Ford Mountaineer - 2010 Fuse Box Diagram

Ford Mountaineer - 2010 Fuse Box Diagram

The rear side of the console may incorporate the following features:
Air vents
Cupholders
WARNING:
Use only soft cups in the cupholder. Hard objects
can injure you in a collision.
Rear center console features (if equipped)
The rear center console incorporates the following features:
Utility compartment
Cupholders
Flip forward armrest to provide a
flat load floor
AUXILIARY POWER POINTS (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
Auxiliary power points can be found in the following locations:
On the front of the center console
Inside the utility compartment
On the rear of the console, accessible from the rear seats
Do not use the power point for operating the cigarette lighter element (if
equipped).
Driver Controls
112
To prevent the fuse from being blown, do not use the power point(s)
over the vehicle capacity of 12 VDC/180W. If the power point or cigar
lighter socket is not working, a fuse may have blown. Refer to
Fuses and
relays
in the
Roadside Emergencies
chapter for information on
checking and replacing fuses.
To have full capacity usage of your power point, the engine is required to
be running to avoid unintentional discharge of the battery. To prevent
the battery from being discharged:
do not use the power point longer than necessary when the engine is
not running,
do not leave battery chargers, video game adapters, computers and
other devices plugged in overnight or when the vehicle is parked for
extended periods.
Always keep the power point caps closed when not being used.
POWER WINDOWS
WARNING:
Do not leave children unattended in the vehicle and
do not let children play with the power windows. They may
seriously injure themselves.
WARNING:
When closing the power windows, you should verify
they are free of obstructions and ensure that children and/or
pets are not in the proximity of the window openings.
Press and pull the window switches
to open and close windows.
Press down (to the first detent)
and hold the switch to open.
Pull up (to the first detent) and
hold the switch to close.
Rear Window Buffeting:
When one or both of the rear windows are
open, the vehicle may demonstrate a wind throb or buffeting noise. This
noise can be alleviated by lowering a front window approximately two to
three inches.
One touch up or down (Driver’s window only) (if equipped)
This feature allows the driver’s window to open or close fully without
holding the control down.
Driver Controls
113
WARNING:
Never place your arm over the airbag module as a
deploying airbag can result in serious arm fractures or other
injuries.
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
WARNING:
Do not put anything on or over the airbag module.
Placing objects on or over the airbag inflation area may cause
those objects to be propelled by the airbag into your face and torso
causing serious injury.
WARNING:
Do not attempt to service, repair, or modify the
airbag supplemental restraint systems or its fuses. Contact your
authorized dealer as soon as possible.
WARNING:
Modifications to the front end of the vehicle,
including frame, bumper, front end body structure and non-Ford
tow hooks may effect the performance of the airbag sensors increasing
the risk of injury. Do not modify the front end of the vehicle with
anything other than authorized Ford accessories for your vehicle.
WARNING:
Additional equipment may affect the performance of
the airbag sensors increasing the risk of injury.
Seating and Safety Restraints
191
A difficulty with the system is indicated by one or more of the following:
The readiness light will either
flash or stay lit.
The readiness light will not
illuminate immediately after
ignition is turned on.
A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and/or light are repaired.
If any of these things happen, even intermittently, contact your
authorized dealer as soon as possible. Unless serviced, the system may
not function properly in the event of a collision.
Seat-mounted side airbag system
WARNING:
Do not place objects or mount equipment on or
near the airbag cover on the side of the seatbacks of the front
seats or in front seat areas that may come into contact with a
deploying airbag. Failure to follow these instructions may increase the
risk of personal injury in the event of a collision.
WARNING:
Do not use accessory seat covers. The use of
accessory seat covers may prevent the deployment of the side
airbags and increase the risk of injury in an accident.
WARNING:
Do not lean your head on the door. The side airbag
could injure you as it deploys from the side of the seatback.
WARNING:
Do not attempt to service, repair, or modify the
airbag SRS, its fuses or the seat cover on a seat containing an
airbag. Contact your authorized dealer as soon as possible.
WARNING:
All occupants of the vehicle should always wear
their safety belts even when an airbag SRS is provided.
Seating and Safety Restraints
199
WARNING:
Several air bag system components get hot after
inflation. Do not touch them after inflation.
WARNING:
If the side
airbag has deployed,
the
airbag will not function again.
The side airbag system
(including the seat) must be
inspected and serviced by an
authorized dealer .
If the airbag
is not replaced, the unrepaired
area will increase the risk of injury
in a collision.
Safety Canopy
²
system
WARNING:
Do not place
objects or mount equipment
on or near the headliner at the
siderail that may come into
contact with a deploying Safety
Canopy
±
. Failure to follow these
instructions may increase the risk
of personal injury in the event of a
collision.
WARNING:
Do not lean your head on the door. The Safety
Canopy
±
could injure you as it deploys from the headliner.
WARNING:
Do not attempt to service, repair, or modify the
Safety Canopy
±
system, its fuses, the A, B, or C pillar trim, or
the headliner on a vehicle containing a Safety Canopy
±
. Contact your
authorized dealer as soon as possible.
Seating and Safety Restraints
201
WARNING:
Loaded vehicles, with a higher center of gravity,
may handle differently than unloaded vehicles. Do not overload
your vehicle and use extra precautions, such as driving at slower
speeds, avoiding abrupt steering changes and allowing for increased
stopping distance, when driving a heavily loaded vehicle. Over-loading
or loading the vehicle improperly can deteriorate handling capability
and contribute to loss of vehicle control and vehicle rollover.
BRAKE-SHIFT INTERLOCK
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the on position unless brake pedal is pressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the on position and the brake pedal pressed:
1. Apply the parking brake, turn ignition key to off, then remove the key.
2. Remove the rubber pad at the
bottom of the cup holder to locate
the access cap of the floor shifter
assembly.
3. Using a screwdriver (or
equivalent), remove the access
panel and depress the shifter lever
on the shift mechanism.
4. Apply the brake and shift into N
(Neutral).
5. Return the cover plug to the console access hole. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
WARNING:
Do not drive your vehicle until you verify that the
brakelamps are working.
WARNING:
Always set the parking brake fully and make sure
the gearshift is latched in P (Park). Turn the ignition to the off
position and remove the key whenever you leave your vehicle.
Driving
276
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini fuses
Standard
fuses
Maxi fuses
Cartridge
maxi fuses
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
40A
Orange
Green
50A
Red
Red
60A
Blue
Yellow
70A
Tan
80A
Natural
15
Roadside Emergencies
295
Passenger compartment fuse panel
The fuse panel is located below the
instrument panel on the driver’s
side.
To remove a fuse use the fuse puller tool provided on the fuse panel box.
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
20A
Moon roof, Adjustable pedals,
Memory seats, Lumbar motor
2
5A
Microcontroller power
3
20A
Radio, Navigation amplifier, GPS
module
4
10A
On-board diagnostic (OBD II)
connector
CB1
4
3
2
1
8
7
6
5
12
11
10
9
16
15
14
13
20
19
18
17
24
23
22
21
28
27
26
25
Roadside Emergencies
296
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
5
5A
Moon roof, Door lock switch
illumination, Auto dimming rear
view mirror
6
20A
Liftglass release motor, Door
unlock/lock
7
15A
Trailer stop/turn
8
15A
Ignition switch power, Passive
anti-theft system (PATS), Cluster
9
2A
6R Transmission control
module/Powertrain control
module (Ignition RUN/START),
Fuel pump relay
10
5A
Front wiper RUN/ACC relay in
power distribution box (PDB)
11
5A
Radio start
12
5A
Rear wiper motor RUN/ACC,
Trailer battery charge relay in
PDB, Radio
13
15A
Heated mirror, Manual climate
rear defrost indicator
14
20A
Horn
15
10A
Reverse lamps
16
10A
Trailer reverse lamps
17
10A
Restraints control module,
Passenger occupancy
18
10A
Reverse park aid, Roll stability
control™ (RSC
±
) switch, RSC
±
,
All wheel drive (AWD) module,
Heated seat switches, Auxiliary
climate control
19
Not used
20
10A
Climate control system, Brake
shift
Roadside Emergencies
297
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
21
Not used
22
15A
Brake switch, Bi-color stop lamps,
High-mount brake lamp, All turn
lamps
23
15A
Interior lamps, Puddle lamps,
Battery saver, Instrument
illumination, Homelink
24
10A
Cluster, Theft indicator light
25
15A
Trailer tow park lamps
26
15A
License plate/rear park lamp,
Front park lamps, Manual climate
27
15A
Tri-color stop lamps
28
10A
Climate controls
CB1
25A
Windows
The following relays are located on either side of the passenger
compartment fuse panel. See your authorized dealer for service of these
relays.
Fuse/Relay Location
Description
Relay 1
Delayed accessory relay
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
WARNING:
Always disconnect the battery before servicing high
current fuses.
WARNING:
To reduce risk of electrical shock, always replace
the cover to the Power Distribution Box before reconnecting the
battery or refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
Roadside Emergencies
298
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
1
50A**
Battery feed 2 (passenger
compartment fuse panel)
2
50A**
Battery feed 3 (passenger
compartment fuse panel)
3
50A**
Battery feed 1 (passenger
compartment fuse panel)
4
30A**
Fuel pump, Injectors
5
30A**
Third row seat (left)
6
40A**
Anti-lock brake system (ABS) pump
7
40A**
Powertrain control module (PCM)
8
Not used
9
Not used
10
30A**
Power seat (right)
11
30A**
Starter
12
30A**
Third row seat (right)
Roadside Emergencies
299
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
13
30A**
Trailer tow battery charger
14
30A**
Memory seats
40A**
Non-memory seats
15
40A**
Rear defrost, Heated mirrors
16
40A**
Front blower motor
17
30A**
Trailer electronic brakes
18
30A**
Auxiliary blower motor
19
30A**
Running boards
20
30A**
Front wiper motor
21
20A*
Rear power point
22
20A*
Subwoofer
23
Not used
24
10A*
PCM – keep alive power, Canister
vent
25
20A*
Front power point/Cigar lighter
26
20A*
All wheel drive (AWD) module (4.6L
engine only)
27
20A*
6R Transmission module (4.6L
engine only)
28
20A*
Heated seats
29
15A*
Headlamps (right)
30
25A*
Rear wiper
31
15A*
Fog lamps
32
5A*
Power mirrors
33
30A*
ABS valve
34
15A*
Headlamps (left)
35
10A*
A/C clutch
36
20A*
Console bin power point
37
30A*
Driver window motor
38
15A*
5R Transmission (4.0L engine only)
39
15A*
PCM power
Roadside Emergencies
300
Fuse/Relay
Location
Fuse Amp
Rating
Protected Circuits
40
15A*
Fan clutch, Positive crackcase
ventilation (PCV) valve, A/C clutch
relay
41
15A*
Satellite radio module, DVD, SYNC
±
42
15A*
Redundant brake switch, Electronic
vapor management valve, Mass air
flow sensor, Heated exhaust gas
oxygen (HEGO) sensor, EVR,
Variable cam timing (VCT)1 (4.6L
engine only), VCT2 (4.6L engine
only), CMCV (4.6L engine only),
Catalyst monitor sensor
43
15A*
Coil on plug (4.6L engine only), Coil
tower (4.0L engine only)
44
15A*
Injectors
45B
Not used
45A
Not used
46B
Not used
46A
Not used
49
Fuel pump relay
50B
A/C clutch relay
50A
Fog lamps relay
51
Not used
52
Not used
53
One touch integrated start (OTIS)
(diode)
54
Trailer battery charger relay
55B
Front wiper relay
55A
PCM relay
56B
Starter relay
56A
Blower relay
* Mini Fuses ** Cartridge Fuses
Roadside Emergencies
301