Kia Sorento - 2015 Fuse Box Diagram

Kia Sorento - 2015 Fuse Box Diagram

Safety features of your vehicle
54
3
Occupant Detection System
(ODS)
Your vehicle is equipped with an
occupant detection system in the
front passenger's seat.
The occupant detection system is
designed to detect the presence of a
properly-seated front passenger and
determine if the passenger's front air
bag should be enabled (may inflate)
or not. Only the front passenger front
air bag is controlled by the Occupant
Classification System.
WARNING
• If an air bag deploys, there
may be a loud noise followed
by a fine dust released in the
vehicle.
These conditions are
normal and are not hazardous
- the air bags are packed in this
fine powder.
The dust generat-
ed during air bag deployment
may cause skin or eye irrita-
tion as well as aggravate asth-
ma for some persons. Always
wash all exposed skin areas
thoroughly
with
lukewarm
water and a mild soap after an
accident in which the air bags
were deployed.
(Continued)
(Continued)
• The SRS can function only
when the ignition switch is in
the ON position. If the SRS air
bag warning light does not
illuminate,
or continuously
remains on after illuminating
for about 6 seconds when the
ignition switch is turned to the
ON position,
or after the
engine is started, comes on
while driving, the SRS is not
working
properly.
If
this
occurs,
have your vehicle
immediately inspected by an
authorized Kia dealer.
• Before you replace a fuse or
disconnect a battery terminal,
turn the ignition switch to the
LOCK position and remove the
ignition switch. Never remove
or replace the air bag related
fuse(s)
when
the
ignition
switch is in the ON position.
Failure to observe this warning
will cause the SRS air bag
warning light to illuminate.
OXMA033102
WARNING
Do not put anything in front of the
passenger air bag
indicator.
4 31
Features of your vehicle
How to reset the power tailgate
If the battery has been discharged or
disconnected, or if the related fuse has
been replaced or disconnected, for the
power tailgate to operate normally,
reset the power tailgate as follows:
1. Put the shift lever in P (Park).
2. Press the tailgate handle switch
and tailgate close button at the
same time for more than 3 sec-
onds. (the chime will sound).
3. Close the tailgate manually.
4. Open the tailgate using the tail-
gate handle switch and allow it to
fully open.
5. After fully opening, the tailgate will
complete initialization and lights
will flash twice indicating reset
complete.
If the power tailgate does not work
properly after the above procedure,
have the system checked by an
authorized Kia dealer.
NOTICE
If the power tailgate does not oper-
ate normally, first check the follow-
ing condition before using the power
tailgate.
• Make sure the shift lever is in
Park
Make sure the Power Tailgate Off
switch is not pressed.
If any of the power tailgate buttons
are pressed while the power tailgate
is in operation, the power tailgate
will stop. If any button is pressed
again the power tailgate will reverse
direction.
Power tailgate opening height
user setting
The driver may set the height of a
fully opened tailgate by following the
below instruction.
1. Position the tailgate manually to
the height you prefer.
2. Press the tailgate close button for
more than 3 seconds.
3.You will hear the system beep twice
indicating height has been set up.
The tailgate will open to the height
the driver has set up.
OXMA043325
4 37
Features of your vehicle
CAUTION
• To prevent possible damage
to the power window system,
do not open or close two win-
dows or more at the same
time. This will also ensure the
longevity of the fuse.
• Never try to operate the main
switch on the driver's door
and the individual door win-
dow switch in the opposite
directions at the same time. If
this is done, the window will
stop and cannot be opened or
closed.
WARNING -
Windows
• NEVER leave the ignition key
in the vehicle.
• NEVER leave any child unat-
tended in the vehicle. Even
very young children may inad-
vertently cause the vehicle to
move, entangle themselves in
the windows, or otherwise
injure themselves or others.
Always double check to make
sure all arms, hands, head
and other obstructions are
safely out of the way before
closing a window.
• Do not allow children to play
with the power windows. Keep
the driver’s door power win-
dow lock button in the LOCK
position (pressed). Serious
injury can result from uninten-
tional window operation by
the child.
• Do not extend heads or any
limbs outside the window
while the vehicle is in motion.
Features of your vehicle
76
4
Service Mode
Service Interval
Service in
It calculates and displays when you
need a scheduled maintenance
service (mileage or days).
If the remaining mileage or time
reaches 1,500 km. (900 mi) or 30
days, "Service in" message is dis-
played for several seconds each time
you set the ignition switch or Engine
Start/Stop Button to the ON position.
Service required
If you do not have your vehicle serv-
iced according to the already inputted
service interval, “Service required”
message is displayed for several sec-
onds each time you set the ignition
switch or Engine Start/Stop Button to
the ON position (The mileage and
time changes to "---").
To reset the service interval to the
mileage and days you inputted before:
- Press the RESET button
for
more than 1 second.
Service in OFF
If the service interval is not set,
“Service in OFF” message is dis-
played on the LCD display.
NOTICE
If any of the following conditions
occurs, the mileage and days may be
incorrect.
-
The battery cable is disconnected.
-
The fuse switch is turned off.
-
The battery is discharged.
OXM043119E
OXM043129E
OXM043130E
4 83
Features of your vehicle
Press start button again
(for smart key system)
• This warning message illuminates
if you can not operate the Engine
Start/Stop Button when there is a
problem with the Engine Start/Stop
Button system.
• It means that you could start the
engine by pressing the Engine
Start/ Stop Button once more.
• If the warning illuminates each
time
you
press
the
Engine
Start/Stop Button, have your vehi-
cle inspected by an authorized Kia
dealer.
Press start button with smart key
(for smart key system)
• This warning message illuminates
if you press the Engine Start/Stop
Button while the warning message
“Key not detected” is illuminating.
At this time, the immobilizer indica-
tor light blinks.
Check fuse "BRAKE SWITCH"
(for smart key system and auto-
matic transaxle)
• This warning message illuminates
if the brake switch fuse is discon-
nected.
• It means that you should replace
the fuse with a new one. If that is
not possible, you can start the
engine by pressing the Engine
Start/Stop Button for 10 seconds in
the ACC position.
OXMA043102
OXMA043110
OXMA043116
Features of your vehicle
86
4
Turn on "FUSE SWITCH"
(if equipped)
• This warning message illuminates
if the fuse switch on the fuse box is
OFF.
• It means that you should turn the
fuse switch on.
For more details, refer to “Fuses” in
chapter 7.
OXM043099E
Driving your vehicle
12
5
NOTICE
If the battery is weak or the smart
key does not work correctly, you
can start the engine by pressing
the engine start/stop button with
the smart key.
The side with the lock button
should
contact
the
engine
start/stop button directly.
When
you
press
the
engine
start/stop button directly with the
smart key, the smart key should
contact the button at a right angle.
(Continued)
(Continued)
When the stop lamp fuse is blown,
you can't start the engine normal-
ly. Replace the fuse with a new
one. If it is not possible, you can
start the engine by pressing the
ENGINE START/STOP
button
for 10 seconds
while it is in the
ACC position. The engine can
start without depressing the brake
pedal. But for your safety always
depress the brake pedal before
starting the engine.
CAUTION
Do not press the ENGINE
START/ STOP button for more
than 10 seconds except when
the stop lamp fuse is blown.
OXM053002
7 3
Maintenance
ENGINE COMPARTMENT
OXMA072001
* The actual engine room in the vehicle may differ from the illustration.
1. Engine coolant reservoir
2. Engine oil filler cap
3. Brake fluid reservoir
4. Air cleaner
5. Fuse box
6. Positive battery terminal
7. Negative battery terminal
8. Windshield washer fluid reservoir
9. Radiator cap
10. Engine oil dipstick
* : if equipped
2.4L GDI
Maintenance
4
7
OXMA073001
1. Engine coolant reservoir
2. Engine oil filler cap
3. Brake fluid reservoir
4. Air cleaner
5. Fuse box
6. Negative battery terminal
7. Positive battery terminal
8. Radiator cap
9. Engine oil dipstick
10. Windshield washer fluid reservoir
* if equipped
3.3L GDI
* The actual engine compartment in the vehicle may differ from the illustration.
Maintenance
64
7
FUSES
A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses.
This vehicle has 2 (or 3) fuse panels,
one located in the driver’s side panel
bolster, the other in the engine com-
partment near the battery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside the
fuse will
melt.
If the electrical system does not
work, first check the driver’s side
fuse panel.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and imme-
diately consult an authorized Kia
dealer.
Three kinds of fuses are used: blade
type for lower amperage rating, car-
tridge type, and multi fuse for higher
amperage ratings.
NOTICE
The actual fuse/relay panel label
may differ from equipped items.
WARNING
-
Fuse
replacement
Never replace a fuse with any-
thing but another fuse of the
same rating.
• A higher capacity fuse could
cause damage and possibly a
fire.
• Never install a wire or alu-
minum foil instead of the
proper fuse - even as a tem-
porary repair. It may cause
extensive wiring damage and
a possible fire.
CAUTION
Do not use a screwdriver or any
other metal object to remove
fuses because it may cause a
short circuit and damage the
system.
OLM079051N
Normal
Normal
Blade type
Cartridge type
Multi fuse
Blown
Blown
Normal
Blown
Normal
Blown
7 65
Maintenance
Inner panel fuse replacement
1. Turn the ignition switch and all
other switches off.
2. Open the fuse panel cover.
3. Pull the suspected fuse straight
out. Use the removal tool provided
on the
engine compartment fuse
panel cover.
4. Check the removed fuse; replace it
if it is blown.
Spare fuses are provided in the
engine compartment fuse panel.
5. Push in a new fuse of the same
rating, and make sure it fits tightly
in the clips.
If it fits loosely, consult an authorized
Kia dealer.
If you do not have a spare, use a
fuse of the same rating from a circuit
you may not need for operating the
vehicle, such as the power outlet
fuse.
If the headlights or other electrical
components do not work and the
fuses are OK, check the fuse panel
in the engine compartment. If a fuse
is blown, it must be replaced.
OXM073020
ODM072018
Maintenance
66
7
Fuse switch
Always, put the fuse switch at the ON
position.
If you move the switch to the OFF
position, some items such as audio
and digital clock must be reset and
transmitter (or smart key) may not
work properly.
Engine compartment fuse
replacement
1. Turn the ignition switch and all
other switches off.
2. Remove the fuse panel cover by
pressing the tab and pulling the
cover up.
3. Check the removed fuse; replace it
if it is blown. To remove or insert
the fuse, use the fuse puller in the
engine compartment fuse panel.
4. Push in a new fuse of the same
rating, and make sure it fits tightly
in the clips. If it fits loosely, consult
an authorized Kia dealer.
OXM073022
CAUTION
Always place the fuse switch in
the ON position while driving
the vehicle.
CAUTION
After checking the fuse panel in
the
engine
compartment,
securely install the fuse panel
cover. If not, electrical failures
may occur from water contact.
OXMA073023
7 67
Maintenance
Multi fuse
If the multi fuse is blown, it must be
removed as follows:
1. Turn off the engine.
2. Disconnect the negative battery
cable.
3. Remove the nuts shown in the pic-
ture above.
4. Replace the fuse with a new one
of the same rating.
5. Reinstall in the reverse order of
removal.
NOTICE
If the multi fuse is blown, consult an
authorized Kia dealer.
ODM072047
Maintenance
68
7
Fuse/relay panel description
Inside the fuse/relay panel covers,
you can find the fuse/relay label
describing fuse/relay name and
capacity.
NOTICE
Not all fuse panel descriptions in
this manual may be applicable to
your vehicle. It is accurate at the
time of printing. When you inspect
the fuse panel in your vehicle, refer
to the fuse panel label.
ODM072017
OXMA073116
7 69
Maintenance
Inner fuse panel
Description
Fuse rating
Protected component
MODULE 2
10A
Instrument Cluster (IND./MICOM), Steering Angle Sensor, Alternator, Smart Key Control Module, A/V &
Navigation Head Unit, STOP_SW, SI_ECU, HLLD LH/RH
MODULE 1
7.5A
SPORTS MODE SW/KEY_SOL, SPORT_MODE_SW
A/BAG IND
10A
Instrument Cluster (IND.), Digital Clock
A/BAG
15A
SRS Control Module, PODS Module
START
7.5A
E/R Fuse & Relay Box (Relay - Start, Sub Start, Burglar Alarm), PDM
WIPER RR
15A
ICM Relay Box (Rear Wiper Relay), Rear Wiper Motor, Multifunction Switch (Wiper)
WIPER FRT
25A
E/R Fuse & Relay Box (Wiper (Low) Relay), Front Wiper Motor, Multifunction Switch (Wiper)
MODULE 3
10A
ESC Off Switch, Front A/C Control Module, Instrument Cluster, Audio, MTS, A/V & Navigation Head Unit,
Tire Pressure Monitoring Module, Power Window Main Switch,
4WD ECU, P_WDW_PASS_SW_IMS,
Rear Parking Assist SNSR, FRT_DRV_SEAT_EXT, FRT_PASS_SEAT_EXT, CONSOLE_EXTN , IPM
(BCM IG1)
A/CON
7.5A
Front A/C Control Module, Active Incar Sensor, Cluster Ionize, ICM Relay Box (Rear A/C Relay) E/R
Fuse & Relay Box (Blower Relay)
AMP
30A
AMP
P/OUTLET 1
15A
-
P/OUTLET 2
20A
LUGGAGE_POWER_OUTLET, FRT_POWER_OUTLET_DRV
BLOWER RR
20A
ICM Relay Box (Rear A/C Relay)
Maintenance
70
7
Description
Fuse rating
Protected component
P/WDW LH
25A
Driver Power Window Relay, Power Window Main Switch, Rear Power Window Switch LH, Driver Safety
Power Window Module
P/WDW RH
25A
Passenger Power Window Relay, Power Window Main Switch
Passenger Power Window Switch, Rear Power Window Switch RH
DR LOCK
20A
Door Lock/Unlock Relay, ICM Relay Box (Two Turn Unlock Relay), Driver/Passenger Door Lock Actuator,
Rear Door Lock Actuator LH/RH, ICM Relay Box (T/GATE LATCH Relay)
SMART KEY 4
10A
PDM, Start Stop Button Switch, FOB Holder
S/HTR FRT
20A
FRT_DRV_SEAT_EXT, FRT_PASS_SEAT_EXT
P/SEAT DRV
30A
Driver Power Seat Switch, Driver Lumbar Support Switch
P/SEAT PASS
20A
Passenger Power Seat Switch
HTD STRG
15A
Steering wheel heater
F/LID
15A
Fuel Filler Door Switch
MODULE4
10A
O/S Mirror Switch, Power Window Switch, E/R Fuse & Relay Box(POWER OUTLET RLY), Digital Clock,
MTS, Audio, A/V & Navigation Head Unit
HTD MIRR
10A
Driver/Passenger Power Outside Mirror, Front A/C Control Module
SMART_KEY_1
25A
SMART KEY/SMK_UNIT
SMART_KEY_2
7.5A
Smart Key Control Module
SMART_KEY_3
7.5A
Smart Key Control Module
S/HEATER RR
15A
ICM Relay Box (RR SEAT WARMER LH RLY), ICM Relay Box (RR SEAT WARMER RH RLY)
INTERIOR LAMP
10A
DR_SCUFF_LP_DRV, DR_SCUFF_LP_PASS, DR_WARNG_SW, S_VISOR_LP_LH/RH, OHC_LAMP,
ROOM_LP, RL/RR_PERSONAL_LAMP, CARGO_LAMP
MULTIMEDIA
15A
Audio, A/V & Navigation Head Unit, MTS
MEMORY
10A
OBD_II, Front A/C Control Module, TPMS, Digital Clock, INSIDE_MIRR, S_WARMER_SW_LH/RH,
AIR_VENT_SEAT_SW_LH/RH, CLUSTER, O_S_MIRR_SW, P_WDW_MAIN_SW,
FRT_DRV_SEAT_EXT, P_WDW_PASS_SW
7 71
Maintenance
Engine compartment fuse panel
OXMA073027
OXMA073131
Maintenance
72
7
Engine compartment fuse panel
Description
Fuse rating
Protected component
MULTI
FUSE
I/P B+2
60A
IPM (Fuse - S/HTR FRT, P/Seat SUN ROOF-1 25A, IPS1 (FOG LH/RH, TAIL LAMP LH), ARISU LH
(HEAD LAMP LOW LH, HEAD LAMP HI LH, TURN SIG RL, TURN SIG FL)
BLOWER
40A
Blower Relay
RR HTD
40A
Rear Defogger Relay
ABS 1
40A
ESC Control Module, Multipurpose Check Connector
ABS 2
40A
ESC Control Module, Multipurpose Check Connector
I/P B+3
60A
SMART_KEY-1 25A, SMART_KEY-4 10A, MODULE-1 7.5A, SUNROOF-2 25A, (FUSE SW RLY,
INTERIOR LAMP 10A : DR_SCUFF_LP_DRV, DR_SCUFF_LP_PASS, DR_WARNG_SW,
S_VISOR_LP_LH/RH, OHC_LAMP, ROOM_LP, RL/RR_PERSONAL_LAMP, CARGO_LAMP, MULTI-
MEDIA 15A : Audio, A/V & Navigation Head Unit, MTS, MEMORY 10A : OBD_II, Front A/C Control
Module, TPMS, Digital Clock, INSIDE_MIRR, S_WARMER_SW_LH/RH, AIR_VENT_SEAT_SW_LH/
RH, CLUSTER, O_S_MIRR_SW, P_WDW_MAIN_SW, FRT_DRV_SEAT_EXT, P_WDW_PASS_SW)
I/P B+1
50A
AMP 30A, P/WDW LH 25A, P/WDW RH 25A, S/HEATER_RR 15A
MDPS
80A
MDPS_ECU
C/FAN
60A
E/R Fuse & Relay Box (C/FAN RLY)
FUSE
IGN 2
40A
Start Relay, W/O Smart Key - Ignition Switch, With Smart Key - E/R Fuse & Relay Box (IGN2 Relay)
TRAILER
30A
Trailer Power Outlet
IGN 1
40A
W/O Smart Key - Ignition Switch, With Smart Key - E/R Fuse & Relay Box (IGN1 Relay, ACC Relay )
HORN
15A
Horn Relay
DEICER
15A
Front Wiper Deicer Relay
I/P B+4
50A
IPM (DR LOCK 20A, BLOWER RR 20A, FUEL LID 15A, IPS3 (TAIL LAMP RH, TAIL INT LAMP),
ARISU RH (HEAD LAMP LOW RH, HEAD LAMP HI RH, TURN SIG RR, TURN SIG FR)
ABS
7.5A
ESC Control Module, Multipurpose Check Connector
B/UP LP
7.5A
Back-Up Lamp Relay (A/T), Back-Up Lamp Switch (M/T)
4WD
20A
4WD_ECU
7 73
Maintenance
Description
Fuse rating
Protected component
FUSE
B/A HORN
15A
B/A RLY
SENSOR 5
7.5A
PCM
TCU
15A
Transaxle Range Switch, PCM
EMS
BOX
A/CON
10A
E/R Fuse & Relay Box(BLOWER RLY, Front A/C Control Module)
AC INVERTER
30A
AC_INVERTER_UNIT
POWER OUTLET
25A
E/R Fuse & Relay Box (POWER OUTLET RLY), RR_P_OUTLET, FRT_POWER_OUTLET_PASS
P/TAILGATE
30A
PTGM
H/LAMP RH
10A
E/R Fuse & Relay Box(H/LAMP RH RLY), H_LP_RH
AMS
10A
E/R Fuse & Relay WIPER LO RLY), PCM
EMS
40A
EMS BOX(MAIN RLY(IGN_COIL 20A, ECU_1 20A, SNSR_1 10A, SNSR_2 10A, ECU_2 10A,
INJECTOR_1 10A), F/PUMP 15A, ECU_4 15A
SENSOR 1
10A
Theta : Purge Control Solenoid Valve, Oil Control Valve #1/2, Variable Intake Manifold Valve,
Crankshaft Position Sensor, Oxygen Sensor Up/Down
Lambda : PCM, Oxygen Sensor #1/2/3/4
SENSOR 2
10A
Theta : C/FAN RLY, Canister Close Valve
Lambda : C/FAN RLY, PCM, Canister Close Valve, Oil Control Valve #1/2 (Exhaust), Oil Control Valve
#1/2 (Intake), Purge Control Solenoid Valve, Variable Intake Manifold Valve #1/2,
Immobilizer Module
ECU 1
20A
PCM
F/PUMP
15A
Fuel Pump Relay
IGN_COIL
20A
Theta : IG_COIL_CAPACITOR, IG_COIL_1/2/3/4,
Lambda : CONDENSOR1/2,IGN_COIL_HARN_LAG, GN_COIL_2/4/6
INJECTOR_1
10A
Theta : Immobilizer Module, F/PUMP RLY,
Lambda : PCM, F/PUMP RLY
ECU 4
15A
Theta : PCM, Lambda : PCM, IDB