Ford Taurus - 2002 Fuse Box Diagram

Ford Taurus - 2002 Fuse Box Diagram

Your vehicle has a factory-set 5–digit code that operates the keyless
entry system. You can also program your own 5–digit personal entry
code.
The factory-set code is located:
on the owner’s wallet card in the glove compartment
on the inner side of the passenger compartment fuse box
or at your dealer
When pressing the controls on the keyless entry keypad, press the
middle of the controls to ensure a good activation.
Programming your own personal entry code
1. Enter the factory-set code (keypad will illuminate when pressed).
2. Press the 1/2 control within five
seconds of step 1.
3. Enter your personal 5 digit code.
Enter each digit within five seconds
of the previous one. The power door
locks should cycle (lock/unlock) to
confirm your personal code is
accepted.
Do not set a code that includes three of the same number or presents
them in sequential order. Thieves can easily figure out these types of
codes.
Your personal code does not replace the permanent code that the
dealership gave you. You can use either code to unlock your vehicle. If a
second personal code is entered, the module will erase the first personal
code in favor of the new code.
To exit, press 7/8 and 9/0 simultaneously or allow more than 5 seconds
to elapse since a button press occured and the 5 digit keycode will be
programed.
1
2
3
4
5
6
7
8
9
0
Locks and Security
92
Steps you can take to properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly (one or two degrees) from the upright
position.
Do not put anything on or over the air bag module. Placing
objects on or over the air bag inflation area may cause those
objects to be propelled by the air bag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the Air Bag
Supplemental Restraint System or its fuses. See your Ford or
Lincoln Mercury dealer.
The front passenger air bag is not designed to offer protection to
occupants in the center front seating position.
Modifications to the front end of the vehicle, including frame,
bumper, front end body structure and tow hooks may affect the
performance of the air bag sensors increasing the risk of injury. Do not
modify the front end of the vehicle.
Seating and Safety Restraints
123
A difficulty with the system is indicated by one or more of the following:
The readiness light (same light
for front and side air bag system)
will either flash or stay lit.
The readiness light will not
illuminate immediately after ignition is turned on.
A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and/or light are repaired.
If any of these things happen, even intermittently, have the supplemental
restraint system serviced at your dealership or by a qualified technician
immediately. Unless serviced, the system may not function properly in
the event of a collision.
Side air bag system (if equipped)
Do not place objects or mount equipment on or near the air bag
cover on the side of the seatbacks of the front seats or in front
seat areas that may come into contact with a deploying air bag. Failure
to follow these instructions may increase the risk of personal injury in
the event of a collision.
Do not use accessory seat covers. The use of accessory seat
covers may prevent the deployment of the side air bags and
increase the risk of injury in an accident.
Do not lean your head on the door. The side air bag could injure
you as it deploys from the side of the seatback.
Do not attempt to service, repair, or modify the air bag
supplemental restraint system, its fuses or the seat cover on a
seat containing an air bag. See your Ford or Lincoln Mercury dealer.
All occupants of the vehicle including the driver should always
wear their safety belts even when an air bag SRS is provided.
Seating and Safety Restraints
126
high crown in center of road
high crosswinds
wheels out of alignment
loose or worn suspension components
AUTOMATIC TRANSAXLE OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed:
1. Apply the parking brake, turn ignition key to LOCK, then remove the
key.
2. Insert the key and turn it to OFF. Apply the brake pedal and shift to N
(Neutral).
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
If your vehicle gets stuck in mud or snow, it may be rocked out by
shifting from forward and reverse gears while stopping between shifts, in
a steady pattern. Press lightly on the accelerator in each gear. If
necessary, try turning the Traction Control
y
system off. This will allow
the wheels to spin, which may help to free your stuck vehicle. For more
information, refer to
Traction Control
y
(if equipped)
in this chapter.
Do not rock the vehicle if the engine is not at normal operating
temperature or damage to the transaxle may occur.
Do not rock the vehicle for more than a few minutes or damage
to the transaxle and tires may occur or the engine may overheat.
Driving
148
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
Maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Amber
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
15
Roadside Emergencies
162
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
The fuses are coded as follows.
Fuse/relay
location
Fuse amp
rating
Passenger compartment fuse
panel description
1
Accessory delay relay
2
Driver one touch down relay
3
Blower motor relay
4
Flasher relay
5
Not used
6
Not used
7
40A
Rear defrost grid feed
8
40A
Blower motor
9
Rear defrost relay
10
30A
Circuit breaker: Power seats,
Delayed accessory, Adjustable
pedals
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
33
35
36
37
38
39
40
41
42
PULL TAB
TO RELEASE
SEE OWNERS MANUAL
CONSULTER LA GUIDE
Roadside Emergencies
163
Fuse/relay
location
Fuse amp
rating
Passenger compartment fuse
panel description
11
15A
Integrated control panel (ICP),
Rear washer wiper control, Front
washer, Cell phone, Passenger
switch illumination, GEM, Rear
wiper motor
12
10A
Heated mirrors, Rear defrost
switch
13
20A
Power point
14
Not used
15
30A
Front wiper motor
16
15A
Flasher and GEM power,
Integrated control panel (ICP)
power, RCC memory, Cluster
17
15A
Stop lamp, Speed control
deactivating switch
18
Not used
19
Not used
20
Not used
21
Not used
22
20A
Deck lid release solenoid,
Lock/unlock relays
23
10A
Air bag module, PATS transceiver
24
15A
Transit relay
25
2A
PCM relay, Fuel pump relay
26
10A
Mirrors, Power antenna, Pulse
stretcher module, Deck lid lamp,
Battery saver
27
10A
Gauges and warning lamps,
Integrated control panel (ICP),
FFV sender, GEM
28
10A
Blower motor relay coil, EATC
logic, Puddle lamps
Roadside Emergencies
164
Fuse/relay
location
Fuse amp
rating
Passenger compartment fuse
panel description
29
15A
Autolamps, Park lamps, PWM,
Headlamp switch
30
15A
Horns and horn switch, OBD II
connector
31
Not used
32
10A
ABS, DRL relay coil, Speed
control actuator, Traction control
switch, AC heater selector switch,
Blend door actuator, Brake shift
interlock, Rear defroster relay coil
33
Not used
34
Not used
35
Not used
36
15A
Turn signals, Back-up lamps
37
15A
Transmission position switch
38
5A
GEM park neutral switch
39
Not used
40
Not used
41
Not used
42
Not used
Roadside Emergencies
165
Power distribution box
The power distribution box is
located in the engine compartment.
The power distribution box contains
high-current fuses that protect your
vehicle’s main electrical systems
from overloads.
Always disconnect the battery before servicing high current
fuses.
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and specifications
chapter.
The high-current fuses are coded as follows.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 22
23
24
25
29
30
26
27
28
31
32
33
Roadside Emergencies
166
Fuse/relay
location
Fuse amp
rating
Power distribution box
description
1
60A**
Fuse junction panel
2
30A**
PCM relay
3
60A**
Fuse junction panel
4
Not used
5
Not used
6
Not used
7
40A**
Starter relay, Ignition switch
8
20A**
Transit relay (export only)
9
40A**
Cooling fan relays
10
Not used
11
Not used
12
Not used
13
40A**
Anti-lock brake module pump
feed
14
Not used
15
20A*
Anti-lock brake module valve
solenoid
16
20A*
Fuel pump relay
17
20A*
Cell port
18
20A*
Cigar lighter
19
15A*
Right headlamp
20
Not used
21
15 A*
Left headlamp
22
10A*
A/C clutch relay, PCM keep alive
power
23
Starter motor relay
24
Fan relay
25
Wiper speed relay
26
10A*
Alternator
27
5A*
Rear control unit, Antenna
Roadside Emergencies
167
Fuse/relay
location
Fuse amp
rating
Power distribution box
description
28
15A*
HEGO sensor transmission shift
solenoid, Canister vent, A/C
clutch relay
29
Wiper park relay
30
Fuel pump relay
31
PCM power relay
32
Fan relay
33
A/C clutch relay
* Mini Fuses ** Maxi Fuses
Relays
Relays are located in the power distribution box and should be replaced
by qualified technicians.
CHANGING THE TIRES
If you get a flat tire while driving, do not apply the brake heavily.
Instead, gradually decrease your speed. Hold the steering wheel firmly
and slowly move to a safe place on the side of the road.
Temporary spare tire information
The temporary spare tire for your vehicle is labeled as such. It is smaller
than a regular tire and is designed for emergency use only.
If you use the temporary spare tire continuously or do not follow
these precautions, the tire could fail, causing you to lose control
of the vehicle, possibly injuring yourself or others.
When driving with the temporary spare tire
do not:
exceed 80 km/h (50 mph) under any circumstances
load the vehicle beyond maximum vehicle load rating listed on the
Safety Compliance Label
tow a trailer
use tire chains
Roadside Emergencies
168
Your vehicle has a factory-set 5–digit code that operates the keyless
entry system. You can also program your own 5–digit personal entry
code.
The factory-set code is located:
on the owner’s wallet card in the glove compartment
on the inner side of the passenger compartment fuse box
or at your dealer
When pressing the controls on the keyless entry keypad, press the
middle of the controls to ensure a good activation.
Programming your own personal entry code
1. Enter the factory-set code (keypad will illuminate when pressed).
2. Press the 1/2 control within five
seconds of step 1.
3. Enter your personal 5 digit code.
Enter each digit within five seconds
of the previous one. The power door
locks should cycle (lock/unlock) to
confirm your personal code is
accepted.
Do not set a code that includes three of the same number or presents
them in sequential order. Thieves can easily figure out these types of
codes.
Your personal code does not replace the permanent code that the
dealership gave you. You can use either code to unlock your vehicle. If a
second personal code is entered, the module will erase the first personal
code in favor of the new code.
To exit, press 7/8 and 9/0 simultaneously or allow more than 5 seconds
to elapse since a button press occured and the 5 digit keycode will be
programed.
1
2
3
4
5
6
7
8
9
0
Locks and Security
94
Recline the seat slightly (one or two degrees) from the upright
position.
Do not put anything on or over the air bag module. Placing
objects on or over the air bag inflation area may cause those
objects to be propelled by the air bag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the Air Bag
Supplemental Restraint System or its fuses. See your Ford or
Lincoln Mercury dealer.
The front passenger air bag is not designed to offer protection to
an occupant in the center front seating position.
Modifications to the front end of the vehicle, including frame,
bumper, front end body structure and tow hooks may affect the
performance of the air bag sensors increasing the risk of injury. Do not
modify the front end of the vehicle.
Seating and Safety Restraints
125
A difficulty with the system is indicated by one or more of the following:
The readiness light (same light
for front and side air bag system)
will either flash or stay lit.
The readiness light will not
illuminate immediately after ignition is turned on.
A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and/or light are repaired.
If any of these things happen, even intermittently, have the supplemental
restraint system serviced at your dealership or by a qualified technician
immediately. Unless serviced, the system may not function properly in
the event of a collision.
Side air bag system (if equipped)
Do not place objects or mount equipment on or near the air bag
cover on the side of the seatbacks of the front seats or in front
seat areas that may come into contact with a deploying air bag. Failure
to follow these instructions may increase the risk of personal injury in
the event of a collision.
Do not use accessory seat covers. The use of accessory seat
covers may prevent the deployment of the side air bags and
increase the risk of injury in an accident.
Do not lean your head on the door. The side air bag could injure
you as it deploys from the side of the seatback.
Do not attempt to service, repair, or modify the air bag
supplemental restraint system, its fuses or the seat cover on a
seat containing an air bag. See your Ford or Lincoln Mercury dealer.
All occupants of the vehicle including the driver should always
wear their safety belts even when an air bag SRS is provided.
Seating and Safety Restraints
128
STEERING
Your vehicle is equipped with power steering. Power steering uses energy
from the engine to decrease the driver’s effort in steering the vehicle.
To prevent damage to the power steering pump:
Never hold the steering wheel to the extreme right or the extreme left
for more than a few seconds when the engine is running.
Do not operate the vehicle with the power steering pump fluid level
below the MIN mark on the reservoir.
If the power steering system breaks down (or if the engine is turned
off), you can steer the vehicle manually, but it takes more effort.
If the steering wanders or pulls, the condition could be caused by any of
the following:
underinflated tire(s) on any wheel(s)
uneven vehicle loading
high crown in center of road
high crosswinds
wheels out of alignment
loose or worn suspension components
AUTOMATIC TRANSAXLE OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed:
1.
Apply the parking brake, turn ignition key to LOCK, then remove the key.
2. Insert the key and turn it to OFF. Apply the brake pedal and shift to N
(Neutral).
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
emergencies
chapter.
Driving
150
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
Maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Amber
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
15
Roadside Emergencies
165
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
The fuses are coded as follows.
Fuse/relay
location
Fuse amp
rating
Passenger compartment fuse panel
description
1
Accessory delay relay
2
Driver one touch down relay
3
Blower motor relay
4
Flasher relay
5
Not used
6
Not used
7
40A
Rear defrost grid feed
8
40A
Blower motor
9
Rear defrost relay
10
30A
Circuit breaker: Power seats, Delayed
accessory, Adjustable pedals
11
15A
Integrated control panel (ICP), Rear
washer wiper control, Front washer, Cell
phone, Passenger switch illumination,
GEM, Rear wiper motor
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
33
35
36
37
38
39
40
41
42
PULL TAB
TO RELEASE
SEE OWNERS MANUAL
CONSULTER LA GUIDE
Roadside Emergencies
166
Fuse/relay
location
Fuse amp
rating
Passenger compartment fuse panel
description
12
10A
Heated mirrors, Rear defrost switch
13
20A
Power point
14
Not used
15
30A
Front wiper motor
16
15A
Flasher and GEM power, Integrated
control panel (ICP) power, RCC memory,
Cluster
17
15A
Stop lamp, Speed control deactivating
switch
18
Not used
19
Not used
20
Not used
21
Not used
22
20A
Deck lid release solenoid, Lock/unlock
relays
23
10A
Air bag module, PATS transceiver
24
15A
Transit relay
25
2A
PCM relay, Fuel pump relay
26
10A
Mirrors, Power antenna, Pulse stretcher
module, Deck lid lamp, Battery saver
27
10A
Gauges and warning lamps, Integrated
control panel (ICP), FFV sender, GEM
28
10A
Blower motor relay coil, EATC logic,
Puddle lamps
29
15A
Autolamps, Park lamps, PWM, Headlamp
switch
30
15A
Horns and horn switch, OBD II connector
31
Not used
Roadside Emergencies
167
Fuse/relay
location
Fuse amp
rating
Passenger compartment fuse panel
description
32
10A
ABS, DRL relay coil, Speed control
actuator, Traction control switch, AC
heater selector switch, Blend door
actuator, Brake shift interlock, Rear
defroster relay coil
33
Not used
34
Not used
35
Not used
36
15A
Turn signals, Back-up lamps
37
15A
Transmission position switch
38
5A
GEM park neutral switch
39
Not used
40
Not used
41
Not used
42
Not used
Power distribution box
The power distribution box is
located in the engine compartment.
The power distribution box contains
high-current fuses that protect your
vehicle’s main electrical systems
from overloads.
Always disconnect the battery before servicing high current
fuses.
Roadside Emergencies
168
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and specifications
chapter.
The high-current fuses are coded as follows.
Fuse/relay
location
Fuse amp
rating
Power distribution box description
1
60A**
Fuse junction panel
2
30A**
PCM relay
3
60A**
Fuse junction panel
4
Not used
5
Not used
6
Not used
7
40A**
Starter relay, Ignition switch
8
20A**
Transit relay (export only)
9
40A**
Cooling fan relays
10
Not used
11
Not used
12
Not used
13
40A**
Anti-lock brake module pump feed
14
Not used
15
20A*
Anti-lock brake module valve solenoid
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 22
23
24
25
29
30
26
27
28
31
32
33
Roadside Emergencies
169
Fuse/relay
location
Fuse amp
rating
Power distribution box description
16
20A*
Fuel pump relay
17
20A*
Cell port
18
20A*
Cigar lighter
19
15A*
Right headlamp
20
Not used
21
15 A*
Left headlamp
22
10A*
A/C clutch relay, PCM keep alive power
23
Starter motor relay
24
Fan relay
25
Wiper speed relay
26
10A*
Alternator
27
5A*
Rear control unit, Antenna
28
15A*
HEGO sensor transmission shift solenoid,
Canister vent, A/C clutch relay
29
Wiper park relay
30
Fuel pump relay
31
PCM power relay
32
Fan relay
33
A/C clutch relay
* Mini Fuses ** Maxi Fuses
Relays
Relays are located in the power distribution box and should be replaced
by qualified technicians.
CHANGING THE TIRES
If you get a flat tire while driving, do not apply the brake heavily.
Instead, gradually decrease your speed. Hold the steering wheel firmly
and slowly move to a safe place on the side of the road.
Temporary spare tire information
The temporary spare tire for your vehicle is labeled as such. It is smaller
than a regular tire and is designed for emergency use only.
Roadside Emergencies
170