Ford Monterey - 2006 Fuse Box Diagram

Ford Monterey - 2006 Fuse Box Diagram

Resetting the PSD
The power sliding door may operate incorrectly or not at all because of
the following conditions:
a low voltage or dead battery
the door is left opened for more than 6 hours
the battery is disconnected
the PSD Passenger compartment fuse panel fuse (fuse #11) is
removed or blown. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
If any of the above conditions has occurred, perform the following steps
to reset the PSD so that electronics can relearn the open and closed
positions:
1. Check to see if PSD is securely closed.
2. Make sure the gearshift is in (P) Park.
3. Push the PSD control on the overhead console to open the door.
4. Wait five (5) seconds and close the door by pressing the PSD control
on the overhead console.
5. Wait five (5) seconds and repeat Steps 3 and 4 then go on to Step 6.
6. Repeat Steps 3–5 for opposite door.
If the door still does not operate correctly:
7. Ensure the ignition is in the OFF position
8. Remove the PSD fuse (fuse #11) from the passenger fuse panel and
leave it out for thirty (30) seconds. Refer to the chapter on Fuses and
Relays. Refer to
Fuses and relays
in the
Roadside emergencies
chapter.
9. Reinstall the fuse and wait ten (10) seconds.
10. Repeat Steps 1–6 above.
If the door still does not operate correctly, see your dealer for service.
Sliding Door Child Safety Lock
Your vehicle is equipped with a sliding door child safety lock that helps
prevent passengers from operating the sliding door by using the inside
door handle, refer to the
Childproof door locks
in the
Locks and
security
chapter.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
61
To open the sliding door when the
child safety lock is on:
Unlock the sliding door and open
the door from the outside.
Press the right or left hand
control on the overhead console
or the remote to open the door.
The second row passenger switch will still be functional to open the
door. To prevent the second row passenger from operating the PSD,
turn the Power Door Lockout control to the OFF position.
INSTRUMENT PANEL STORAGE COMPARTMENT
The storage compartment may be
used to secure sunglasses or similar
sized objects. Press the control to
open the storage compartment.
CLOCK (IF EQUIPPED)
Press the right (+) control to move
the time display forwards.
Press the left (-) control to move
the time display backwards.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
62
Do not use the power point for operating the cigarette lighter element (if
equipped).
To prevent the fuse from being blown, do not use the power point(s)
over the vehicle capacity of 12 VDC/180W.
To prevent the battery from being discharged, do not use the power
point longer than necessary when the engine is not running.
Always keep the power point caps closed when not being used.
There are up to three auxiliary power points in the following locations:
Located on the instrument panel.
Located next to the second row
seat.
Located on the right trim panel in
the rear cargo area.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
63
The keypad can be operated with the factory set 5–digit entry code; this
code is located:
on the owner’s wallet card in the glove box,
marked on the passenger compartment fuse panel (located below and
to the left of the steering, near the brake pedal),
and is available from your
authorized dealer.
You can also create your own 5–digit
personal entry code.
When pressing the controls on the
keypad, press the middle of the
controls to ensure a good activation.
Programming a personal entry
code
To create your own personal entry code(s):
1. Enter the factory set code.
Note:
The driver’s door will unlock.
2. Within five seconds press and release the 1
2 on the keypad.
Note:
The lock motors will cycle, locked then unlocked.
3. Enter your personal 5-digit code. Each number must be entered
within five seconds of each other.
4. Enter a sixth digit if you wish to have the personal entry code recall
memory position Driver 1 or Driver 2 (if equipped with the memory
seat/side view mirrors/adjustable pedals feature).
Note:
The lock motors
will cycle, locked then unlocked.
Press 1
2 to recall the Driver 1 position.
Press 3
4 to recall the Driver 2 position.
5. After five seconds of keypad inactivity, programming mode is exited.
All of the vehicle doors will lock and unlock to confirm the code has
been stored. Each memory feature driver position (Driver 1 or Driver 2)
can be associated with only one personal code. The factory-set code
cannot be associated with a memory recall position.
You can program up to three personal codes; these codes do not replace
the factory-set code.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Locks and Security
101
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
Do not put anything on or over the airbag module. Placing
objects on or over the airbag inflation area may cause those
objects to be propelled by the airbag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your authorized
dealer.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the airbag system, increasing the
risk of injury. Do not modify the front end of the vehicle.
Children and airbags
Children must always be properly
restrained. Accident statistics
suggest that children are safer when
properly restrained in the rear
seating positions than in the front
seating position. Failure to follow
these instructions may increase the
risk of injury in a collision.
Airbags can kill or injure a
child in a child seat.
NEVER
place a rear-facing child
seat in front of an active airbag. If
you must use a forward-facing
child seat in the front seat, move
the seat all the way back.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
149
Do not lean your head on the door. The side airbag could injure
you as it deploys from the side of the seatback.
Do not attempt to service, repair, or modify the airbag SRS, its
fuses or the seat cover on a seat containing an airbag. See your
authorized dealer.
All occupants of the vehicle should always wear their safety belts
even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags.
The side airbag system consists of
the following:
An inflatable nylon bag (airbag)
with a gas generator concealed
behind the outboard bolster of
the driver and front passenger
seatbacks.
A special seat cover designed to
allow airbag deployment.
The same readiness airbag light,
electronic control and diagnostic
unit as used for the front airbags.
Two crash sensors located under
the outboard side of the front
seats, attached to the floor.
Side airbags, in combination with
seat belts, can help reduce the risk of severe injuries in the event of a
significant side impact collision.
The side airbags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the airbag on the side affected by
the collision will be inflated, even if the respective seat is not occupied.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
157
Do not lean your head on the door. The Safety Canopy
±
could
injure you as it deploys from the headliner.
Do not attempt to service, repair, or modify the Safety Canopy
±
system, its fuses, the A, B, C or D pillar trim, or the headliner on
a vehicle containing a Safety Canopy
±
. See your authorized dealer.
All occupants of the vehicle including the driver should always
wear their safety belts even when an airbag SRS and Safety
Canopy
±
system is provided.
To reduce risk of injury, do not obstruct or place objects in the
deployment path of the inflatable Safety Canopy
±
.
How does the Safety Canopy
´
system work?
The design and development of the
Safety Canopy
±
system included
recommended testing procedures
that were developed by a group of
automotive safety experts known as
the Side Airbag Technical Working
Group. These recommended testing
procedures help reduce the risk of
injuries related to the deployment of
side airbags (including the Safety
Canopy
±
).
The front passenger sensing system
will disable the side airbag if the
seat is empty.
The Safety Canopy
±
system
consists of the following:
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
159
capacity to carry you, 4 of your friends and all the golf bags? You and
four friends average 220 lb. (99 kg) each and the golf bags weigh
approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 –
(5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb. Yes, you have
enough load capacity in your vehicle to transport four friends and
your golf bags. In metric units, the calculation would be: 635 kg —
(5 x 99 kg) — (5 x 13.5 kg) = 635 — 495 — 67.5 = 72.5 kg.
A final example for your vehicle with 1400 lb. (635 kg) of cargo and
luggage capacity. You and one of your friends decide to pick up
cement from the local home improvement store to finish that patio
you have been planning for the past 2 years. Measuring the inside of
the vehicle with the rear seat folded down, you have room for 12-100 lb.
(45 kg) bags of cement. Do you have enough load capacity to
transport the cement to your home? If you and your friend each weigh
220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x 100) =
1400 – 440 – 1200 = – 240 lb. No, you do not have enough cargo
capacity to carry that much weight. In metric units, the calculation
would be: 635 kg — (2 x 99 kg) — (12 x 45 kg) = 635 — 198 — 540 =
—103 kg. You will need to reduce the load weight by at least 240 lb.
(104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load
calculation would be:
1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lb. Now you
have the load capacity to transport the cement and your friend home. .
In metric units, the calculation would be: 635 kg — (2 x 99 kg) —
(9 x 45 kg) = 635 — 198 — 405 = 32 kg.
The above calculations also assume that the loads are positioned in your
vehicle in a manner that does not overload the Front or the Rear Gross
Axle Weight Rating specified for your vehicle on the Safety Compliance
Certification Label found on the edge of the driver’s door.
TRAILER TOWING
Your vehicle is capable either of towing Class I trailers or up to Class II
trailers when equipped with the optional trailer tow package.
If your vehicle does not have the optional trailer tow package your
vehicle is partially prepped for trailer tow lamp wiring but you will also
need to install electrical kit (15A416). This kit contains fuses and relays
to isolate the vehicle lighting circuitry from the trailer lighting and an
adapter wiring harness containing the standard 4-pin trailer plug. Refer
to the
Trailer lamps
section in this chapter for additional information.
Do not tow above 2,000 lb. (907 kg) without the
manufacturer-installed trailer tow package.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Tires, Wheels and Loading
205
A new underbody wiring harness (14406) will be a component to this kit
and will need to be installed, if applicable, per instructions located in the
service kit.
If your vehicle has the optional trailer tow package it comes with heavy
duty cooling fans, auxiliary transmission fluid cooler, an auxiliary engine
oil cooler, heavy duty battery, trailer tow wiring (including fuses and
relays to isolate the vehicle lighting circuitry from the trailer lighting)
and a kit (in a cardboard box) that includes an adapter wiring harness
that contains the standard 4-pin trailer plug.
Trailer towing puts additional loads on your vehicle’s engine,
transmission, axle, brakes, tires, and suspension. For your safety and to
maximize vehicle performance, be sure to use the proper equipment
while towing.
Follow these guidelines to ensure safe towing procedure:
Stay within your vehicle’s load limits. If exceeded, cargo should be
removed from the trailer and/or the vehicle until all weights are within
specified limits.
Thoroughly prepare your vehicle for towing. Refer to
Preparing to
tow
in this chapter.
Use extra caution when driving while trailer towing. Refer to
Driving
while you tow
in this chapter.
Service your vehicle more frequently if you tow a trailer. Refer to
Special Operating Conditions
in the scheduled maintenance
information.
Do not tow a trailer until your vehicle has been driven at least
500 miles (800 km).
Refer to the instructions included with towing accessories for the
proper installation and adjustment specifications.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Tires, Wheels and Loading
206
If the steering wanders or pulls, check for:
an improperly inflated tire
uneven tire wear
loose or worn suspension components
loose or worn steering components
improper steering alignment
A high crown in the road or high crosswinds may also make the steering
seem to wander/pull.
AUTOMATIC TRANSAXLE OPERATION
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the 4 (ON) position unless the brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with the ignition
in the 4 (ON) position and the brake pedal depressed:
1. Apply the parking brake.
2. Insert the key and turn it to the 3
(OFF) position.
Apply the brake
pedal and shift to N (Neutral)
.
When the key is in the ignition and in the 3 (OFF) position, the
automatic transmission shift lever can be moved from the P
(Park) position without the brake pedal depressed. To avoid unwanted
vehicle movement, always set the parking brake.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
3
1
2
5
4
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
219
This switch is located behind the
service panel on the right side of
the cargo area.
To reset the switch:
1. Turn the ignition OFF.
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the
switch by pushing in on the reset
button.
4. Turn the ignition ON.
5. Wait a few seconds and return
the key to OFF.
6. Make another check for leaks.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
15
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
229
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
70A
Tan
Brown
80A
Natural
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses. To remove
the fuse panel cover, pull up on the latch on the right or left side of the
cover.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
230
The fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
Relay
Accessory delay relay 1
2
Relay
Accessory delay relay 2
3
10A
Front wiper motor Run feed
4
5A
B+ feed to outside mirrors
5
20A
Vent window power feed/Radio
feed
6
5A
Driver door switch
illumination/Passenger door
switch illumination
7
10A
Rear wiper Run feed
8
10A
Cluster/Electronic Automatic
Temperature Control (EATC) B+
feed, DVD
9
10A
Passive Anti-theft System (PATS)
LED feed
10
5A
Auxiliary radio
11
5A
Auxiliary climate control
system/Power Liftgate
Module/Left and right power
sliding door module/Data Link
Connector (DLC)/Clock B+ feeds
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
231
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
12
5A
Brake-Shift Interlock (BSI) Run
feed, Climate control system Run
feed
13
5A
Compass/Driver heated
seat/Passenger heated
seats/Reverse sensing
system/Power Liftgate
Module/Power sliding door Run
feeds
14
5A
Underhood fuse box Run feed,
Front blower Run feed
15
10A
Brake On-Off (BOO) switch B+
16
5A
Steering angle/Cluster/Power
sliding door and power liftgate
inhibit LED/Electrochromatic
mirror Run/Start/Tire Pressure
Monitoring System (TPMS)
17
10A
Restraint Control Module
(RCM)/Passenger Air bag Disable
Indicator (PADI)/Passenger
Occupant Detection System
(PODS) Run/Start
18
10A
Anti-lock Brake System (ABS)
module/Brake pressure
switch/Speed control Run/Start
19
5A
PATS/Cluster/Air bag
LED/Powertrain Control Module
(PCM) relay Run/Start
20
10A
Liftgate Start feed, Radio Start
feed
21
10A
Starter relay power START
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
232
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
The cover for the power distribution box can be removed by releasing
the tab on the back left corner of the cover, then pulling the cover up.
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
Not used
2
30A**
Right cooling fan
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
233
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
3
30A**
Left cooling fan
4
30A**
Starter solenoid
5
30A**
Right-hand power sliding door
6
30A**
SJB accessory #2 (driver power
window)
7
30A**
Auxiliary blower motor
8
40A**
Anti-lock Brake System (ABS) #2
(coil power)
9
30A**
Power liftgate
10
30A**
SJB accessory #1 (passenger
window, radio, vent windows)
11
30A**
Left power seat/heated seat
12
40A**
ABS #1 (pump motor)
13
40A**
Rear defroster
14
30A**
Front climate control system
blower motor
15
30A**
Right power seat/heated seat
16
30A**
Left-hand power sliding door
20
Mini relay
Powertrain Control Module (PCM)
power
21
Mini relay
Horn
22
Micro relay
A/C clutch
23
Micro relay
High beams
24
Mini relay
Starter
25
Micro relay
Fuel pump
26
Micro relay
Fog lamps
27
Not used
28
Mini relay
Auxiliary blower
29
Micro relay
Trailer park lamps
30
Micro relay
Left trailer stop/turn lamps
31
Micro relay
Right trailer stop/turn lamps
32
Mini relay
Rear defroster
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
234
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
40
15A*
Engine #1 (A/C relay coil, IMRC,
HEGO sensors, Canister purge,
Transmission module)
41
25A*
Horn
42
10A*
A/C clutch
43
15A*
Engine #2 (Cooling fan relays,
Injectors, PCM, MAF sensor, IAC,
Ignition coil, ESM)
44
10A*
Heated PCV
45
15A*
High beams
46
20A*
Trailer stop/turn lamps
47
15A*
Fuel pump, Fuel pump shut-off
switch
48
15A*
Fog lamps
49
10A*
PCM KAP, Canister vent
50
10A*
Alternator
51
10A*
Adjustable pedals (non-memory)
or memory module
52
20A*
Trailer tow park lamps
53
10A*
Heated mirrors
54
30A*
Front wiper motor
55
25A*
Rear wiper motor
56
30A*
Premium sound radio
57
Not used
58
30A*
SJB #1 – Center High-Mounted
Stop Lamp (CHMSL), License
plate lamps, OBD II, Dome lamp,
Auxiliary blend doors, Switch
illumination (feeds F–8, F–9, F–10
and F–11)
59
20A*
Radio (non-premium)
60
30A*
SJB #4 – Back-up lamps, Door
locks
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
235
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
61
Not used
62
30A*
SJB #3 – Right cornering/auxiliary
lamps, Right low beam, Left front
park/turn lamps, Left rear
park/stop/turn lamps, Instrument
panel courtesy lamps, Step well
lamps, Left signal mirror, Clock,
Cluster, Message center (SJB
F–15), Switch illumination for:
overhead console, DVD/Rear
climate control system, Headlamp
switch illumination, Climate
control illumination
63
20A*
Instrument panel power point,
Cigar lighter
64
20A*
Ignition switch #1 feed
65
30A*
SJB #2 – Left cornering/auxiliary
lamps, Left low beam, Right front
park/turn lamps, Right rear
park/stop/turn lamps, Puddle
lamps, Mirror signals, Visors, 2nd
and 3rd row lamps, Cargo lamp,
Defroster indicator
66
20A*
2nd and 3rd row seat power
points
67
20A*
Ignition switch #2 feed
70
Not used
71
Not used
72
Not used
73
Not used
74
Not used
75
Diode
PCM
76
Diode
A/C clutch
* Mini Fuse ** Cartridge Fuse
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
236
Auxiliary relay box (cooling fans)
The relay box is located in the engine compartment by the radiator.
Fuse/Relay
location
Fuse amp
rating
Description
1
Cooling fan relay #4
2
Cooling fan relay #5
3
Cooling fan relay #3
4
Cooling fan relay #1
5
Cooling fan relay #2
6
40A*
Right-hand cooling fan motor (Vehicles with
trailer tow package only)
7
15A**
Low-speed cooling fan circuit breaker
(Vehicles with trailer tow package only)
8
40A*
Left-hand cooling fan motor (Vehicles with
trailer tow package)
10A**
Low-speed cooling fan circuit breaker
(Vehicles without trailer tow package)
* Maxi fuse **Circuit breaker
CHANGING A FLAT TIRE
If you get a flat tire while driving:
do not brake heavily.
gradually decrease the vehicle’s speed.
hold the steering wheel firmly.
slowly move to a safe place on the side of the road.
If your low tire warning light is on, refer to
Low tire warning
in this
chapter.
2006 Monterey
(mty)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
237