Ford Mustang - 1996 Fuse Box Diagram

Ford Mustang - 1996 Fuse Box Diagram

28
A problem with the system is indicated by one
or more of the following:
the readiness light will either flash or stay lit,
or
it will not light immediately after the ignition
is turned on, or
a group of five beeps will be heard.
If any of these things happen, have the air bag
system serviced at your Ford or Lincoln-Mercury
dealer immediately. Unless serviced, the air bag
Supplemental Restraint System may not function
properly in the event of a collision.
R
WARNING
Do not attempt to service, repair, or
modify the Air Bag Supplemental
Restraint System or its fuses. See your
Ford or Lincoln-Mercury dealer.
Disposal of air bags or air bag equipped
vehicles
For disposal of air bags or air bag equipped
vehicles, see your local Ford or Lincoln-Mercury
dealer. Air bags
MUST
be disposed of by
qualified personnel.
Safety Restraints for Children
In the U.S. and Canada, you are required by law
to use safety restraints for children. If small
children ride in your vehicle — this generally
includes children who are four years old or
younger and who weigh 40 pounds (18 kg) or
less — you must put them in safety seats that
are made specially for children. Safety belts
alone do not provide maximum protection for
these children. Check your local and state laws
for specific requirements.
178
3.
Move the gearshift lever out of P (Park).
Your vehicle is equipped with a Brake Shift
Interlock safety feature. This feature prevents the
gearshift from being moved from the P (Park)
position until the brake pedal is depressed. This
feature is active when the ignition is in the ON
position. If the gearshift lever CANNOT be
moved from P (Park) with the brake pedal
depressed:
1.
Turn the engine off and remove the ignition
key.
2.
Apply parking brake.
3.
Reinsert the ignition key and turn clockwise
to the first position (OFF).
4.
Depress the brake pedal, move the gearshift
lever to N (Neutral) and start the engine.
R
WARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titled
Servicing Your Mustang
in this Owner Guide for instructions on checking
and replacing fuses.
The console-mounted gearshift will lock in P
(Park) when you turn the key to the LOCK
position. When the gearshift is in any position
except P (Park), the ignition key cannot be
turned to LOCK or removed from the steering
column. TO REMOVE THE KEY, the gearshift
lever must be in P (Park).
278
Fluid level for power steering
Use only power steering fluid that meets Ford
Specification Mercon
H
ATF XT-2-QDX.
NOTE:
If the power steering fluid is low, do
not drive your vehicle for a long
period of time before adding fluid.
This can damage the power steering
pump.
Fuses, High Current Fuses and
Circuit Breakers
Fuses (conventional and high current) and circuit
breakers protect your vehicle’s wiring system
from overloading. If electrical parts in your
vehicle are not working, the system may have
been overloaded and blown a fuse or tripped a
circuit breaker. Before you replace or repair any
electrical parts, check the appropriate fuses
(conventional and high current) or circuit
breakers.
279
The following charts tell you which fuses or
circuit breakers protect the wiring for each
electrical part of your vehicle. If a fuse blows or
a circuit breaker opens a circuit,
all
the parts of
your vehicle that use that circuit will not work.
Once you have determined which fuses or circuit
breakers to check, follow the procedures under
Checking and replacing fuses
or
Checking and
replacing circuit breakers
in this chapter.
The instrument panel fuse panel location
280
The instrument panel fuse panel
281
The Instrument Panel Fuses, Circuit
Breakers and Relays
282
High Current Fuses
High current fuses are circuit protectors that are
part of the wiring harness for some electrical
equipment. These, like fuses, open when the
circuit load exceeds their amperage rating. High
current fuses may be purchased from your Ford
or Lincoln-Mercury dealer.
The high current fuse panel is located in the
engine compartment on the left-hand fender
apron.
283
R
WARNING
Always disconnect the battery before
servicing high current fuses.
Ford recommends that high current fuses be
replaced by a qualified technician.
The high current fuse panel location
284
The high current fuse panel
285
The high current fuses and relays
287
Checking and Replacing Fuses
If you need to check a fuse, follow these steps:
1.
Find the fuse panel cover below and to left
of the steering column, in the instrument
panel. Pull outward on the handle below the
word “fuses” to expose the fuse panel.
Squeeze the two backing tabs and pull to
remove the cover.
2.
On the fuse panel cover, find the number of
the fuse you want to check. The following
fuse panel cover tells you where to locate
the fuse on the panel.
3.
Check the fuse to see if it is blown. Look
through the clear side of the fuse to see if
the metal wire inside is separated. If it is,
the fuse should be replaced.
The side view of a fuse
4.
Replace the fuse with one that has the right
amperage rating. (See the following chart.)
288
R
WARNING
Always replace a fuse with one that has
the specified amperage rating. Using a
fuse with a higher amperage rating can
cause severe wire damage and could start
a fire.
5.
Replace the cover.
Even after you replace a fuse, it will continue to
blow if you do not find what caused the
overload. If the fuse continues to blow, have
your electrical system checked.
Circuit Breakers
If you need to check a circuit breaker that is on
the fuse panel, see
Checking and replacing fuses
in
this chapter to find out how to locate the fuse
panel.
Circuit breakers will reset themselves and allow
the electrical parts to work again once the
overload on the circuit is removed. If the circuit
breakers continue to cut off electricity, have your
vehicle’s electrical system checked.
Diagnostic equipment is needed to check circuit
breakers. Refer to the manufacturer’s
instructions.
If you replace a circuit breaker, use one with the
same amperage rating. To remove a circuit
breaker mounted in the fuse panel, grip it with
your finger and thumb and pull it straight out
of its socket.