Ford Ka - 2010 Fuse Box Diagram

Ford Ka - 2010 Fuse Box Diagram

114
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
ALPHABETICAL
INDEX
YOUR CAR
SAFETY
STARTING AND
DRIVING
IN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULB
GENERAL INSTRUCTIONS
Before changing a bulb check the
contacts for oxidation.
Burnt bulbs must be replaced by
others of the same type and power.
Always check the height of the
headlight beam after changing a bulb.
When a bulb is not working, check
that the corresponding fuse is intact
before replacing it: refer to the “If a
fuse blows” paragraph in this chapter
for fuse location.
Modifications or repairs to
the electrical system that
are not carried out properly or do
not take the system’s technical
specifications into account can
cause malfunctions leading to the
risk of fire.
WARNING
Halogen bulbs contain gas
under pressure, if they
break glass fragments may be
thrown around.
WARNING
When handling halogen
bulbs just touch the metal
part. Touching the
transparent part of the bulb
with your fingers may reduce the
intensity of the emitted light and
even compromise duration of the
lamp. In case of accidental contact,
rub the lamp with a cloth and spirit
and leave to dry.
101-130 Ford KA GB
15-07-2008
8:50
Pagina 114
122
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
ALPHABETICAL
INDEX
YOUR CAR
SAFETY
STARTING AND
DRIVING
IN AN
EMERGENCY
IF A FUSE BLOWS
GENERALITIES fig. 30
The fuse is a protective device for the
electric system: it comes into action (i.e.
it cuts off) mainly due to a fault or
improper action on the system.
Check the efficiency of the
corresponding fuse when a device does
not work: the conducting element
A
must not be interrupted. If it is, replace
the blown fuse with a new one having
the same amperage (same colour).
B
intact fuse.
C
fuse with damaged filament.
To replace a fuse use tweezers
D
,
hooked inside the fuse compartment
cover on the left side of the dashboard.
To identify the
protection fuse, see the
tables in the following pages.
open the bulb cover
B-fig. 29
and
replace the snap-fitted bulb
C
;
re-close the bulb cover
B
on the
lens;
Reinstall the ceiling light properly
inserting it into its seat on one side
first, and then pressing the other side
until it clicks into position.
fig. 29
KA00098m
fig. 30
KA00099m
Never replace a blown fuse
with metal wires or other
materials.
Never replace a fuse with
another having higher
amperage; FIRE HAZARD.
In case of general protection fuse
intervention (MEGA-FUSE, MIDI-
FUSE, MAXI-FUSE) contact Ford
Dealership.
Remove the key from the ignition
switch and switch off all loads
before replacing a fuse.
WARNING
Should the fuse blow
again, contact Ford
Dealership.
WARNING
101-130 Ford KA GB
15-07-2008
8:50
Pagina 122
123
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
ALPHABETICAL
INDEX
YOUR CAR
SAFETY
STARTING AND
DRIVING
IN AN
EMERGENCY
FUSE LOCATION
Dashboard fuses
Left-hand drive versions
To access the fuse you must remove
the press-fitted cover
E
.
The 5A fuse for door mirror demisting
is located in the diagnostic socket area,
as shown in
fig. 31
.
The control unit show in
fig. 32
is
present in the lower area, besides the
pedals.
Right-hand drive versions
To gain access to the fuse box shown in
fig. 32
, open flap
F
located inside the
glove compartment
fig. 33
.
fig. 31
E
KA00107m
fig. 32
KA00100m
fig. 33
F
KA00125m
101-130 Ford KA GB
15-07-2008
8:50
Pagina 123
124
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
ALPHABETICAL
INDEX
YOUR CAR
SAFETY
STARTING AND
DRIVING
IN AN
EMERGENCY
Engine compartment control unit
fig. 34 e 35
A second control unit is located on the
right side of the engine compartment,
next to the battery; to access it press
device
I
, release tabs
M
and remove
cover
L
.
The ID number of the electrical
component corresponding to each fuse
can be found on the back of the cover.
fig. 34
fig. 35
KA00101m
KA00102m
If you need to wash the
engine compartment, take
care not to directly hit the
engine compartment
control unit with the water jet.
101-130 Ford KA GB
15-07-2008
8:50
Pagina 124
144
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
ALPHABETICAL
INDEX
YOUR CAR
SAFETY
STARTING AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
CLEANING SEATS AND FABRIC
PARTS
Remove dust with a soft brush or a
vacuum cleaner.
Rub the seats with a sponge moistened
with a solution of water and neutral
detergent.
INTERIOR PLASTIC PARTS
It is advisable to clean interior plastic
parts with a moist cloth and a solution
of water and mild soap. Use specific
products for cleaning plastic, without
solvents and specifically designed to
prevent damage to the appearance and
colour of the treated parts to remove
grease and tough stains.
IMPORTANT Never use spirit or
petroleum to clean the instrument
panel.
EQUIPMENT
Periodically check that water is not
trapped under the mats (due to water
dripping off shoes, umbrellas, etc.)
which could cause oxidisation of the
sheet metal.
Windows
Use specific window cleaner products.
Use also clean cloths to avoid scratching
the glass or damaging the transparency.
IMPORTANT Wipe the rear window
inside gently with a cloth in the
direction of the filaments to avoid
damaging the heating device.
Engine compartment
At the end of each winter, thoroughly
wash the engine compartment taking
care not to direct the water jet against
the electronic control units and the
relay/fuse control unit on the left side of
the engine compartment (running
direction). Have this operation
performed at a specialised workshop.
IMPORTANT Perform this operation
on a cold engine and with the key at
STOP
. After the washing operation,
make sure that the various protections
(e.g. rubber caps and guards) have not
been removed or damaged.
Front headlights
IMPORTANT Never use aromatic
substances (e.g.: petrol) or ketenes
(e.g.: acetone) for cleaning front
headlight plastic lens.
Never use flammable
products, such as petrol
ether or rectified petrol to clean
inside the car. The electrostatic
charges which are generated by
rubbing during the cleaning
operation may cause a fire.
WARNING
Don’t keep aerosol cans in
the vehicle: risk of
explosion. Aerosol cans must not be
exposed to a temperature
exceeding 50°C. When the vehicle
is exposed to sunlight, inner
temperature can greatly exceed
this value.
WARNING
131-144 Ford KA GB
17-07-2008
9:16
Pagina 144
118
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
KNOWING
YOUR CAR
IN AN
EMERGENCY
CHANGING A BULB
GENERAL INSTRUCTIONS
Before changing a bulb check
the contacts for oxidation;
burnt bulbs must be replaced by
others of the same type and power;
always check the headlight beam
aiming after changing a bulb;
when a light is not working, check
that the corresponding fuse is intact
before changing the bulb. For the
location of fuses, refer to the
“Changing a fuse” paragraph in this
section.
Modifications or repairs
to the electric system that
are not carried out properly or
do not take the system technical
specifications into account can
cause malfunctions leading to
the risk of fire.
WARNING
Halogen bulbs contain
gas under pressure,
if they break glass fragments
may be thrown around.
WARNING
When handling halogen
bulbs just touch the metal
part. If the transparent bulb
is touched with the fingers,
its lighting intensity is reduced and
life of the bulb may be compromised.
If touched accidentally, rub the bulb
with a cloth moistened with
methylated spirit and allow to dry.
105-132 Ford KA EN
14-10-2010
11:37
Pagina 118
126
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
KNOWING
YOUR CAR
IN AN
EMERGENCY
REPLACING FUSES
GENERAL INFORMATION fig. 30
Fuses protect the electric system: they
cut in (i.e. they blow) in the event
of a failure or improper action on
the system.
When a device does not work, check
the efficiency of its fuse: the filament
A
must be intact. If it is not, replace
the blown fuse with another with
the same amperage (same colour).
B
intact fuse.
C
fuse with damaged filament.
To facilitate fuse replacement, use
the pliers
D
hooked to the fuse box
lid on the dashboard left-hand side.
Refer to the tables on the following
pages to identify the protection fuse.
fig. 30
KA00099m
Never replace a fuse
with metal wires
or anything else.
In case of general
protection fuse intervention
(MEGA-FUSE, MIDI-FUSE,
MAXI-FUSE) contact a Ford
Dealership.
WARNING
If a fuse blows again,
contact a Ford Dealership.
WARNING
If the general protection
fuse for safety systems
(air bag system, braking system),
power unit systems (engine system,
transmission system) or steering
system blows, contact a Ford
Dealership.
WARNING
Before replacing a fuse,
make sure that the ignition
key has been removed and that
all the other services are switched
off and/or disengaged.
WARNING
Never replace a fuse
with another with a higher
amp rating; DANGER OF FIRE.
WARNING
105-132 Ford KA EN
14-10-2010
11:37
Pagina 126
127
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
KNOWING
YOUR CAR
IN AN
EMERGENCY
FUSE LOCATION
Dashboard fuses
Left-hand drive versions
To access the fuse you must remove
the press-fitted cover
E
.
The 5-A fuse for door mirror demisting
is located in the diagnostic socket area,
as shown in
fig. 31
.
The control unit show in
fig. 32
is present in the lower area, besides
the pedals.
Right-hand drive versions
To gain access to the fuse box shown
in
fig. 32
, open flap
F
located inside
the glove compartment
fig. 33
.
fig. 31
E
KA00107m
fig. 32
KA00100m
fig. 33
F
KA00125m
105-132 Ford KA EN
14-10-2010
11:37
Pagina 127
128
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
KNOWING
YOUR CAR
IN AN
EMERGENCY
Engine compartment fuse box
fig. 34 and 35
A second fuse box is located on the
right side of the engine compartment,
next to the battery; to access it press
device
I
, release tabs
M
and remove
cover
L
.
The ID number of the electrical
component corresponding to each fuse
can be found on the back of the cover.
fig. 34
fig. 35
KA00101m
KA00102m
If you need to wash
the engine compartment,
take care not to directly
hit the engine compartment
fuse box with the jet of water.
105-132 Ford KA EN
14-10-2010
11:37
Pagina 128
129
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
KNOWING
YOUR CAR
IN AN
EMERGENCY
F12
F13
F31
F32
F36
F37
F38
F43
F47
F48
F49
F50
F51
F53
7,5
7,5
5
7,5
10
5
20
15
20
20
5
7,5
7,5
5
F08
F09
F10
F14
F15
F20
F30
F85
30
15
15
15
20
30
15
15
Engine compartment unit – fig. 35
FUSE
AMPERE
Climate control electric fan
Trailer
Horns
Main beam headlamps
Sun roof motor
Heated rear window, mirror defrosters
Fog lights
Front socket (with or without cigar lighter plug)
FUSE SUMMARY TABLE
Dashboard control unit – fig. 32
FUSE
AMPERE
Right dipped beam power supply
Left dipped headlight and headlight alignment control unit power supply
Remote switch coils on fuse box in engine compartment (INT/A)
Front and rear roof lights, boot and puddle lights
Diagnosis socket, radio, climate control, EOBD
Brake light switch, instrument panel node
Door central locking
Windscreen/rear window washer pump
Driver’s side electric windows
Passenger side electric window
Parking sensor, backlighting switches, electric mirrors
Airbag Control Unit
Radio switch, convergence, climate control, brake lights, clutch
Instrument panel node
105-132 Ford KA EN
14-10-2010
11:37
Pagina 129
146
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
KNOWING
YOUR CAR
SERVICING
AND CARE
SEATS AND FABRIC PARTS
Remove dust with a soft brush or
a vacuum cleaner.
Rub the seats with a sponge moistened
with a solution of water and neutral
detergent.
PLASTIC PARTS
It is advisable to clean interior parts
with a moist cloth and a solution
of water and mild neutral soap.
To remove grease and tough stains,
use products designed specifically for
cleaning plastics. These have no solvents
and have been designed so that they
do not alter the appearance and colour
of the components.
IMPORTANT Never use alcohol or
petroleum to clean the instrument panel.
INTERIORS
Periodically check that water is not
trapped under the mats (due to water
dripping off shoes, umbrellas, etc.)
which could cause oxidisation of
the sheet metal.
Engine compartment
At the end of each winter, thoroughly
wash the engine compartment, taking
care to avoid spraying the water jet
directly onto the electronic control
units and the relay/fuse box on the
left side of the engine compartment
(driving direction). Have this operation
performed at a specialised workshop.
IMPORTANT The washing should
take place with the engine cold and
the ignition key in the
STOP
position.
After the washing operation, make sure
that the various protections (e.g. rubber
caps and guards) have not been
removed or damaged.
Front headlights
IMPORTANT Never use aromatic
substances (e.g.: petrol) or ketenes
(e.g.: acetone) for cleaning front
headlight plastic lens.
Never use flammable
products, such as petrol
ether or rectified petrol to clean
the inside of the car.
The electrostatic charges which
are generated by rubbing during
cleaning may cause a fire.
WARNING
Do not keep aerosol cans
in the vehicle: these could
explode. Aerosol cans must not
be exposed to a temperature
exceeding 50° C. When the vehicle
is exposed to sunlight, inner
temperature can greatly
exceed this value.
WARNING
133-146 Ford KA EN:131-148 Ford KA IT
14-10-2010
11:41
Pagina 146