Ford Windstar - 2003 Fuse Box Diagram

Ford Windstar - 2003 Fuse Box Diagram

Resetting the PSD
The power sliding door may operate incorrectly or not at all because of
the following conditions:
a low voltage or dead battery
disconnecting the battery
if the PSD fuse (fuse #6) is removed or blown. Refer to
Fuses and
relays
in the
Roadside emergencies
chapter.
If any of the above conditions has occured, preform the following steps
to reset the PSD:
1. Check to see if PSD is unlocked and securely closed.
2. Make sure the gearshift is in (P) Park.
3. Push the PSD control on the overhead console to open the door.
4. Wait five (5) seconds and close the door by pressing the PSD control
on the overhead console.
5. Wait five (5) seconds and repeat Steps 3 and 4 then go on to step 6.
6. Repeat steps 3
5 for opposite door.
If the door does not rest in the fully open position, repeat Steps 1
4
again. If the door still does not operate correctly:
7. Turn the ignition switch to OFF.
8. Remove the PSD fuse (fuse #6) from the passenger fuse panel and
leave it out for thirty (30) seconds. Refer to
Fuses and relays
in the
Roadside emergencies
chapter.
9. Reinstall the fuse and wait ten (10) seconds.
10. Repeat steps 1
6 above.
If the door still does not operate correctly, see your dealer for service.
Sliding Door Child Safety Lock
Your vehicle is equipped with a sliding door child safety lock that helps
prevent passengers from operating the sliding door by using the inside
door handle, refer to
Child safety locks
in the
Locks and Security
chapter.
To open the sliding door when the child safety lock is on:
Unlock the sliding door and open the door from the outside.
Press the right or left hand control on the overhead console to open
the door.
Driver Controls
49
AUXILIARY POWER POINT
Power outlets are designed for accessory plugs only. Do not hang
any type of accessory or accessory bracket from the plug.
Improper use of the power outlet can cause damage not covered
by your warranty.
Do not plug optional electrical accessories into the cigarette lighter. Use
the power point.
Do not use the power point for operating the cigarette lighter element.
The Maximum power each power point can supply depends on the fuse
rating. For example: a 20A fuse should supply a maximum of 240 Watts,
a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should
supply a maximum of 120 Watts. Exceeding these limits will result in a
blown fuse.
Always keep the power point caps closed when not being used.
POWER WINDOWS
Press and hold the bottom part of
the rocker switch to open the
window. Press and hold the top part
of the rocker switch to close the
window.
One touch down
Allows the driver
s window to open
fully without holding the control
down. Press completely down on
AUTO and release quickly. Press
again to stop.
Accessory delay
With accessory delay, the window switches may be used for up to ten
minutes after the ignition switch is turned to the OFF position or until
any door is opened.
Driver Controls
50
Do not attempt to service, repair, or modify the air bag
supplemental restraint systems or its fuses. See your Ford or
Lincoln Mercury dealer.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the air bag system, increasing
the risk of injury. Do not modify the front end of the vehicle.
Children and air bags
Children must always be properly
restrained. Accident statistics
suggest that children are safer when
properly restrained in the rear
seating positions than in the front
seating position. Failure to follow
these instructions may increase the
risk of injury in a collision.
Air bags can kill or injure a
child in a child seat.
NEVER
place a rear-facing child
seat in front of an active air bag. If
you must use a forward-facing
child seat in the front seat, move
the seat all the way back.
Determining if the system is operational
The supplemental restraint system uses a warning indicator in the
instrument cluster or a back-up tone to indicate the condition of the
system. Refer to the
Warning light
section in the
Instrument cluster
chapter. Routine maintenance of the air bag is not required.
A difficulty with the system is indicated by one or more of the following:
The readiness light (same light
for front and side air bag system)
will either flash or stay lit.
The readiness light will not
illuminate immediately after ignition is turned on.
Seating and Safety Restraints
113
Do not use accessory seat covers. The use of accessory seat
covers may prevent the deployment of the side air bags and
increase the risk of injury in an accident.
Do not lean your head on the door. The side air bag could injure
you as it deploys from the side of the seatback.
Do not attempt to service, repair, or modify the air bag SRS, its
fuses or the seat cover on a seat containing an air bag. See your
Ford or Lincoln Mercury dealer.
All occupants of the vehicle should always wear their safety belts
even when an air bag SRS is provided.
How does the side air bag system work?
The side air bag system consists of
the following:
An inflatable nylon bag (air bag)
with a gas generator concealed
behind the outboard bolster of
the driver and front passenger
seatbacks.
A special seat cover designed to
allow airbag deployment.
The same warning light,
electronic control and diagnostic
unit as used for the front air
bags.
Two crash sensors located under
the outboard side of the front
seats, attached to the floor.
Side air bags, in combination with seat belts, can help reduce the risk of
severe injuries in the event of a significant side impact collision.
The side air bags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the air bag on the side affected
by the collision will be inflated, even if the respective seat is not
Seating and Safety Restraints
116
AUTOMATIC TRANSAXLE OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed:
1. Apply the parking brake, turn ignition key to LOCK, then remove the
key.
2. Insert the key and turn it to OFF.
Apply the brake pedal and shift
to N (Neutral)
.
In the ignition OFF position, the automatic transmission shift
lever can be moved from the P (Park) position without the brake
pedal depressed. To avoid unwanted vehicle movement, always set the
parking brake.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle
s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your dealer or a qualified service technician.
Driving with an automatic overdrive transaxle with column
gearshift and O/D off switch
Your transaxle is equipped with an adaptive learning strategy found in
the vehicle computer. This feature is designed to increase durability and
Driving
139
This switch is located behind the
service panel on the right side of
the cargo area.
To reset the switch:
1. Turn the ignition OFF.
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the
switch by pushing in on the reset
button.
4. Turn the ignition ON.
5. Wait a few seconds and return
the key to OFF.
6. Make another check of leaks.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
15
Roadside Emergencies
152
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses. To remove
the fuse panel cover, pull up on the latch on the top left side of the
cover.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
Your vehicle is equipped with a Pull Fuse feature that when used, can
extend the duration of your battery life while your vehicle is parked for
long periods of time. This time will be increased from 31 days to 45
55
days (based on option content). You should use this feature when your
vehicle will be parked for long periods of times to ensure the vehicle
starts upon your return.
The pull fuse is located under the instrument panel and is visible from
the exterior of the fuse panel cover.
Roadside Emergencies
153
The fuse holder is designed to allow you to pull the fuse (#6) from the
fuse panel circuit without having to completely remove it from the fuse
panel. The fuse and fuse holder will remain in the fuse panel.
If the fuse (#6) must be replaced, the fuse and fuse holder can be
removed by pulling it completely out from the fuse panel cover.
With the fuse (#6) removed, the following systems will not be functional:
radio
power sliding door(s)
(if equipped)
keyless entry system
(if equipped)
When the pull fuse is reinstalled, the following features will need to be
reset.
radio pre-sets
power sliding door(s)
(if equipped)
Please refer to the
Entertainment
chapter and
Power Sliding Door
section in the
Driver controls
chapter for instructions to reset these
features.
RELAY 1
RELAY 2
RELAY 3
RELAY 4
RELAY 5
RELAY 6
FUSE 1
FUSE 7
FUSE 12
FUSE 18
FUSE 24
FUSE 8
FUSE 13
FUSE 19
FUSE 25
FUSE 9
FUSE 14
FUSE 20
FUSE 26
FUSE 10
FUSE 15
FUSE 21
FUSE 27
FUSE 11
FUSE 16
FUSE 22
FUSE 28
FUSE 17
FUSE 23
FUSE 29
FUSE 2
FUSE 3
FUSE 4
FUSE 5
FUSE 6
Roadside Emergencies
154
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
1
10A
Stepwell lamps, Puddle lamps, 2nd row
reading lamps, 3rd row reading lamps, Cargo
lamp, Dome lamp, Map lamp, Visor/Vanity
lamps, Remote Keyless Entry (RKE) keypad,
Turn signal mirrors
2
25A
I/P Courtesy Lamps, Video Cassette Player
(VCP)
3
15A
Power mirror motors, Adjustable pedal motor,
Memory module (if equipped)
4
Not used
5
20A
Console power point
6
15A
Radio, Compact Disc (CD) changer, RKE
module, Power Sliding Door (PSD) module,
Rear seat radio controller (if equipped), Rear
seat entertainment module (if equipped)
7
15A
Left rear turn lamp, Backup lamps, Right stop
lamp, Right rear park lamp, License Lamps
8
20A
Rear electronic module (RHF/RH sliding/LH
sliding/Liftgate door lock motors, Aux. air
blend door motor, Aux. air mode door motor)
9
10A
Cluster, Powertrain Control Module (PCM)
relay (coil)
10
15A
Heated backlite relay (coil), Speed control
module, Anti-lock Brake System (ABS)
module or IVD Module, Heated seat switch (if
equipped), Heated seat module (if equipped),
Cluster, Front temp blend door actuator,
Brake shift interlock solenoid, PCM, PSD
module, Reverse Sensing System (RSS),
Front A/C control head, Steering wheel angle
sensor (if equipped)
Roadside Emergencies
155
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
11
15A
Electric brake controller, Brake shift interlock
solenoid, Rear electronic module
12
20A
Center high-mounted stop lamp
13
10A
Right rear turn lamp, Left stop lamp, Left
rear park lamp
14
10A
Autolamp sensor, Transmission overdrive
cancel switch, Front electronic module,
Compass module, Electrochromatic mirror,
PSD overhead console switch
15
20A
Console power point
16
10A
Cluster
17
20A
Cigar lighter/Powerpoint, Datalink connector
18
15A
Quarter Window Motors, RH window switch
backlighting, RH lock switch backlighting,
Master control switch (LH) backlighting,
Radio, VCP, Liquid Crystal Display (LCD),
Front electronic module
19
10A
Starter interrupt relay (coil)
20
Not used
21
Not used
22
10A
Heated Mirrors
23
20A
Body power point, Auxiliary blower relay #1
and #2 coils
24
Not used
25
10A
Radio (Anti-theft)
26
10A
Air bag module, Passenger air bag
deactivated indicator, Passenger seat weight
pressure sensor ECU
27
Not used
28
10A
Cluster
29
2A
Speed control deactivation switch
Relay 1
Switched system power relay #4
Roadside Emergencies
156
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
Relay 2
Accessory delay relay
Relay 3
Front blower motor relay
Relay 4
Switched system power relay #3
Relay 5
Rear defrost relay
Relay 6
Auxiliary blower motor relay
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle
s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
Always replace the cover to the power distribution box before
reconnecting the battery or refilling fluid reservoirs
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and specifications
chapter.
The cover for the power distribution box can be removed by releasing
the tab on the back left corner of the cover, then pulling the cover up.
503
304
303
302
301
502
501
207
201
202
203
204
122
118
114
110
106
102
121
117
113
109
105
101
120
116
112
108
104
119
115
111
107
103
24
209
206
208
18
16
14
12
10
8
6
4
2
17
15
13
11
9
7
5
3
1
205
23
22
21
401
20
19
Roadside Emergencies
157
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box Description
1
30A*
Powertrain Control Module (PCM) relay
2
10A*
PCM, Front electronic module (FEM)
3
10A*
A/C compressor clutch
4
25A*
Horns, Horn relay (coil)
5
15A*
Fuel pump motor, PCM
6
30A*
Front wiper motor, Front wiper relay, Front
washer pump, FEM
7
25A*
Rear wiper motor, Rear washer pump, Rear
wiper relay (coil)
8
Not used
9
15A*
Right headlamp
10
15A*
Right front park lamp, Right front turn lamp,
Right front cornering lamp, Right front
auxiliary driving lamp
11
15A*
Left front park lamp, Left front turn lamp,
Left front cornering lamp, Left front auxiliary
driving lamp
12
15A*
Left headlamp (low and high beam)
13
10A*
Alternator field sense
14
10A*
FEM (left door lock motor)
15
20A*
Trailer tow park lamps
16
20A*
Trailer tow turn lamps
17
Not used
18
Not used
19
15A*
AX4S transaxle, Vapor Management Valve
(VMV), A/C clutch relay coil, EGR control
solenoid, Engine fuel control HO2S #11
sensor, Engine fuel control HO2S #21 sensor,
Catalyst monitor HO2S #12 sensor, Catalyst
monitor HO2S #22 Sensor, Canister vent
solenoid, Intake manifold runner control
Roadside Emergencies
158
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box Description
20
15A*
Ignition coil, Intake Air Control (IAC) valve,
Fuel injectors, Mass Air Flow (MAF) sensor,
Fuel pump relay coil, Intake manifold runner
control, High-speed cooling fan relay coil,
Low-speed cooling fan relay coil, PCM,
Passive anti-theft receiver
21
Not used
22
Not used
23
Not used
24
Not used
101
40A**
Anti-lock Brake System (ABS) module or IVD
Module
102
40A**
ABS module or IVD module
103
40A**
SSP4 Relay, SSP4 Relay (coil)
104
30A**
Left-hand power seat motors, Left-hand
power lumbar motor, Driver seat memory
module
105
30A**
Starter motor solenoid, Ignition switch
106
30A**
Delayed accessory relay, Delayed accessory
relay coil, FEM- right-hand front window
motor
107
50A**
Engine cooling fan motors, Cooling fan
dropping resistor
108
Not used
109
30A**
Heated seat modules
110
50A**
Right-hand Power Sliding Door (PSD) module
111
40A**
Fuse junction box
112
30A**
Trailer tow, Electric brake controller
113
30A**
FEM - left-hand window motor
114
40A**
SSP3 relay, SSP3 relay coil
115
50A**
Fuse junction box bus #2
116
30A**
Heated backlight relay
Roadside Emergencies
159
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box Description
117
40A**
Auxiliary blower relay coil, Auxiliary blower
motor
118
50A**
Left-hand PSD module
119
30A**
Fuse junction box bus #1
120
40A**
Front blower relay coil, Front blower motor
121
20A**
Ignition switch, Rear defrost relay coil
122
40A**
Right-hand power seat motors, Right-hand
power lumbar motor
201
Not used
202
Front wiper ON/OFF relay
203
Rear wiper relay
204
A/C clutch relay
205
Horn relay
206
Not used
207
Fuel pump relay
208
Not used
209
Front wiper HI/LO relay
301
Starter interrupt relay
302
High-speed engine cooling fan relay
303
Low-speed engine cooling fan relay
304
PCM Relay
401
Not used
501
PCM diode
502
Not used
503
Not used
* Mini Fuses ** Maxi Fuses
CHANGING A FLAT TIRE
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle
s speed.
hold the steering wheel firmly.
slowly move to a safe place on the side of the road.
Roadside Emergencies
160
With the ON/OFF control in the OFF position, either sliding door can be
operated by pulling the inside or outside handle and sliding the door
back manually. If the vehicle is stopped or parked on a downhill grade,
refer to
Manual sliding door
in this chapter for more information.
If the vehicle is parked on a
downhill grade, the door
could slam shut and could result
in injury or damage to the door.
Ensure that the open door is
secure against the stop before
allowing passengers to enter or
exit the vehicle.
The left hand PSD will not open (manually or power) if the fuel door is
open regardless of the ON/OFF control position.
Safety/Obstructions
If anything obstructs the Power Sliding Door while it is closing, the door
will automatically reverse to the open position, provided it meets
sufficient resistance.
Resetting the PSD
The power sliding door may operate incorrectly or not at all because of
the following conditions:
a low voltage or dead battery
disconnecting the battery
if the PSD fuse (fuse #6) is removed or blown. Refer to
Fuses and
relays
in the
Roadside emergencies
chapter.
If any of the above conditions has occured, preform the following steps
to reset the PSD:
1. Check to see if PSD is unlocked and securely closed.
2. Make sure the gearshift is in (P) Park.
3. Push the PSD control on the overhead console to open the door.
4. Wait five (5) seconds and close the door by pressing the PSD control
on the overhead console.
5. Wait five (5) seconds and repeat Steps 3 and 4 then go on to step 6.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Driver Controls
51
6. Repeat steps 3–5 for opposite door.
If the door does not rest in the fully open position, repeat Steps 1–4
again. If the door still does not operate correctly:
7. Turn the ignition switch to OFF.
8. Remove the PSD fuse (fuse #6) from the passenger fuse panel and
leave it out for thirty (30) seconds. Refer to
Fuses and relays
in the
Roadside emergencies
chapter.
9. Reinstall the fuse and wait ten (10) seconds.
10. Repeat steps 1–6 above.
If the door still does not operate correctly, see your dealer for service.
Sliding Door Child Safety Lock
Your vehicle is equipped with a sliding door child safety lock that helps
prevent passengers from operating the sliding door by using the inside
door handle, refer to
Child safety locks
in the
Locks and Security
chapter.
To open the sliding door when the child safety lock is on:
Unlock the sliding door and open the door from the outside.
Press the right or left hand control on the overhead console to open
the door.
AUXILIARY POWER POINT
Power outlets are designed for accessory plugs only. Do not hang
any type of accessory or accessory bracket from the plug.
Improper use of the power outlet can cause damage not covered
by your warranty.
Do not plug optional electrical accessories into the cigarette lighter. Use
the power point.
Do not use the power point for operating the cigarette lighter element.
The Maximum power each power point can supply depends on the fuse
rating. For example: a 20A fuse should supply a maximum of 240 Watts,
a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should
supply a maximum of 120 Watts. Exceeding these limits will result in a
blown fuse.
Always keep the power point caps closed when not being used.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Driver Controls
52
All occupants of the vehicle, including the driver, should always
properly wear their safety belts, even when an air bag (SRS) is
provided.
Always transport children 12 years old and under in the back
seat and always properly use appropriate child restraints.
The National Highway Traffic Safety Administration (NHTSA)
recommends a minimum distance of at least 25 cm (10 inches)
between an occupant’s chest and the driver air bag module.
Never place your arm over the air bag module as a deploying air
bag can result in serious arm fractures or other injuries.
To properly position yourself away from the air bag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
Do not put anything on or over the air bag module. Placing
objects on or over the air bag inflation area may cause those
objects to be propelled by the air bag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the air bag
supplemental restraint systems or its fuses. See your Ford or
Lincoln Mercury dealer.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the air bag system, increasing
the risk of injury. Do not modify the front end of the vehicle.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Seating and Safety Restraints
113
Do not attempt to service, repair, or modify the air bag SRS, its
fuses or the seat cover on a seat containing an air bag. See your
Ford or Lincoln Mercury dealer.
All occupants of the vehicle should always wear their safety belts
even when an air bag SRS is provided.
How does the side air bag system work?
The side air bag system consists of
the following:
An inflatable nylon bag (air bag)
with a gas generator concealed
behind the outboard bolster of
the driver and front passenger
seatbacks.
A special seat cover designed to
allow airbag deployment.
The same warning light,
electronic control and diagnostic
unit as used for the front air
bags.
Two crash sensors located under
the outboard side of the front
seats, attached to the floor.
Side air bags, in combination with seat belts, can help reduce the risk of
severe injuries in the event of a significant side impact collision.
The side air bags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the air bag on the side affected
by the collision will be inflated, even if the respective seat is not
occupied. The air bag was designed to inflate between the door panel
and occupant to further enhance the protection provided occupants in
side impact collisions.
The air bag SRS is designed to activate when the vehicle sustains lateral
deceleration sufficient to cause the sensors to close an electrical circuit
that initiates air bag inflation.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Seating and Safety Restraints
117
If the steering wanders or pulls, check for:
an improperly inflated tire
uneven tire wear
loose or worn suspension components
loose or worn steering components
improper steering alignment
AUTOMATIC TRANSAXLE OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed:
1. Apply the parking brake, turn ignition key to LOCK, then remove the
key.
2. Insert the key and turn it to OFF.
Apply the brake pedal and shift
to N (Neutral)
.
When the key is in the ignition OFF position, the automatic
transmission shift lever can be moved from the P (Park) position
without the brake pedal depressed. To avoid unwanted vehicle
movement, always set the parking brake.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Driving
140
This switch is located behind the
service panel on the right side of
the cargo area.
To reset the switch:
1. Turn the ignition OFF.
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the
switch by pushing in on the reset
button.
4. Turn the ignition ON.
5. Wait a few seconds and return
the key to OFF.
6. Make another check of leaks.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
15
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
154
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses. To remove
the fuse panel cover, pull up on the latch on the top left side of the
cover.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
Your vehicle is equipped with a Pull Fuse feature that when used, can
extend the duration of your battery life while your vehicle is parked for
long periods of time. This time will be increased from 31 days to 45 – 55
days (based on option content). You should use this feature when your
vehicle will be parked for long periods of times to ensure the vehicle
starts upon your return.
The pull fuse is located under the instrument panel and is visible from
the exterior of the fuse panel cover.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
155
The fuse holder is designed to allow you to pull the fuse (#6) from the
fuse panel circuit without having to completely remove it from the fuse
panel. The fuse and fuse holder will remain in the fuse panel.
If the fuse (#6) must be replaced, the fuse and fuse holder can be
removed by pulling it completely out from the fuse panel cover.
With the fuse (#6) removed, the following systems will not be functional:
radio
power sliding door(s) – (if equipped)
keyless entry system– (if equipped)
When the pull fuse is reinstalled, the following features will need to be
reset.
radio pre-sets
power sliding door(s) – (if equipped)
Please refer to the
Entertainment
chapter and
Power Sliding Door
section in the
Driver controls
chapter for instructions to reset these
features.
RELAY 1
RELAY 2
RELAY 3
RELAY 4
RELAY 5
RELAY 6
FUSE 1
FUSE 7
FUSE 12
FUSE 18
FUSE 24
FUSE 8
FUSE 13
FUSE 19
FUSE 25
FUSE 9
FUSE 14
FUSE 20
FUSE 26
FUSE 10
FUSE 15
FUSE 21
FUSE 27
FUSE 11
FUSE 16
FUSE 22
FUSE 28
FUSE 17
FUSE 23
FUSE 29
FUSE 2
FUSE 3
FUSE 4
FUSE 5
FUSE 6
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
156
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
10A
Stepwell lamps, Puddle lamps,
2nd row reading lamps, 3rd row
reading lamps, Cargo lamp, Dome
lamp, Map lamp, Visor/Vanity
lamps, Remote Keyless Entry
(RKE) keypad, Turn signal
mirrors
2
25A
I/P Courtesy Lamps, Video
Cassette Player (VCP)
3
15A
Power mirror motors, Adjustable
pedal motor, Memory module (if
equipped)
4
Not used
5
20A
Console power point
6
15A
Radio, Compact Disc (CD)
changer, RKE module, Power
Sliding Door (PSD) module, Rear
seat radio controller (if
equipped), Rear seat
entertainment module (if
equipped)
7
15A
Left rear turn lamp, Backup
lamps, Right stop lamp, Right rear
park lamp, License Lamps
8
20A
Rear electronic module (RHF/RH
sliding/LH sliding/Liftgate door
lock motors, Aux. air blend door
motor, Aux. air mode door motor)
9
10A
Cluster, Powertrain Control
Module (PCM) relay (coil)
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
157
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
10
15A
Heated backlite relay (coil),
Speed control module, Anti-lock
Brake System (ABS) module or
IVD Module, Heated seat switch
(if equipped), Heated seat module
(if equipped), Cluster, Front temp
blend door actuator, Brake shift
interlock solenoid, PCM, PSD
module, Reverse Sensing System
(RSS), Front A/C control head,
Steering wheel angle sensor (if
equipped)
11
15A
Electric brake controller, Brake
shift interlock solenoid, Rear
electronic module
12
20A
Center high-mounted stop lamp
13
10A
Right rear turn lamp, Left stop
lamp, Left rear park lamp
14
10A
Autolamp sensor, Transmission
overdrive cancel switch, Front
electronic module, Compass
module, Electrochromatic mirror,
PSD overhead console switch
15
20A
Console power point
16
10A
Cluster
17
20A
Cigar lighter/Powerpoint, Datalink
connector
18
15A
Quarter Window Motors, RH
window switch backlighting, RH
lock switch backlighting, Master
control switch (LH) backlighting,
Radio, VCP, Liquid Crystal Display
(LCD), Front electronic module
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
158
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
19
10A
Starter interrupt relay (coil)
20
Not used
21
Not used
22
10A
Heated Mirrors
23
20A
Body power point, Auxiliary
blower relay #1 and #2 coils
24
Not used
25
10A
Radio (Anti-theft)
26
10A
Air bag module, Passenger air bag
deactivated indicator, Passenger
seat weight pressure sensor ECU
27
Not used
28
10A
Cluster
29
2A
Speed control deactivation switch
Relay 1
Switched system power relay #4
Relay 2
Accessory delay relay
Relay 3
Front blower motor relay
Relay 4
Switched system power relay #3
Relay 5
Rear defrost relay
Relay 6
Auxiliary blower motor relay
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
Always replace the cover to the power distribution box before
reconnecting the battery or refilling fluid reservoirs
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and specifications
chapter.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
159
The cover for the power distribution box can be removed by releasing
the tab on the back left corner of the cover, then pulling the cover up.
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
30A*
Powertrain Control Module (PCM)
relay
2
10A*
PCM, Front electronic module (FEM)
3
10A*
A/C compressor clutch
4
25A*
Horns, Horn relay (coil)
5
15A*
Fuel pump motor, PCM
6
30A*
Front wiper motor, Front wiper relay,
Front washer pump, FEM
7
25A*
Rear wiper motor, Rear washer
pump, Rear wiper relay (coil)
8
Not used
9
15A*
Right headlamp
503
304
303
302
301
502
501
207
201
202
203
204
122
118
114
110
106
102
121
117
113
109
105
101
120
116
112
108
104
119
115
111
107
103
24
209
206
208
18
16
14
12
10
8
6
4
2
17
15
13
11
9
7
5
3
1
205
23
22
21
401
20
19
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
160
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
10
15A*
Right front park lamp, Right front
turn lamp, Right front cornering
lamp, Right front auxiliary driving
lamp
11
15A*
Left front park lamp, Left front turn
lamp, Left front cornering lamp, Left
front auxiliary driving lamp
12
15A*
Left headlamp (low and high beam)
13
10A*
Alternator field sense
14
10A*
FEM (left door lock motor)
15
20A*
Trailer tow park lamps
16
20A*
Trailer tow turn lamps
17
Not used
18
Not used
19
15A*
AX4S transaxle, Vapor Management
Valve (VMV), A/C clutch relay coil,
EGR control solenoid, Engine fuel
control HO2S #11 sensor, Engine fuel
control HO2S #21 sensor, Catalyst
monitor HO2S #12 sensor, Catalyst
monitor HO2S #22 Sensor, Canister
vent solenoid, Intake manifold runner
control
20
15A*
Ignition coil, Intake Air Control (IAC)
valve, Fuel injectors, Mass Air Flow
(MAF) sensor, Fuel pump relay coil,
Intake manifold runner control,
High-speed cooling fan relay coil,
Low-speed cooling fan relay coil,
PCM, Passive anti-theft receiver
21
Not used
22
Not used
23
Not used
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
161
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
24
Not used
101
40A**
Anti-lock Brake System (ABS)
module or IVD Module
102
40A**
ABS module or IVD module
103
40A**
SSP4 Relay, SSP4 Relay (coil)
104
30A**
Left-hand power seat motors,
Left-hand power lumbar motor,
Driver seat memory module
105
30A**
Starter motor solenoid, Ignition
switch
106
30A**
Delayed accessory relay, Delayed
accessory relay coil, FEM- right-hand
front window motor
107
50A**
Engine cooling fan motors, Cooling
fan dropping resistor
108
Not used
109
30A**
Heated seat modules
110
50A**
Right-hand Power Sliding Door
(PSD) module
111
40A**
Fuse junction box
112
Trailer tow - electric brake controller
(customer access)
113
30A**
FEM - left-hand window motor
114
40A**
SSP3 relay, SSP3 relay coil
115
50A**
Fuse junction box bus #2
116
30A**
Heated backlight relay
117
40A**
Auxiliary blower relay coil, Auxiliary
blower motor
118
50A**
Left-hand PSD module
119
30A**
Fuse junction box bus #1
120
40A**
Front blower relay coil, Front blower
motor
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
162
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
121
20A**
Ignition switch, Rear defrost relay
coil
122
40A**
Right-hand power seat motors,
Right-hand power lumbar motor
201
Not used
202
Front wiper ON/OFF relay
203
Rear wiper relay
204
A/C clutch relay
205
Horn relay
206
Not used
207
Fuel pump relay
208
Not used
209
Front wiper HI/LO relay
301
Starter interrupt relay
302
High-speed engine cooling fan relay
303
Low-speed engine cooling fan relay
304
PCM Relay
401
Not used
501
PCM diode
502
Not used
503
Not used
* Mini Fuses ** Maxi Fuses
CHANGING A FLAT TIRE
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle’s speed.
hold the steering wheel firmly.
slowly move to a safe place on the side of the road.
If your low tire warning light is on, refer to
Low tire warning
in the
Maintenance and specifications
chapter.
2003 Windstar
(win)
Owners Guide (post-2002-fmt)
USA English
(fus)
Roadside Emergencies
163