Ford Endeavour - 2016 Fuse Box Diagram

Ford Endeavour - 2016 Fuse Box Diagram

12 Volt DC Power Point
WARNING
Incorrect use of the 12 Volt DC Power
Point can cause damage not covered
by your warranty, and can result in
fire or serious injury.
Note:
If used when the vehicle is not
running, the battery will run out of charge.
There may be insufficient power to restart
your vehicle.
Note:
When you switch the ignition on, you
can use the socket to power 12 volt
appliances with a maximum current rating
of 15 amps.
After you switch the ignition off, the power
supply works only for a maximum of 75
minutes.
Note:
Do not insert objects other than an
accessory plug into the power point. This
damages the outlet and blows the fuse.
Note:
Do not hang any type of accessory or
accessory bracket from the plug.
Note:
Do not use the power point over the
vehicle capacity of 12 volt DC 150 watt or a
fuse may blow.
Note:
Incorrect use of the power point can
cause damage not covered by your
warranty.
Note:
Always keep the power point caps
closed when not in use.
Run the engine for full capacity use of the
power point.
To prevent the battery from running out of
charge:
Do not use the power point longer than
necessary when your engine is not
running.
Do not leave devices plugged in
overnight or when your vehicle is in park
(P) for extended periods.
Locations
Power points may be in the following
locations:
On the instrument panel above the cup
holders.
On the rear of the center console.
In the rear cargo area.
AC Power Point
WARNING
Do not keep electrical devices
plugged in the power point whenever
the device is not in use. Do not use
any extension cord with the 230 volt or 110
volt AC power point, since it will defeat the
safety protection design. Doing so may
cause the power point to overload.
Powering multiple devices can reach
beyond the 150 watt load limit and could
result in fire or serious injury.
Note:
Keep the vehicle running to use the
power point.
Note:
Depending on your vehicle, the power
point may open to the right or upward.
Note:
Depending on your vehicle, the power
point may provide 230 volt AC power, or 110
volt AC power.
With the engine off, the power point works
up to maximum 75 minutes (or less). The
power point turns off automatically if the
battery voltage becomes low. This
prevents the vehicle battery from running
out of charge.
109
Endeavour (TEC), EB3B-19G219-ZCA enIND
Auxiliary Power Points
P
R
N
D
S
-
+
E136209
To exit SelectShift mode, return the
selector lever to drive (D).
When your vehicle is stationary, only the
1st and 2nd gears can be selected. Manual
shifting is sequential, therefore gears
cannot be skipped.
Emergency Park Position Release
Lever
WARNINGS
Do not drive your vehicle until you
verify that the brake lamps are
working.
When doing this procedure, you need
to take the transmission out of park
(P) which means your vehicle can
roll freely. To avoid unwanted vehicle
movement, always fully apply the parking
brake prior to doing this procedure. Use
wheels chocks if appropriate.
If the parking brake is fully released,
but the brake warning lamp remains
illuminated, the brakes may not be
working properly. Have your vehicle
checked as soon as possible.
Note:
For some markets this feature is
disabled.
Your vehicle has a brake-shift interlock
feature that prevents moving the gearshift
lever from park (P) when the ignition is on
and you do not press the brake pedal.
The system requires service if you cannot
move the gearshift lever out of park (P)
with the ignition on and the brake pedal
pressed. It is possible that a fuse has blown
or your vehicle
s brake lamps are not
operating properly. See
Fuse
Specification Chart
(page ?).
If the fuse is not blown and the brake
lamps are working properly, the following
procedure allows you to move the selector
lever from park (P):
Note:
Apply the parking brake and switch
the ignition off before performing this
procedure.
E132721
1.
Lift up the cover in the center console
next to the transmission selector lever
with a suitable tool.
2.
Push down the locking button in the
slot and simultaneously move the
selector lever out of park (P) and into
another gear.
122
Endeavour (TEC), EB3B-19G219-ZCA enIND
Transmission
HAZARD WARNING FLASHERS
E71943
The hazard warning button is
located on the instrument panel.
Use it when your vehicle is creating a safety
hazard for other motorists.
Press the button to turn on the hazard
warning function, and the front and rear
direction indicators will flash.
Press the button again to turn them off.
Note:
If used when the engine is not
running, the battery will lose charge. There
may be insufficient power to restart your
engine.
Note:
Depending on applicable laws and
regulations in the country for which your
vehicle was originally built, the hazard
warning flashers may flash if you brake
heavily.
FIRST AID KIT
First aid kit is stored in the glove box. It
contains spare fuses, spare bulbs and
emergency medical treatment kit. Use it
under emergency situations.
FIRE EXTINGUISHER
The fire extinguisher is in front of the
driver's seat. Every month you should
visually inspect it and verify that the
indicator and the body show no damage,
the trigger is in good operating condition,
and there is no obstruction to removing the
extinguisher.
The operating directions are on the fire
extinguisher's body. The maintenance is
the responsibility of the owner; therefore
the owner should carry out the
maintenance according to the
manufacturer instructions imprinted on
the equipment.
You should respect the expiration date
annotated on the extinguisher, observing
the recommendations for checking it.
Before you use the fire extinguisher, make
sure you remove the transparent plastic
packaging used for the transportation of
the fire extinguisher to prevent obstruction.
When replacing the extinguisher, make
sure the new fire extinguisher is of type dry
powder ABC.
WARNING TRIANGLE
Space is provided in the luggage
compartment.
JUMP STARTING THE VEHICLE
WARNINGS
Do not use fuel lines, engine rocker
covers or the intake manifold as
grounding points.
Connect batteries with only the same
nominal voltage.
Use only adequately sized cables
with insulated clamps.
Note:
Do not disconnect the battery of the
disabled vehicle as this could damage the
vehicle electrical system.
157
Endeavour (TEC), EB3B-19G219-ZCA enIND
Roadside Emergencies
FUSE BOX LOCATIONS
Fuse Box Locations
E
D
C
B
A
E206155
Pre-fuse box.
A
Engine compartment fuse box
(Power Distribution Box - PDB).
B
High current fuse box (below the
PDB).
C
Passenger compartment fuse
box.
1
D
Passenger compartment fuse
box.
2
E
1
- Left Hand Drive.
2
- Right Hand Drive.
Pre-Fuse Box
E206156
Your vehicle has a pre-fuse box located in
the engine compartment attached to the
positive battery post. This box contains
several high current fuses. If replacement
of these high current fuses is required, see
an authorized dealer.
Engine Compartment Fuse Box
(Power Distribution Box - PDB)
E206157
WARNINGS
Always disconnect the battery before
servicing high current fuses.
To reduce risk of electrical shock,
always replace the cover to the
engine compartment fuse box before
reconnecting the battery or refilling fluid
reservoirs.
161
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
The engine compartment fuse box has
high-current fuses that protect your
vehicle's main electrical systems from
overloads.
When you disconnect and reconnect the
battery, you will need to reset some
features. See
Changing the 12V Battery
(page 194).
Lift the release lever at the rear of the cover
to remove it.
High Current Fuse Box
E206158
Your vehicle has a pre-fuse box located in
the engine compartment below the engine
compartment fuse box. This box contains
several high current fuses. If replacement
of these high current fuses is required, see
an authorized dealer.
Passenger Compartment Fuse Box
E206167
The fuse box is located behind the access
cover on the outboard side of the steering
column.
FUSE SPECIFICATION CHART
- 2.2L DIESEL
Engine Compartment Fuse Box
WARNINGS
Always disconnect the battery before
servicing high-current fuses.
To reduce risk of electrical shock,
always replace the cover to the
engine compartment fuse box before
reconnecting the battery or refilling fluid
reservoirs.
162
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
The engine compartment fuse box has
high-current fuses that protect your
vehicle's main electrical systems from
overloads. When you disconnect and
reconnect the battery, you will need to
reset some features. See
Changing the
12V Battery
(page 194). Lift the release
levers at the rear of the cover to remove it.
E190797
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
Not used.
25
3
1
Starter motor solenoid relay.
-
2
Rear wiper, rain sensor.
15
1
3
Front blower motor relay.
-
4
Power point 3 (console rear).
20
3
5
Headlamp low beam relay (high intensity discharge)
(If fitted).
-
6
163
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
Powertrain control module.
20
1
7
Power train control module - volumetric control valve,
EGR cooler bypass, TMAF.
20
1
8
Powertrain control module relay.
-
9
Power point 1 / cigar lighter.
20
3
10
Not used.
15
2
11
Powertrain control module - fan drive, glow plug control
module.
15
2
12
Not used.
15
2
13
Powertrain control module - PCV Heater.
15
2
14
Run/start relay.
-
15
Power point 2 / cigar lighter .
20
3
16
Power point 4 - 3rd row power point .
20
3
17
Not used.
10
1
18
Electric power assisted steering.
10
1
19
Headlamp switch, headlamp levelling motor.
10
1
20
Transfer case control module - terrain management
switch.
15
1
21
Air conditioning compressor.
10
1
22
Parking aid rear view camera, blind spot monitoring
module, adaptive speed control radar and head up
display (if fitted).
15
1
23
Not used.
-
24
Anti-lock brake system.
10
2
25
Mirror adjust switch.
10
2
26
164
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
PTC Heater (if fitted).
5
1
27
Powertrain control module.
10
1
28
Rear window washer pump.
10
1
29
Not used.
-
30
Not used.
-
31
Not used.
-
32
Air conditioning clutch relay.
-
33
Not used.
-
34
Transmission control module.
15
1
35
Not used.
-
36
Heated exterior mirror.
10
1
37
Not used.
-
38
Not used.
-
39
Fuel pump relay.
-
40
Horn relay.
-
41
Seat third row power fold relay.
-
42
Not used.
15
1
43
Headlamp washer pump.
25
1
44
Not used.
-
45
Not used.
10
2
46
Brake pedal switch.
10
2
47
Horn.
20
1
48
Not used.
-
49
Not used.
-
50
165
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
Not used.
-
51
Not used.
-
52
Not used.
-
53
Not used.
-
54
Not used.
-
55
Rear blower motor relay.
-
86
1
Micro fuse.
2
Dual micro fuse.
3
M-type fuse.
Power Distribution Box - Bottom
There are fuses located on the bottom of
the fuse box. To access the bottom of the
fuse box, do the following:
A
1
2
E206171
1
Towards the front side of the
vehicle.
A
1.
Release the two latches, located on
both sides of the fuse box.
2.
Raise the rear side of the fuse box from
the cradle.
3
5
5
E206174
3.
Move the fuse box toward the rear side
of the engine compartment and rotate
as shown in the graphics.
166
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
4.
Pivot the rear side of the fuse box to
access the bottom side.
5.
Release the two latches to open the
fuse cover.
E190798
Protected Components
Fuse Amp Rating
Fuse/Relay Number
Fuel pump control module.
30
3
56
Not used.
-
57
Not used.
-
58
Not used.
-
59
Not used.
-
60
Not used.
-
61
Body control module 1
(lighting).
50
4
62
Not used.
-
63
167
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse/Relay Number
Trailer auxiliary.
20
3
64
Heated front seats.
20
3
65
Not used.
-
66
Body control module 2
(lighting).
50
4
67
Rear window defroster.
40
3
68
Antilock brake system
valves.
30
3
69
Passenger power seat.
20
3
70
Not used.
-
71
Third row power fold seat.
30
3
72
Not used.
-
73
Driver power seat.
20
3
74
Rear blower motor.
25
3
75
Left-hand low beam high-
intensity discharge head-
lamps (If fitted).
20
3
76
AWD drive module.
25
3
77
AWD drive module.
25
3
78
Blower motor.
40
4
79
Right-hand low beam high-
intensity discharge head-
lamps (If fitted)
20
3
80
Inverter.
40
3
81
Anti-lock brake system
pump.
60
4
82
Windshield wiper motor.
25
3
83
168
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse/Relay Number
Starter motor solenoid.
30
3
84
Power lift gate module.
30
3
85
Trailer module.
40
4
87
1
Micro fuse.
2
Dual micro fuse.
3
M-type fuse.
4
LPJ-type fuse.
Battery Mounted Fuse Link
E206156
Protected Components
Fuse Amp
Rating
Fuse
Alternator.
225
1
Electronic power assist steering.
125
2
169
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
High Current Fuse Box
E206158
Protected Components
Fuse Amp
Rating
Fuse
Glow plug module.
60
1
Body control module.
125
2
Body control module.
50
3
Busbar through to power distribution box.
-
4
PTC heater (if fitted).
100
5
Passenger Compartment Fuse Box
The fuse box is located below and
outboard of the steering column behind
the access cover.
170
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
E145984
Protected Components
Fuse Amp Rating
Fuse
Demand lamp / battery saver - overhead console,
automatic transmission gear shifter. glove box lamp,
sun visor, grab handle, Map lamps.
10
1
1
Not used (spare).
7.5
1
2
Driver door latch /fuel flap unlock relay. Door double/
aux lock relay.
20
1
3
Not used (spare).
5
1
4
Subwoofer amplifier.
20
1
5
Not used (spare).
10
2
6
Not used (spare).
10
2
7
Security horn.
10
2
8
Not used (spare).
10
2
9
Power liftgate module.
5
2
10
Interior motion sensor.
5
2
11
171
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse
Electronic control panel, climate control module,
rear auxiliary module.
7.5
2
12
Instrument cluster, steering column control module,
smart data link connector.
7.5
2
13
Not used (spare).
10
2
14
Gateway module/smart data link connector, OBD II
(RHD).
10
2
15
Child lock.
15
1
16
Battery backed sounder.
5
2
17
Ignition switch.
5
2
18
Not used (spare).
7.5
2
19
Headlamp control module.
7.5
2
20
Humidity and in car temperature sensor.
5
2
21
Not used (spare).
5
2
22
Inverter, door lock switch, moon roof.
10
1
23
Central locking system.
20
1
24
Driver door control module (power window - one
touch up/down all doors)
30
1
25
Driver door power window switch memory (with one
touch up/down driver only)
Passenger door control module (power window)
(one touch up/down)
30
1
26
Moonroof.
30
1
27
Not used (spare).
20
1
28
Left rear door control module (power window) (one
touch up/down).
30
1
29
Right rear door control module (power window) (one
touch up/down).
30
1
30
172
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse
Not used (spare).
15
1
31
Radio transceiver module, SYNC, global positioning
system module, multi function display, door entry
remote.
10
1
32
Audio unit.
20
1
33
Run/start relay.
30
1
34
Restraints control module.
5
1
35
Interior rear view mirror electrochromatic.
15
1
36
Not used (spare).
15
1
37
Power windows (without door control module) (one
touch up/down - driver only).
30
3
38
1
Micro fuse.
2
Dual micro fuse.
3
PTC fuse
FUSE SPECIFICATION CHART
- 3.2L DIESEL
Engine Compartment Fuse Box
WARNINGS
Always disconnect the battery before
servicing high-current fuses.
To reduce risk of electrical shock,
always replace the cover to the
engine compartment fuse box before
reconnecting the battery or refilling fluid
reservoirs.
The engine compartment fuse box has
high-current fuses that protect your
vehicle's main electrical systems from
overloads. When you disconnect and
reconnect the battery, you will need to
reset some features. See
Changing the
12V Battery
(page 194). Lift the release
levers at the rear of the cover to remove it.
173
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
E190797
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
Not used.
25
3
1
Starter motor solenoid relay.
-
2
Rear wiper, rain sensor.
15
1
3
Front blower motor relay.
-
4
Power point 3 (console rear).
20
3
5
Headlamp low beam relay (high intensity discharge).
-
6
Powertrain control module.
20
1
7
Power train control module - volumetric control valve,
EGR cooler bypass, TMAF.
20
1
8
174
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
Powertrain control module relay.
-
9
Power point 1 / cigar lighter.
20
3
10
Powertrain control module - NOX sensor (if fitted).
15
2
11
Powertrain control module - fan drive, glow plug control
module.
15
2
12
Not used.
15
2
13
Not used.
15
2
14
Run/start relay.
-
15
Power point 2 / cigar lighter .
20
3
16
Power point 4 - 3rd row power point .
20
3
17
Not used.
10
1
18
Electric power assisted steering.
10
1
19
Headlamp switch, headlamp levelling motor.
10
1
20
Transfer case control module - terrain management
switch.
15
1
21
Air conditioning compressor.
10
1
22
Parking aid rear view camera, blind spot monitoring
module, adaptive speed control radar and heads up
display (if fitted).
15
1
23
Exhaust emissions - rear dosing control module (if
fitted).
5
1
24
Anti-lock brake system.
10
2
25
Mirror adjust switch.
10
2
26
PTC Heater (if fitted).
5
1
27
Powertrain control module.
10
1
28
175
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
Rear window washer pump.
10
1
29
Not used.
-
30
Not used.
-
31
Not used.
-
32
Air conditioning clutch relay.
-
33
Not used.
-
34
Transmission control module.
15
1
35
Not used.
-
36
Heated exterior mirror.
10
1
37
Not used.
-
38
Not used.
-
39
Fuel pump relay.
-
40
Horn relay.
-
41
Seat third row power fold relay.
-
42
Exhaust emissions - rear dosing control module (if
fitted).
15
1
43
Headlamp washer pump.
25
1
44
Not used.
-
45
Not used.
10
2
46
Brake pedal switch.
10
2
47
Horn.
20
1
48
Not used.
5
1
49
Exhaust emissions - rear dosing control module (if
fitted).
15
1
50
Not used.
-
51
176
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp
Rating
Fuse/Relay
Number
Not used.
-
52
Not used.
-
53
Exhaust emissions - rear dosing control module (if
fitted).
10
2
54
Exhaust emissions - rear dosing control module (if
fitted).
10
2
55
Rear blower motor relay.
-
86
1
Micro fuse.
2
Dual micro fuse.
3
M-type fuse.
Power Distribution Box - Bottom
There are fuses located on the bottom of
the fuse box. To access the bottom of the
fuse box, do the following:
A
1
2
E206171
1
Towards the front side of the
vehicle.
A
1.
Release the two latches, located on
both sides of the fuse box.
2.
Raise the rear side of the fuse box from
the cradle.
3
5
5
E206174
3.
Move the fuse box toward the rear side
of the engine compartment and rotate
as shown in the graphics.
177
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
4.
Pivot the rear side of the fuse box to
access the bottom side.
5.
Release the two latches to open the
fuse cover.
E190798
Protected Components
Fuse Amp Rating
Fuse/Relay Number
Fuel pump control module.
30
3
56
Not used.
-
57
Not used.
-
58
Not used.
-
59
Not used.
-
60
Not used.
-
61
Body control module 1
(lighting).
50
4
62
Not used.
-
63
178
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse/Relay Number
Trailer auxilliary.
20
3
64
Heated front seats.
20
3
65
Not used.
-
66
Body control module 2
(lighting).
50
4
67
Rear window defroster.
40
3
68
Antilock brake system
valves.
30
3
69
Passenger power seat.
20
3
70
Not used.
-
71
Third row power fold seat.
30
3
72
Not used.
-
73
Driver power seat.
20
3
74
Rear blower motor.
25
3
75
Left-hand low beam high-
intensity discharge head-
lamps (if fitted).
20
3
76
AWD module.
25
3
77
AWD module.
25
3
78
Blower motor.
40
4
79
Right-hand low beam high-
intensity discharge head-
lamps (if fitted).
20
3
80
Inverter.
40
3
81
Anti-lock brake system
pump.
60
4
82
Windshield wiper motor.
25
3
83
179
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse/Relay Number
Starter motor solenoid.
30
3
84
Power lift gate module.
30
3
85
Trailer module.
40
4
87
1
Micro fuse.
2
Dual micro fuse.
3
M-type fuse.
4
LPJ-type fuse.
Battery Mounted Fuse Link
E206156
Protected Components
Fuse Amp
Rating
Fuse
Alternator.
225
1
Electronic power assist steering.
125
2
180
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
High Current Fuse Box
E206158
Protected Components
Fuse Amp
Rating
Fuse
Glow plug module.
60
1
Body control module.
125
2
Body control module.
50
3
Busbar through to power distribution box.
-
4
PTC Heater (if fitted).
100
5
Passenger Compartment Fuse Box
The fuse box is located below and
outboard of the steering column behind
the access cover.
181
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
E145984
Protected Components
Fuse Amp Rating
Fuse
Demand lamp / battery saver - overhead console,
automatic transmission gear shifter. glove box lamp,
sun visor, grab handle, Map lamps.
10
1
1
Not used (spare).
7.5
1
2
Driver door latch /fuel flap unlock relay. Door double/
aux lock relay.
20
1
3
Not used (spare).
5
1
4
Subwoofer amplifier.
20
1
5
Not used (spare).
10
2
6
Not used (spare).
10
2
7
Security horn.
10
2
8
Not used (spare).
10
2
9
Power liftgate module.
5
2
10
Interior motion sensor.
5
2
11
182
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse
Electronic control panel, climate control module,
rear auxiliary module.
7.5
2
12
Instrument cluster, steering column control module,
smart data link connector.
7.5
2
13
Not used (spare).
10
2
14
Gateway module/smart data link connector - OBD
II (RHD).
10
2
15
Child lock.
15
1
16
Battery backed sounder.
5
2
17
Ignition switch.
5
2
18
Not used (spare).
7.5
2
19
Headlamp control module (if fitted).
7.5
2
20
Humidity and in car temperature sensor.
5
2
21
Not used (spare).
5
2
22
Inverter, door lock switch, moon roof, driver door
window switch (one touch up/down all doors.
10
1
23
Central locking system.
20
1
24
Driver door control module (power window one
touch up/down all doors) Driver door power window
switch memory (with one touch up/down driver only)
30
1
25
Passenger door control module (power window -
one touch up/down).
30
1
26
Moonroof.
30
1
27
Not used (spare).
20
1
28
Left rear door control module (power window - one
touch up/down).
30
1
29
Right rear door control module (power window - one
touch up/down).
30
1
30
183
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Protected Components
Fuse Amp Rating
Fuse
Not used (spare).
15
1
31
Radio transceiver module, SYNC, global positioning
system module, multi function display, door entry
remote.
10
1
32
Audio unit.
20
1
33
Run/start relay.
30
1
34
Restraints control module.
5
1
35
Interior rear view mirror electrochromatic.
15
1
36
Not used (spare).
15
1
37
Power windows (without door control module - with
one touch up/down driver only).
30
3
38
1
Micro fuse.
2
Dual micro fuse.
3
PTC fuse
CHANGING A FUSE
WARNINGS
Do not modify the electrical system
of your vehicle in any way. Have
repairs to the electrical system and
the replacement of relays and high current
fuses carried out by an authorized dealer.
Switch the ignition and all electrical
equipment off before attempting to
change a fuse.
Always replace a fuse with one that
has the specified amperage rating.
Using a fuse with a higher amperage
rating can cause severe wire damage and
could start a fire.
E142430
If electrical components in your vehicle are
not working, a fuse may have blown. Check
the appropriate fuses before replacing any
electrical components.
184
Endeavour (TEC), EB3B-19G219-ZCA enIND
Fuses
Left Hand Drive
A
B
C
D
E
F
G
H
I
E200869
Engine coolant reservoir cap. See
Engine Coolant Check
(page 191).
A
Brake and clutch fluid reservoir cap. See
Brake and Clutch Fluid Check
(page
193).
B
Engine oil dipstick. See
Engine Oil Dipstick
(page 191).
C
Fuel filter water drain. See
Draining the Fuel Filter Water Trap
(page 194).
D
Engine compartment fuse box. See
Fuses
(page 161).
E
Battery. See
Maintenance
(page 185).
F
Engine oil filler cap. See
Engine Oil Check
(page 191).
G
Washer fluid reservoir cap. See
Washer Fluid Check
(page 193).
H
Air Cleaner.
I
188
Endeavour (TEC), EB3B-19G219-ZCA enIND
Maintenance
Right Hand Drive
A
B
C
D
I
E
F
G
H
E200848
Engine coolant reservoir cap. See
Engine Coolant Check
(page 191).
A
Brake and clutch fluid reservoir cap. See
Brake and Clutch Fluid Check
(page
193).
B
Engine oil dipstick. See
Engine Oil Dipstick
(page 191).
C
Fuel filter water drain. See
Draining the Fuel Filter Water Trap
(page 194).
D
Engine compartment fuse box. See
Fuses
(page 161).
E
Battery. See
Maintenance
(page 185).
F
Engine oil filler cap. See
Engine Oil Check
(page 191).
G
Washer fluid reservoir cap. See
Washer Fluid Check
(page 193).
H
Air Cleaner.
I
190
Endeavour (TEC), EB3B-19G219-ZCA enIND
Maintenance
AUDIO UNIT CLOCK AND DATE
DISPLAYS
Changing the Time
The clock can be set at any time when the
system is in the one hour mode or the
ignition switch is in the ACC or ON position.
Note:
Vehicles with AM/FM/DAB/CD: The
time can be adjusted using the hour and
minute buttons on the screen.
To advance the hours, press the
HOUR
SET
button. To advance the minutes, press
the
MINUTE SET
button while the time is
flashing.
Note:
Vehicles with Bluetooth/NAV: The
time can be adjusted using the clock button
on the audio control panel.
Note:
The time can be adjusted using the
cursor arrow buttons on the audio control
panel.
Vehicles with
AM/FM/DAB/USB/Bluetooth
1.
Press the
MENU
button.
2.
Use the up and down arrow button to
select the clock settings.
3.
Short press the
OK
button or right
arrow button to enter the clock
settings.
4.
Use the up and down arrow button to
select the set time.
5.
Use the up and down arrow button to
adjust hours.
6.
Use the right and left arrow button to
scroll to the minutes.
7.
Use the up and down arrow button to
adjust minutes.
8.
Use the OK button to save the settings.
Vehicles with AM/FM/DAB/CD/SYNC
1.
Press the
MENU
button.
2.
Use the up and down arrow button to
select the clock settings.
3.
Press
OK
button or right arrow button
to enter clock settings.
4.
Use the up and down arrow button to
select the set time.
5.
Use the up and down arrow button to
adjust hours.
6.
Use the right and left arrow button to
scroll to the minutes.
7.
Use the up and down arrow button to
adjust minutes.
8.
Use the
OK
button to save the settings.
Vehicles with AM/FM/DAB/CD/SYNC
2
See
Settings
(page 291).
Exact Hour Adjustment
You can set the time to the beginning of
an hour using this feature.
Press the
CLOCK
button for about two
seconds until a beep is heard. The
clock's current time will flash.
Press the
CLOCK
button again and the
time will be adjusted as follows:
Example
Current set time between 12:01 and
12:29 will change to 12:00 exactly.
Current set time between 12:30 and
12:59 will change to 1:00 exactly.
Note:
If the power supply to the unit is
interrupted (if the fuse blows or the vehicle's
battery is disconnected), the clock will need
to be reset.
236
Endeavour (TEC), EB3B-19G219-ZCA enIND
Audio System