senger's seat.
The occupant detection system is
designed to detect the presence of a
properly-seated front passenger and
determine if the passenger's front air bag
should be enabled (may inflate) or not.
The driver's front air bag is not affected
or controlled by the occupant detection
system.
WARNING
• If an air bag deploys, there may
be a loud noise followed by a fine
dust released in the vehicle.
These conditions are normal and
are not hazardous - the air bags
are packed in this fine powder.
The dust generated during air
bag deployment may cause skin
or eye irritation as well as aggra-
vate asthma for some persons.
Always wash all exposed skin
areas thoroughly with lukewarm
water and a mild soap after an
accident in which the air bags
were deployed.
The SRS can function only when
the ignition switch is in the ON
position. If the SRS air bag warn-
ing light does not illuminate, or
continuously remains on after
illuminating for about 6 seconds
when the ignition switch is turned
to the ON position, or after the
engine is started, comes on while
driving, the SRS is not working
properly. If this occurs, have your
vehicle immediately inspected by
an authorized KIA dealer.
(Continued)
(Continued)
Before you replace a fuse or dis-
connect a battery terminal, turn
the ignition switch to the LOCK
position and remove the ignition
switch. Never remove or replace
the air bag related fuse(s) when
the ignition switch is in the ON
position. Failure to heed this
warning will cause the SRS air
bag warning light to illuminate.
WARNING
Do not put anything in front of the
passenger air bag
indicator.
OXM039052N
XM CAN (ENG) 3.QXP
11/26/2009
11:42 AM
Page 45
Features of your vehicle
24
4
D080104AAM
Power window lock button
The driver can disable the power win-
dow switches on the passenger doors
by pressing the power window lock but-
ton located on the driver’s door to the
LOCK position (pressed).
When the power window lock button
is in the LOCK position (pressed),
the driver’s master control cannot
operate the passenger door power
windows.
CAUTION
• To prevent possible damage to
the power window system, do not
open or close two windows or
more at the same time. This will
also ensure the longevity of the
fuse.
• Never try to operate the main
switch on the driver's door and
the
individual
door
window
switch in the opposite directions
at the same time. If this is done,
the window will stop and cannot
be opened or closed.
WARNING -
Windows
• NEVER leave the ignition key in
the vehicle.
NEVER leave any child unattend-
ed in the vehicle.
Even very
young children may inadvertently
cause the vehicle to move, entan-
gle themselves in the windows,
or otherwise injure themselves or
others.
• Always double check to make
sure all arms, hands, head and
other obstructions are safely out
of the way before closing a win-
dow.
Do not allow children to play with
the power windows. Keep the dri-
ver’s door power window lock
button in the LOCK position
(pressed).
Serious injury can
result from unintentional window
operation by the child.
• Do not extend heads or any
limbs outside the window while
the vehicle is in motion.
OXM049018
XM CAN (ENG) 4(~101).QXP
4/14/2010
10:39 AM
Page 24
5 11
Driving your vehicle
NOTICE
If the battery is weak or the smart key
does not work correctly, you can start
the engine by inserting the smart key
in the smart key holder. When you
pull out the smart key from the smart
key holder, press the smart key and
pull it out.
(Continued)
(Continued)
When the stop lamp fuse is blown, you
can't start the engine normally.
Replace the fuse with a new one. If it
is not possible, you can start the
engine by pressing the ENGINE
START/STOP button for 10 seconds
while it is in the ACC position. The
engine can start without depressing
the brake pedal. But for your safety
always depress the brake pedal before
starting the engine.
CAUTION
Do not press the ENGINE START/
STOP button for more than 10 sec-
onds except when the stop lamp
fuse is blown.
OXM059008
XM CAN (ENG) 5.qxp
11/26/2009
12:01 PM
Page 11
7
Engine compartment / 7-2
Maintenance services / 7-4
Owner maintenance / 7-5
Explanation of scheduled maintenance items / 7-11
Engine oil / 7-14
Engine coolant / 7-15
Brake/clutch fluid / 7-18
Power steering fluid / 7-19
Washer fluid / 7-20
Parking brake / 7-20
Air cleaner / 7-21
Climate control air filter / 7-23
Wiper blades / 7-25
Battery / 7-29
Tires and wheels / 7-32
Fuses / 7-45
Appearance care / 7-54
Emission control system / 7-60
Maintenance
XM CAN (ENG) 7.qxp
4/14/2010
10:55 AM
Page 1
Maintenance
2
7
ENGINE COMPARTMENT
G010000AAM-EU
OXM079001N
1. Engine Coolant Reservoir
2.Windshield Washer Fluid Reservoir
3. Power Steering Fluid Reservoir*
4. Radiator Cap
5. Engine Oil Filler Cap
6. Engine Oil Dipstick
7. Brake Fluid Reservoir
8. Air Cleaner
9. Fuse Box
10. Negative Battery Terminal
11. Positive Battery Terminal
* if equipped
The actual engine compartment in the vehicle may differ from the illustration.
2.4L
XM CAN (ENG) 7.qxp
4/14/2010
10:56 AM
Page 2
7 3
Maintenance
OXM079100
1. Engine coolant reservoir
2. Engine oil filler cap
3. Brake fluid reservoir
4. Air cleaner
5. Fuse box
6. Negative battery terminal
7. Positive battery terminal
8. Radiator cap
9. Engine oil dipstick
10. Power steering fluid reservoir*
11. Windshield washer fluid reservoir
* if equipped
3.5L
The actual engine compartment in the vehicle may differ from the illustration.
XM CAN (ENG) 7.qxp
4/14/2010
10:56 AM
Page 3
7 45
Maintenance
FUSES
G210000AAM
A vehicle’s electrical system is protected
from electrical overload damage by
fuses.
This vehicle has 2 fuse panels, one locat-
ed in the driver’s side panel bolster, the
other in the engine compartment near
the battery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check the
appropriate circuit fuse. If a fuse has
blown, the element inside the fuse will
melt.
If the electrical system does not work,
first check the driver’s side fuse panel.
Always replace a blown fuse with one of
the same rating.
If the replacement fuse blows, this indi-
cates an electrical problem. Avoid using
the system involved and immediately
consult an authorized KIA dealer.
Three kinds of fuses are used: blade type
for lower amperage rating, cartridge type,
and multi fuse for higher amperage rat-
ings.
WARNING
- Fuse replace-
ment
• Never replace a fuse with any-
thing but another fuse of the
same rating.
• A higher capacity fuse could
cause damage and possibly a
fire.
Never install a wire instead of the
proper fuse - even as a temporary
repair. It may cause extensive
wiring damage and a possible fire.
CAUTION
Do not use a screwdriver or any
other metal object to remove fuses
because it may cause a short circuit
and damage the system.
OBK079042
Normal
Normal
Blade type
Cartridge type
Multi fuse
Blown
Blown
Normal
Blown
XM CAN (ENG) 7.qxp
4/14/2010
10:59 AM
Page 45
Maintenance
46
7
G210100AAM
Inner panel fuse replacement
1. Turn the ignition switch and all other
switches off.
2. Open the fuse panel cover.
3. Pull the suspected fuse straight out.
Use the removal tool provided on the
engine compartment fuse panel cover.
4. Check the removed fuse; replace it if it
is blown.
Spare fuses are provided in the engine
compartment fuse panel.
5. Push in a new fuse of the same rating,
and make sure it fits tightly in the clips.
If it fits loosely, consult an authorized KIA
dealer.
If you do not have a spare, use a fuse of
the same rating from a circuit you may
not need for operating the vehicle, such
as the power outlet fuse.
If the headlights or other electrical com-
ponents do not work and the fuses are
OK, check the fuse panel in the engine
compartment. If a fuse is blown, it must
be replaced.
OXM079021
OXM079020
XM CAN (ENG) 7.qxp
4/14/2010
10:59 AM
Page 46
7 47
Maintenance
G210101AHM-C1
Memory fuse
Your vehicle is equipped with a memory
fuse to prevent battery discharge if your
vehicle is parked without being operated
for prolonged periods. Use the following
procedures before parking the vehicle for
prolonged periods.
1. Turn off the engine.
2. Turn off the headlights and tail lights.
3. Open the driver’s side panel cover and
pull out the memory fuse.
NOTICE
If the memory fuse is pulled out from
the fuse panel, the warning chime,
audio, clock and interior lamps, etc.,
will not operate. Some items must be
reset after
replacement. Refer
to
“Battery” in this section.
• Even though the memory fuse is
pulled out, the battery can still be dis-
charged by operation of the head-
lights or other electrical devices.
G210200AHM
Engine compartment fuse
replacement
1. Turn the ignition switch and all other
switches off.
2. Remove the fuse panel cover by
pressing the tab and pulling the cover
up.
OXM079022
OXM079023
XM CAN (ENG) 7.qxp
4/14/2010
10:59 AM
Page 47
Maintenance
48
7
3. Check the removed fuse; replace it if it
is blown. To remove or insert the fuse,
use the fuse puller in the engine com-
partment fuse panel.
4. Push in a new fuse of the same rating,
and make sure it fits tightly in the clips.
If it fits loosely, consult an authorized
KIA dealer.
G210201AAM
Multi fuse
If the multi fuse is blown, it must be
removed as follows:
1. Turn off the engine.
2. Disconnect the negative battery cable.
3. Remove the fuse panel on the right
side in the engine compartment.
4. Remove the nuts shown in the picture
above.
5. Replace the fuse with a new one of the
same rating.
6. Reinstall in the reverse order of
removal.
NOTICE
If the multi fuse is blown, consult an
authorized KIA dealer.
CAUTION
After checking the fuse panel in the
engine
compartment,
securely
install the fuse panel cover. If not,
electrical failures may occur from
water contact.
OXM079025
XM CAN (ENG) 7.qxp
4/14/2010
10:59 AM
Page 48
7 49
Maintenance
NOTICE
Not all fuse panel descriptions in this
manual may be applicable to your vehi-
cle. It is accurate at the time of printing.
When you inspect the fuse panel in your
vehicle, refer to the fuse panel label.
G210300AAM-EU
Fuse/relay panel description
Inside the fuse/relay panel covers, you can find the fuse/relay label describing fuse/relay name and capacity.
Inner fuse panel
Engine compartment fuse panel
OXM079026/OXM079027
XM CAN (ENG) 7.qxp
4/14/2010
10:59 AM
Page 49
Maintenance
50
7
Inner fuse panel
Description
Fuse rating
Protected component
MODULE 2
10A
Instrument Cluster (IND./MICOM), Tire Pressure Monitoring Module, Audio, Multifunction Switch (Remocon),
Rear Parking Assist Buzzer ICM Relay Box (DBC Relay), ESC Off Switch, DBC Switch, Steering Angle
Sensor, Alternator, Smart Key Control Module A/V & Navigation Head Unit, Rear Monitor, IPM (BCM IG1)
MODULE 1
10A
Smart Key Control Module, Rear Parking Assist Control Module E/R Fuse & Relay Box (Fuse - B/UP LP,
ABS, ECU 2), PDM, 4WD ECM
RPAS
7.5A
Rear Parking Assist Switch
A/BAG IND
10A
Instrument Cluster (IND.), PODS Module, Digital Clock
A/BAG
15A
SRS Control Module
START
7.5A
E/R Fuse & Relay Box (Relay - Start, Sub Start, Burglar Alarm), PDM
WIPER RR
15A
ICM Relay Box (Rear Wiper Relay), Rear Wiper Motor
Rear Wiper Switch, Rear Washer Switch
WIPER FRT
25A
E/R Fuse & Relay Box (Wiper (Low) Relay), Front Wiper Motor, Multifunction Switch (Wiper)
AUDIO 2
7.5A
AMP, Power Outside Mirror Switch, Smart Key Control Module, PDM, Audio, A/V & Navigation Head
Unit, Digital Clock, IPM (BCM ACC), DVD Player Can, Rear Monitor
P/OUTLET RR
15A
Rear Power Outlet
P/OUTLET FRT
25A
Driver/Passenger Power Outlet
MODULE 3
7.5A
Not Used
A/CON
7.5A
Front A/C Control Module, Active Incar Sensor, Cluster Ionize, PDM, ICM Relay Box (Front Seat Warmer
Relay, Rear A/C Relay) E/R Fuse & Relay Box (Blower Relay), Sunroof Motor, Electro Chromic Mirror,
IPM (BCM IG2)
AMP
30A
AMP
DRL
7.5A
Ground (GE01)
A/CON MANU
7.5A
PCM, Front Blower Resistor, Front A/C Control Module
A/CON AUTO
7.5A
Front A/C Control Module
XM CAN (ENG) 7.qxp
4/14/2010
10:59 AM
Page 50
7 51
Maintenance
Description
Fuse rating
Protected component
B/A HORN
10A
Burglar Alarm Horn Relay
A/CON REAR
20A
ICM Relay Box (Rear A/C Relay)
P/WDW LH
25A
Driver Power Window Relay, Power Window Main Switch, Rear Power Window Switch LH, Driver Safety
Power Window Module
P/WDW RH
25A
Passenger Power Window Relay, Power Window Main Switch
Passenger Power Window Switch, Rear Power Window Switch RH
MODULE
15A
Audio, A/V & Navigation Head Unit, RF Receiver, IPM (BCM B+), Rear Monitor
ROOM LP
10A
Instrument Cluster (IND.), Digital Clock, Front A/C Control Module Data Link Connector, Door Warning
Switch, Personal Room Lamp Room Lamp Auto Cut Relay, Overhead Console (MAP Lamp) Room
Lamp, Cargo Lamp, Driver/Passenger Vanity Lamp Electro Chromic Mirror
DOOR LP
10A
Driver/Passenger Door Scuff Lamp, DVD Player Can
DR LOCK
20A
Door Lock/Unlock Relay, ICM Relay Box (Two Turn Unlock Relay)
Driver/Passenger Door Lock Actuator, Rear Door Lock Actuator LH/RH
PDM
20A
PDM
SUNROOF
20A
Sunroof Motor
SMART KEY
10A
PDM, Smart Key Control Module, Start Stop Button Switch, FOB Holder, Key Solenoid
S/HTR FRT
20A
ICM Relay Box (Front Seat Warmer Relay)
P/SEAT
30A
Driver Power Seat Switch, Driver Lumbar Support Switch
4WD
10A
4WD ECM, Sport Mode Switch
HAZARD
15A
IPM (Flasher Unit)
F/LID
15A
Tail Gate Relay, Tail Gate Actuator, Fuel Filler Door Switch
TPMS
10A
Tire Pressure Monitoring Module
HTD MIRR
10A
Driver/Passenger Power Outside Mirror, Front A/C Control Module
POWER CONNECTOR
FUSE - MODULE, ROOM LP, DOOR LP
XM CAN (ENG) 7.qxp
4/14/2010
11:00 AM
Page 51
Maintenance
52
7
Engine compartment fuse panel
Description
Fuse rating
Protected component
ALT
175A
Alternator
MULTI
FUSE
I/P B+2
60A
IPM (Fuse - S/HTR FRT, P/SEAT, Power Connector - MODULE, ROOM LP DOOR LP)
BLOWER
40A
Blower Relay
RR HTD
40A
Rear Defogger Relay
ABS 1
40A
ESC Control Module, Multipurpose Check Connector
ABS 2
40A
ESC Control Module, Multipurpo se Check Connector
I/P B+3
60A
IPM (Fuse - HAZARD, TPMS, F/LID)
I/P B+1
60A
IPM (Fuse - DR LOCK, SUNROOF, 4WD, PDM, SMART KEY)
FUSE
IGN 2
40A
Start Relay, W/O Smart Key - Ignition Switch, With Smart Key - PDM Relay Box (IGN2 Relay)
TRAILER
30A
Trailer Power Outlet
IGN 1
30A
W/O Smart Key - Ignition Switch, With Smart Key - PDM Relay Box (IGN1 Relay)
HORN
15A
Horn Relay
STOP LP
15A
Stop Lamp Switch, ICM Relay Box (DBC Relay)
B+ SENSOR
15A
Battery Sensor
DEICER
15A
Front Wiper Deicer Relay
C/FAN
50A
Cooling Fan Relay Low/High
I/P B+4
50A
IPM (Fuse - P/WDW LH, P/WDW RH, B/A HORN, A/CON REAR, AMP)
ECU 2
7.5A
Sub Start Relay, PCM, Transaxle Range Switch, Alternator (G6DC)
ABS
7.5A
ESC Control Module, Multipurpose Check Connector, Stop Lamp Switch (G4KE)
B/UP LP
7.5A
Back-Up Lamp Relay (A/T), Back-Up Lamp Switch (M/T)
XM CAN (ENG) 7.qxp
4/14/2010
11:00 AM
Page 52
7 53
Maintenance
Description
Fuse rating
Protected component
EMS
BOX
ECU
30A
Engine Control Relay
ECU 3
20A
G4KE - Ignition Coil #1/2/3/4, Condenser
G6DC - Ignition Coil #1/2/3/4/5/6, Condenser #1/2
SENSOR 1
10A
G4KE - Variable Intake Manifold Valve, Crankshaft Position Sensor, Immobilizer Module, Camshaft
Position Sensor #1/2, Oil Control Valve #1/2, Canister Purge Control Solenoid Valve,
Canister Close Valve, Cooling Fan (Low) Relay
G6DC - Variable Intake Manifold Valve #1/2, Immobilizer Module, Canister Purge Control Solenoid
Valve, Oil Control Valve #1/2 (Exhaust), Oil Control Valve #1/2 (Intake), Canister Close
Valve
SENSOR 2
10A
G6DC - Cooling Fan (Low) Relay, Stop Lamp Switch
SENSOR 3
10A
G4KE - Injector #1/2/3/4, A/C Relay
G6DC - PCM, Injector #1/2/3/4/5/6, A/C Relay
SENSOR 4
15A
G4KE - Oxygen Sensor Up/Down, Fuel Pump Relay
G6DC - PCM, Oxygen Sensor #1/2/3/4, Fuel Pump Relay, Variable Charge Motion Actuator
ECU 1
15A
PCM
A/CON
10A
A/C Relay
F/PUMP
15A
Fuel Pump Relay
XM CAN (ENG) 7.qxp
4/14/2010
11:00 AM
Page 53